RHINO-RACK S606 Vortex Underbar Retainer Instruction Manual
- October 30, 2023
- RHINO RACK
Table of Contents
RHINO-RACK S606 Vortex Underbar Retainer
Product Information
The S606 Vortex Underbar Retainer is a product designed to secure loads to a roof rack that uses vortex crossbars. The product comes with all the necessary hardware and instructions for installation. It includes two crossbar strap retainers, two M6 x 20mm torx screws, two M6 spring washers, two M6 x 12.5mm flat washers, two M6 nuts, one T27 torx key, and one set of instructions. Tie- down straps are sold separately.
Product Usage Instructions
- Check that the part number/kit is correct before installation.
- Read through the instructions before installing.
- Fit the roof rack accessory.
- Check and recheck that all fasteners are secure.
- Use tie-down straps to secure the load before driving.
- Loosely assemble the supplied hardware as shown in the instructions.
- With the end cap removed from the crossbar, slide the assembly into position (front and rear) and tighten it in place with the torx key provided. Replace the end cap.
- Use a tie-down strap and pull it through the strap retainer.
- Take the strap over the load, around and under the crossbar, and back through the locking mechanism on the strap.
- Ensure the strap is pulled down and taut. This will ensure that the load cannot slide out.
Note for dealers and fitters: It is your responsibility to ensure that these fitting instructions are given to the end user or client.
Tools required: Torx key (provided), tie-down straps (sold separately).
S606 Vortex Underbar Retainer
- Check Part No./Kit is correct
- Read through the instruction before installing
- Fit roof rack accessory
- Check and recheck all fasteners are secure
Parts List
| Item | Component | Qty | Part No. |
|---|---|---|---|
| 1 | M6 x 20mm Torx Screw | 2 | B243 |
| 2 | M6 Spring Washer | 2 | W003 |
| 3 | M6 x 12.5mm Flat Washer | 2 | W004 |
| 4 | Crossbar Strap Retainer | 2 | M870 |
| 5 | M6 Nut 24mm x 21mm | 2 | N057 |
| 6 | T27 Torx Key | 1 | H054 |
| 7 | Instructions | 1 | R1349 |
Note:
For use with vortex crossbars. Tie-down straps are sold separately. Always be
sure the load is secure before driving.
Tools required:
Torx key (provided). Tie-down straps.
Instructions
- Loosely assemble the supplied hardware as shown.
- With the end cap removed from the crossbar, slide the assembly into position (front and rear) and tighten in place with the torx key provided. Replace the end cap.
- Use a tie-down strap, and pull the strap through the strap retainer. Take the strap over the load, around and under the cross-bar, and back through the locking mechanism on the strap. Ensure the strap is pulling down and taught. This will ensure the load cannot slide out.
Note for Dealers and Fitters:
It is your responsibility to ensure these fitting instructions are given to the
end-user or client. Rhino-Rack 3 Pike Street, Rydalmere, NSW 2116, Australia.
- (Ph) (02) 9638 4744
- (Fax) (02) 9638 4822
- Document No: R1349
- Prepared By: Kayle Everett
- Authorized By: Chris Murty
- Fit Time: 5min per Bar
- Issue No: 02
- Issue Date: 21/03/2018
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>