RHINO 301001 Fence Pro Gas Petrol Post Driver Owner’s Manual
- August 16, 2024
- RHINO
Table of Contents
RHINO 301001 Fence Pro Gas Petrol Post Driver
Specifications
- Model: 301001
- Engine: Honda GX35 Engine
Product Usage Instructions
Safety Precautions
Always prioritize safety when using the Fence Pro™ Gas/Petrol Post Driver.
Follow all safety instructions provided in the manual.
Assembly
Refer to the parts list provided in the manual to correctly assemble the
post driver components. Make sure all parts are securely fastened.
Operating the Post Driver
- Attach the handle assembly securely to the post driver body.
- Ensure all O-rings and seals are in place and in good condition.
- Connect the throttle control assembly for engine operation.
- Start the Honda GX35 engine as per the engine manual instructions.
- Position the post driver correctly on the post and initiate driving action.
Maintenance
- Regularly inspect all components for wear or damage.
- Keep the post driver clean and free from debris.
- Lubricate moving parts as recommended in the manual.
- Follow maintenance schedules to ensure optimal performance.
FAQ
-
Q: Where can I find replacement parts for the Fence Pro™ Gas/Petrol Post Driver?
A: Replacement parts, including Honda engine parts, are available from your local Honda dealer or authorized distributors. -
Q: What should I do if I encounter a problem with my post driver?
A: Refer to the troubleshooting section of the owner’s manual for common issues and solutions. If problems persist, contact Rhino Tool Company for further assistance.
Fence Pro™
GAS/PETROL POST DRIVER OWNERS MANUAL
MODEL: 301001
TAKE SAFETY SERIOUSLY
This book contains important safety information. Please read it carefully.
This owner’s manual is considered a permanent part of the post driver and
should remain with the post driver if resold, rented or loaned.
Your safety, and the safety of others, is very important. The proper and safe
use of your Rhino® post driver is an important responsibility and should be
taken seriously.
Keep this owner’s manual available, so you can refer to it at any time. This
owner’s manual is considered a permanent part of the post driver and should
remain with the post driver if resold.
The information and specifications included in this publication were in effect
at the time of approval for printing. Rhino Tool Company, Inc. reserves the
right, however, to discontinue or change specifications or design at any time
without notice and without incurring any obligation whatever. No part of this
publication may be reproduced without written permission from:
Rhino Tool Company
To help you make informed decisions about safety, you will find important
safety information in a variety of forms, including:
- Safety Labels on the post driver
- Safety Messages Preceded by a safety alert symbol and one of three signal words, DANGER, WARNING, or CAUTION. These signal words mean:
DANGER
Immediate hazards that will result in severe personal injury or death.
WARNING
Hazards or unsafe practices that could result in personal injury.
CAUTION
Hazards or unsafe practices that could result in injury, product or property
damage.
- Safety Headings such as IMPORTANT SAFETY INFORMATION.
- Safety Section such as POST DRIVER SAFETY.
- Instructions how to use this post driver correctly and safely.
RHINO® FENCE PRO™ PARTS
| No. | P/N | Description |
|---|---|---|
| 1 | 300715-4 | Top Handle Bolt (Qty. of 4) |
| 2 | 301222 | Top Handle Assembly |
| 3 | 301221-2 | Handle Collar (Qty. of 2) |
| 4 | 610010-4 | Handle Anti-Vibration Spring (Qty. of 4) |
| 5 | 300214 | Top Handle Bracket |
| 6 | 301015 | Post Driver Body with Cylinder and Bearings |
| 7 | 301075 | Piston and Connecting Rod Assembly |
| 8 | 301610-2 | Piston O-ring Seal and Hammer O-ring Seal (Qty. of 2) |
| 9 | 301080 | Hammer |
| 10 | 301110 | Anvil O-ring Retainer |
| 11 | 300712 | Ground Bolt |
| 12 | 300250 | Throttle Control Assembly |
| No. | P/N | Description |
| --- | --- | --- |
| 13 | 300221 | EPDM Handle Grip |
| 14 | 301614-2 | Large Retainer O-ring Seal (Qty. of 2) |
| 15 | 301100 | Large Retainer |
| 16 | 301090 | Anvil O-ring Cup |
| 17 | 301160 | Anvil |
| 18 | 301616 | Anvil O-ring |
| 19 | 301618 | Chuck Tube O-ring Seal |
| 20 | 301034 | Lower Body and Chuck Assembly* |
| 21 | 301232 | Handle (2 per driver) |
