RHINO 301002 Multi Pro XA Gas Petrol Post Driver Owner’s Manual

RHINO 301002 Multi Pro XA Gas Petrol Post Driver

Specifications :

• Model: Multi-ProTM / Multi-Pro XA*
• Serial Numbers: 5005459 or XA04599 and higher
• Models: 301002 / 301003 / 301007 / 301012 / 301014

Product Information
The Multi-ProTM Gas/Petrol Post Driver is a powerful tool designed for driving posts into the ground efficiently. It comes with a range of features and components to ensure reliable performance.

Safety Precautions
Always prioritize safety when using the Multi-ProTM Post Driver.

Follow these safety precautions:

• Read the owner’s manual carefully before use.
• Wear appropriate safety gear, including eye protection and gloves.
• Keep bystanders at a safe distance during operation.
• Ensure the post driver is on stable ground before operation.

Assembly and Setup
Before using the Multi-ProTM Post Driver, assemble it following these steps:

1. Refer to the parts list to ensure all components are included.
2. Assemble the body, handle, piston, anvil, and other components according to the provided instructions.
3. Ensure all bolts and connections are securely tightened.

GAS/PETROL POST DRIVER
OWNERS MANUAL
Serial Numbers: 5005459 or XA04599 and higher

TAKE SAFETY SERIOUSLY

This owner’s manual is considered a permanent part of the post driver and should remain with the post driver if resold, rented or loaned.

Your safety, and the safety of oth-ers, is very important. The proper and safe use of your Rhino® post driver is an important responsibility and should be taken seriously.
Keep this owner’s manual avail-able, so you can refer to it at any time. This owner’s manual is considered a permanent part of the post driver and should remain with the post driver if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Rhino Tool Company, Inc. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission from:

Rhino Tool Company

This book contains important safety information. Please read it carefully.
To help you make informed decisions about safety, you will find important safety information in a variety of forms, including:

• Safety Labels on the post-driver
• Safety Messages Preceded by a safety alert symbol and one of three signal words, DANGER, WARNING, or CAUTION. These signal words mean:

DANGER Immediate hazards that will result in severe personal injury or death.
WARNING Hazards or unsafe practices that could result in personal injury.
CAUTION Hazards or unsafe practices that could result in injury, product or property damage.

• Safety Headings such as IMPORTANT SAFETY INFORMATION.
• Safety Section such as POST DRIVER SAFETY.
• Instructions how to use this post driver correctly and safely.

Regular Maintenance Service Period

Item| Each Use| First Month Or

10 Hours

| Every 3 Months

Or 25 Hours

| Every 6 Months

Or 50 Hours

| Every 12 Months

Or 100 Hours

| Refer to Page
---|---|---|---|---|---|---
Engine Oil Check Level| X| | | | | Page 6
Engine Oil Change| | X| | X| | Page 6
Air Cleaner Check| X| | | | | See Honda

Engine Manual

Air Cleaner

Clean

| | | X (1)| | | See Honda

Engine Manual

Air Cleaner Replace| | | | | X| See Honda

Engine Manual

Crankcase Lubrication Check| X| | | | | Page 12
Check Engine and Post Diver Fasteners| X| | | | | ****

Page 23

Service wear parts with Rhino Service Kit| | | | | X (2)| ****

Page 13

Other Honda Engine Maintenance Schedule| | | | | | See Honda

Engine Manual

1. Service more frequently when used in dusty areas.
2. Check sooner if driver is not pounding.

Rhino® Multi-Pro™ Parts and Accessories List

(qty. of 4)
39| 300200| Gear
40| 300730| Machine Key
41| 300700-4| Clutch Housing Bolt Set (qty. of 4)
42| 300025| Clutch Housing with Bearings
43| 300120| Clutch Drum with Pinion Gear
44| 300132| Pro-Series™ Crankcase Cover – Threaded
45| 301617| O-ring Seal for Pro-Series™ Crankcase Cover – Threaded
46| 300050| Crank Pin (Left Hand Threads)
47| 300704-6| Crankcase Bolt Set (qty. of 6)
48| 300040| Crankshaft

*Please refer to the Multi-Pro Standard Configuration for parts information on the upper portion of the Multi-Pro XA.

Multi-Pro XA ™ ONLY
11| 301097| Multi-Pro™ Anvil O-ring Retainer
12| 301614-2| Large Retainer O-ring Seal Set (qty. of 2)
13| 301105| Multi-Pro™ Large Retainer
14| 301098| Multi-Pro™ Anvil O-ring Cup
16| 301615| Multi-Pro™ Anvil O-ring Seal
19| 301099| Multi-Pro™ Sleeve for Lower Body
20| 301032| Multi-Pro™ Lower Body
21| 300750-4| Multi-Pro™ Lock Washers (qty. of 4)
22| 300701-4| Lower Body Bolt Set (qty. of 4)
23| 300717-4| Multi-Pro™ Chuck Bolt Set (qty. of 4)
24| 301920| Chuck-Lok™ Locking Nut (1 per driver)
29| 300900| Chuck-Lok™ System 1″ (25.4 mm) Adapter
30| 300895| Chuck-Lok™ System 1¾” (44.45 mm) Adapter
31| 300902| Chuck-Lok™ System 2″ (50.8 mm) Adapter
32| 301169| Multi-Pro Extended Anvil
34| 301420| Multi-Pro™ Extended Master Chuck
35| 301159| Multi-Pro™ Channel Post Chuck (Slotted Chuck)

Dealer

| 300805| Safety Label and Tag Set
| 301801| Multi-Pro™ Operating, Safety, and Parts Manual
No.| P/N| Description
---|---|---
Accessories
31| 300902| Chuck-Lok™ System 2″ (50.8mm) Adapter
30| 300895| Chuck-Lok™ System 1¾” (44.4mm) Adapter
29| 300900| Chuck-Lok™ System 1″ (25.4mm) Adapter
24| 301920| Chuck-Lok™ Locking Nut (1 required)
| 301159| Multi-Pro™ Slotted Chuck
| 301169| Multi-Pro™ Extended Anvil
| 301175| Multi-Pro™ U-Channel Drive Kit (includes 301159, 301169)
| 301155| Multi-Pro™ Tent Stake Chuck
| 301400| Large Chuck Adapter (required for all large chucks) Plate*
| 301425| Multi-Pro™ Square Tube Chuck
| 300932| Drive cap for 1¾” (44.4mm) Square Tube
| 300958| Drive cap for 2″ (50.8mm) Square Tube
| 300959| Drive cap for 2¼” (57.15mm) Square Tube
| 300960| Drive cap for 2½” (63.5mm) Square Tube
| 301403| Multi-Pro™ 3½” Round Chuck Assembly
| 301405| Multi-Pro™ 4″ Round Chuck Assembly
| 301415| Multi-Pro™ 3″ Square Chuck Assembly
| 301414| Multi-Pro™ 3″ Round Chuck Assembly
34| 301420| Multi-Pro™ Extended Master Chuck
No.| P/N| Description
---|---|---
| 301422| Multi-Pro™ XA Square Tube Chuck
| 301000| ¼” Long Arm Hex Key
| 300500| Rhino® Pro Series Lubricant
| 300506| Rhino® Pro Series Lubricant – 12-pack
| 301509| Multi-Pro™ Service Kit
Bolt Torque Specifications
4| 300715-4| Pro Series Handle Bolts (qty. of 4) – 132 lb/in (14.91 Nm)
21| 300701-4| Lower Body Bolts (qty. of 4) – 251 lb/in (28.3 Nm)
23| 300717-4| Multi-Pro™ Chuck Bolt Set (qty. of 4) – 251 lb/in (28.3 Nm)
41| 300700-4| Clutch Housing Bolt (qty. of 4) – 95.0 in/lbs (10.73 Nm)
46| 300050| Crank Pin (Left Hand Threads) – 360.0 in/lbs (40.6 Nm)
47| 300704-6| Crankcase Bolt (qty. of 6) – 75.0 in/lbs (8.5 Nm)
52| 300706-2| Shroud Bolt (qty. of 2) – 56.4 in/lbs (6.37 Nm)
53| 300705-2| Shroud Bolt – Self Tapping (qty. of 2) – 56.4 in/lbs (6.37 Nm)

• Requires 301169 Multi-Pro™ Extended Anvil
• Requires 301425 Square Tube Chuck
• Requires 301400 Large Chuck Adapter Plate

Rhino® Limited Lifetime Impact Warranty Gasoline Powered Post Drivers

Warranty: Rhino Tool Company, Inc. (“Rhino”) warrants to the original purchaser, purchasing the Equipment in new condition, in original packaging from an authorized
dealer that its Gasoline Powered Post
Driver will be free from defects in workmanship and materials (the “Limited Warranty”). The Limited Warranty shall survive for the lifetime of the product with respect to the Hammer and Anvil components and for twelve (12) monthscomponents and for twelve (12) months with regard to all other components, excluding the Honda GX35 engine for which Rhino provides no warranty and for which the warranty provided by American Honda Motor Co., Inc. shall be the sole warranty applicable thereto. This Limited Warranty is non- transferable.