| 22 | 300702-4 | Lower Body Bolts Set |
| 23 | 300902 | Rhino® Chuck-Lok™ System 2″ Adapter (1 per driver) |
| 24 | 301920 | Rhino® Chuck-Lok™ System Locking Nut |
*For Serial # 9002752 and below use part no. 301033
NOTE
Disassembly of the Crankcase will break the tamper evident seal, thereby
voiding the warranty on the driver
| No. | P/N | Description |
|---|---|---|
| 6 | 301015 | Post Driver Body with Cylinder and Bearings |
| 25 | 300132 | Crankcase Cover |
| 26 | 301617 | Crankcase Cover O-ring Seal |
| 27 | 300050 | Crank Pin |
| 28 | 300704-6 | Crankcase Bolts (Qty. of 6) |
| 29 | 300040 | Crankshaft |
| 30 | 300782-4 | Retaining Ring for Crankshaft & Clutch Drum with Pinion Gear |
(Qty. of 4)
31| 300200| Gear
32| 300730| Key
33| 300700-4| Clutch Housing Bolts (Qty. of 4)
34| 300025| Clutch Housing with Bearings
35| 300120| Clutch Drum with Pinion Gear
36| 300184| Honda OEM Tank Guard Kit
37| 300183| Tank Guard
38| 504015-2| Bolts (qty. of 2)
39| 504016-2| Bolts (qty. of 2)
| 300240| Honda GX35 Engine
| | Honda Engine Parts are Available from Your Local Honda Dealer
| 301800| GPD-40 Fence Pro™ Owner’s Manual
| 300805| Safety Label and Tag Set
| |
No.| P/N| Description
6| 301015| Post Driver Body with Cylinder and Bearings
25| 300132| Crankcase Cover
26| 301617| Crankcase Cover O-ring Seal
27| 300050| Crank Pin
28| 300704-6| Crankcase Bolts (Qty. of 6)
29| 300040| Crankshaft
30| 300782-4| Retaining Ring for Crankshaft & Clutch Drum with Pinion Gear
(Qty. of 4)
31| 300200| Gear
32| 300730| Key
33| 300700-4| Clutch Housing Bolts (Qty. of 4)
34| 300025| Clutch Housing with Bearings
35| 300120| Clutch Drum with Pinion Gear
36| 300184| Honda OEM Tank Guard Kit
37| 300183| Tank Guard
38| 504015-2| Bolts (qty. of 2)
39| 504016-2| Bolts (qty. of 2)
| 300240| Honda GX35 Engine
| | Honda Engine Parts are Available from Your Local Honda Dealer
| 301800| GPD-40 Fence Pro™ Owner’s Manual
| 300805| Safety Label and Tag Set
| |
No.| P/N| Description
---|---|---
Accessories
23| 300902| Rhino® Chuck-Lok™ System 2″ (50.8mm) Adapter
| 300895| Rhino® Chuck-Lok™ System 1-3/4″ (44.4mm) Adapter (optional)
| 300900| Rhino® Chuck-Lok™ System 1″ (25.4mm) Adapter (optional)
24| 301920| Rhino® Chuck-Lok™ Locking Nut
| 301233| Lower Handle Assembly (optional)
| 301152| Fence Pro™ Short Euro Stake Chuck Tube
| 301000| ¼” Long Arm Hex Key
| 300500| Rhino® Pro Series Lubricant
| 301508| Service Kit for Fence Pro™ without O-Ring Cup
Bolt Torque Specifications
1| 300715-4| Top Handle Bolts (Qty. of 6) – 132.0 in/lbs (14.91 Nm)
22| 300702-4| Lower Body Bolts (Qty. of 4)- 132.0 in/lbs (14.91 Nm) 251 lb/in
(28.4 Nm) for black oxide bolts
27| 300050| Crank Pin (Left Hand Threads)- 360.0 in/lbs (40.6 Nm)
28| 300704-6| Crankcase Bolts (Qty. of 6) 75.0 in/lbs (8.5 Nm)
33| 300700-4| Clutch Housing Bolts (Qty. of 4)- 95.0 in/lbs (10.73 Nm)
39| 300706-2| Shroud Bolt (Qty. of 2)- 56.4 in/lbs (6.37 Nm)
40| 300705-2| Lower Shroud Bolt (Qty. of 2) – 56.4 in/lbs (6.37 Nm)
No.| P/N| Description
Accessories
23| 300902| Rhino® Chuck-Lok™ System 2″ (50.8mm) Adapter
| 300895| Rhino® Chuck-Lok™ System 1-3/4″ (44.4mm) Adapter (optional)
| 300900| Rhino® Chuck-Lok™ System 1″ (25.4mm) Adapter (optional)
24| 301920| Rhino® Chuck-Lok™ Locking Nut
| 301233| Lower Handle Assembly (optional)
| 301152| Fence Pro™ Short Euro Stake Chuck Tube
| 301000| ¼” Long Arm Hex Key
| 300500| Rhino® Pro Series Lubricant
| 301508| Service Kit for Fence Pro™ without O-Ring Cup
Bolt Torque Specifications
1| 300715-4| Top Handle Bolts (Qty. of 6) – 132.0 in/lbs (14.91 Nm)
22| 300702-4| Lower Body Bolts (Qty. of 4)- 132.0 in/lbs (14.91 Nm) 251 lb/in
(28.4 Nm) for black oxide bolts
27| 300050| Crank Pin (Left Hand Threads)- 360.0 in/lbs (40.6 Nm)
28| 300704-6| Crankcase Bolts (Qty. of 6) 75.0 in/lbs (8.5 Nm)
33| 300700-4| Clutch Housing Bolts (Qty. of 4)- 95.0 in/lbs (10.73 Nm)
39| 300706-2| Shroud Bolt (Qty. of 2)- 56.4 in/lbs (6.37 Nm)
40| 300705-2| Lower Shroud Bolt (Qty. of 2) – 56.4 in/lbs (6.37 Nm)
RHINO® LIMITED WARRANTY GAS/ PETROL POST DRIVER
Warranty: Rhino Tool Company, Inc. (“Rhino”) warrants to the original
purchaser, purchasing the Equipment in new condition, in original packaging
from an authorized dealer that its Gasoline Powered Post Driver will be free
from defects in workmanship and materials (the “Limited Warranty”).