For Warranty Claims contact your dealer or distributor. Proof of purchase date and serial number is required. In the event of a warranty repair, the post driver should be returned to a Registered and Warranty Authorized Rhino Servicing Dealer. Rhino’s obliga-tion under this Limited Warranty is expressly limited to the repair or replacement, at Rhino’s election, of such defective Gasoline Powered Post Driver, which is proved to be defective upon inspection by a Rhino-certified/authorized technician.
This Limited Warranty does not extend to a Gasoline Powered Post Driver which has been subject to misuse, neglect, or ac-cident, nor does it extend to any Gasoline Powered Post Driver which has been repaired, altered, or serviced by unauthorized persons. This Limited Warranty does not cover any damage or adjustments required to any Gasoline Powered Post Driver if such  damage or adjustment is caused by the use of supplies, parts, or attachments not sold or approved by Rhino

EXCEPT AS OTHERWISE PROVIDED HEREIN, RHINO DIS-CLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRAN-TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE. UNDER NO CIRCUMSTANCES SHALL RHI-NO BE LIABLE FOR ANY LOSS OF BUSINESS, REVENUES, OR PROFIT OR OTHER INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING OUT OF ANY DEFECTS IN OR PERFORMANCE OF THE GASOLINE POW-ERED POST DRIVER, HOWSOEVER CAUSED.
Registration/Warranty Claims: The purchase of a Rhino Tool, as outlined in the warranty terms, automatically serves as the product registration and the start of the customer’s 1 year warranty. Visit https://rhinotool.com/service/warranties/gas-petrol-post-drivers/ or call your Rhino Dealer or Rhino customer service toll-free at 1-866-707-1808 for assistance.
End of Lifecycle: When your Rhino Gas Powered Driver (Ranch Pro, Fence Pro, Multi-Pro or Multi-Pro XA) is coming to the end of its lifecycle, destruction of the unit needs to be conducted according to international and local environmental regulations. The gas powered driver contains:

• Fuel
• Oil
• Grease
• Electric components
• Plastic, steel and aluminum components.

Call your local dealer, service center or Rhino Tool Company for more assistance with your post driver

TROUBLESHOOTING

Symptom Explanation/Procedure

Post lodged in the driver with adapter installed| Turn off the engine. Remove the Chuck-Lok™ System’s locking nut from the master chuck and slide it down the post. Using the han- dles, lift post driver upward, allowing the adapter to slide out. If the pressure from the flared post does not allow you to lift driver off the post, locate the pry slots on the adapter base and use a slotted screwdriver to pry them downward. Be careful not to damage the master chuck threads. Once loosened, lift using the post driver handles. As the two-piece adapter frees from the chuck tube they separate from the post. Slide the locking nut off the post, reinsert the adapter, apply the locking nut and resume post driving.
Post lodged in master chuck:| Turn off the engine. Remove the four chuck bolts and separate the master chuck from lower body. Slide the master chuck down the post to expose the flared top of the post. With the proper cutting tool for the type of post, cut through the post below the flared portion. Once the flared portion is removed, slide the master chuck off the post and reassemble the chuck to the driver. Please follow bolt tightening procedure and use threadlocker solution. Recommendation: Do not use “thin-wall” or light gauge round post, which may deform or flare the post at full throttle.
Drives post slow or sluggish engine performance:| Typically this is resulting from improper driver storage or over-filling the oil causing the oil to seep into the combustion chamber. Turn off the engine. Position the driver vertically; remove the dipstick to check oil level. (See page 6) If you need to remove some oil, dispose of it properly. If oil is at proper level, follow the procedure listed in “Pull-start is frozen or hard to pull.” It is also good practice to wipe clean the engine after use.
Pull-start is frozen or hard to pull:| This typically results from oil seeping into the combustion chamber from improper driver storage or overfilling the oil reservoir of the en- gine. Remove spark plug and pull hand grip several times until it pulls freely. Replace the spark plug. Check the oil level in oil reservoir to ensure proper level (page 6). Follow starting procedure. It is not unusual, for blue smoke to be emitted from the engine, let the engine run until smoke clears.
Proper Storage:| Do not lay horizontally on the driver side or resting on the engine. If the unit cannot be stored securely in the upright position, place the chuck on a flat surface, leaning toward the engine side until it is supported by the shroud and chuck. Position the driver on an angle with the top handle at the topmost point.
Other problems or technical questions| Other problems or technical questions: Document your serial number and contact Rhino Tool Company. Phone: 309.853.5555 or Toll Free 866-707-1808, Fax:309.856.5905, Email: service@rhinotool.com In Europe contact Eurogate Int. F: (0031) (0) 523 638286, M: (0031) (0) 610 502607.

© 2013, 2015, 2017, 2021 Rhino Tool Company Inc., – All Rights Reserved

A TRADITION OF QUALITY AND SERVICE SINCE 1975

WWW.RHINOTOOL.COM

Rhino Tool Company, Inc. | P.O. Box 111 | Kewanee, IL 61443

References

• Post Drivers, Post Pullers, Hydraulic & Gas Powered | Rhino Tool
• Warranties | Rhino Tool

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>