The Limited Warranty shall survive for the lifetime of the product with
respect to the Hammer and Anvil components and for twelve (12) months with
regard to all other components, excluding the Honda GX35 engine for which
Rhino provides no warranty and for which the warranty provided by American
Honda Motor Co., Inc. shall be the sole warranty applicable thereto. This
Limited Warranty is non-transferable.
For Warranty Claims contact your dealer or distributor. Proof of purchase date
and serial number is required. In the event of a warranty repair, the post
driver should be returned to a Registered and Warranty Authorized Rhino
Servicing Dealer. Rhino’s obligation under this Limited Warranty is expressly
limited to the repair or replacement, at Rhino’s election, of such defective
Gasoline Powered Post Driver, which is proved to be defective upon inspection
by a Rhino-certified/authorized technician.
This Limited Warranty does not extend to a Gasoline Powered Post Driver which
has been subject to misuse, neglect, or accident, nor does it extend to any
Gasoline Powered Post Driver which has been repaired, altered, or serviced by
unauthorized persons. This Limited Warranty does not cover any damage or
adjustments required to any Gasoline Powered Post Driver if such damage or
adjustment is caused by the use of supplies, parts, or attachments not sold or
approved by Rhino
EXCEPT AS OTHERWISE PROVIDED HEREIN, RHINO DIS-CLAIMS ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE. UNDER NO CIRCUMSTANCES
SHALL RHI-NO BE LIABLE FOR ANY LOSS OF BUSINESS, REVENUES, OR PROFIT OR OTHER
INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING OUT OF
ANY DEFECTS IN OR PERFORMANCE OF THE GASOLINE POW-ERED POST DRIVER, HOWSOEVER
CAUSED.
To register your product:
Fill out and mail in registration card supplied with post driver Or online
visit: http://rhinotool.com/contact-support/warranty-information/
Call your local dealer, service center or Rhino Tool Company for more assistance with your post driver
TROUBLESHOOTING
Symptom Explanation/Procedure
Post lodged in the driver| In the event that a driven post flares and becomes lodged within the chuck, follow these steps:
- Turn engine off. Remove the four 5/16” lower body bolts and separate the lower body casting from the driver body.
- Slide the lower body casting down the post to expose the flared top of the post. With the proper cutting tool for the type of post, cut through the post below the flared portion.
- Once the flared portion is removed, slide the lower body casting off the post and reassemble it to the driver. Please follow bolt tightening procedure and use threadlocker.
Recommendation: Do not use “thin-wall” or light gauge round post with the Fence Pro ™ . It is very likely to flare this type of post at full throttle.
Drives post slow or sluggish engine performance:| Typically this is
resulting from improper driver storage or over-filling the oil causing the oil
to seep into the combustion chamber. Position the driver vertically, remove
the dipstick to check oil level. (See page 6) If you need to remove some oil,
dispose of it properly. If oil is at proper level, follow the procedure listed
in “Pull-start is frozen or hard to pull.”
Pull-start is frozen or hard to pull:| This typically results from oil
seeping into the combustion chamber from improper driver storage or
overfilling the oil reservoir of the engine. Remove spark plug and pull hand
grip several times until it pulls freely. Replace the spark plug. Check the
oil level in oil reservoir to ensure proper level (page 6). Follow starting
procedure. It is not unusual, for blue smoke to be emitted from the engine,
let the engine run until smoke clears.
Proper Storage:| Do not lay horizontally on the driver side or resting
on the engine. If the unit cannot be stored securely in the upright position,
place the chuck on a flat surface, leaning toward the engine side until it is
supported by the shroud and chuck. Position the driver on an angle with the
top handle at the topmost point.
Other problems or technical questions| Other problems or technical
questions: Document your serial number and contact Rhino Tool Company. Phone:
309.853.5555 or Toll Free 866-707-1808,
Fax:309.856.5905, Email: service@rhinotool.com
.
© 2013, 2015, 2017 Rhino Tool Company Inc., – All Rights Reserved
A TRADITION OF QUALITY AND SERVICE SINCE 1975
WWW.RHINOTOOL.COM
Form 301800.01.15.2024
Rhino Tool Company, Inc. | P.O. Box 111 | Kewanee, IL 61443
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>