August VGB400 Digital Converter No PC Required User Manual

August VGB400 Digital Converter No PC Required User Manual

Thank you for purchasing the August VGB400 VHS to Digital Video Conversion Box. This user manual is designed to familiarize you with all the features of this device. Please take the time to read this user manual carefully, even if you are already familiar with a similar product.
Safety
To ensure the safety of you and others, please
read the Safety Instructions before using this device. Please do not disassemble the product, itcan be unsafe and will invalidate the manufacturer’s warranty.
Disposal
Please ensure the product and accessories are disposed of in compliance with the WEEE (Waste Electrical and Electronic Equipment) Directive and any other regulations applicable to your country. Always check with the environment agency and any other relevant authorities for current disposal regulations.
Declaration of Conformity
The Declaration of Conformity can be found on our website at http://augustint.com/en/declaration/
Customer Service
You can contact us by phone on: +44 (0)845 250 0586 or by email at: service@augustint.com  should you require further technical support or customer service.

Safety Instructions

Storage and Use

Maintenance
Please unplug all leads before cleaning this device.

Main Features

• Capture Video from VHS, Camcorder or any Analogue Video Source
• Convert and Save Files to MP4 with One Simple Click
• Compatible with Video Source in NTSC, PAL, and SECAM Formats
• Record to Micro SD or USB and watch along with HDMI Output
• Plug & Play No PC Required

Box Contents

Part Names and Functions

1. RCAIn
2. HDMI Out
3. USB Port
4. USB-C Power
5. Micro SD Card Port
6. Record Button
7. Record Status LED
8. Power LED
9. VIDEO + AUDIO IN — RCA Composite video and L/R audio input from video source device such as VHS. Yellow = video, white = audio left channel, red = audio right channel.

Note: For some VHS video sources a SCART adapter may be required as an output connector. Please use the SCART adaptor provided with an RCA cable connection. Please make sure the SCART is switched to OUTPUT

10. HDMI OUT — Connect to TV or monitor to display video with HDMI Cable. (HDMI Cable is not included.)

USB — Plug USB drive to save recorded video files. Note:  Please do not plug USB drive and Micro SD card at the same time. Supports FAT and NTFS formats, does not support exFAT. The maximum storage size supported is 64GB.

DC — Connect to 5V DC power with USB-C to USB-A cable. (Power adapter is not included.)

Note:  Ensure the output voltage from the USB port or adaptor is 5V/2A. Power voltage greater than 5V may damage the device.

1. Micro SD card — Plug Micro SD card to save recorded files.

Note:  Please do not plug USB drive and Micro SD card at the same time. Supports FAT and NTFS formats, does not support exFAT. The maximum storage size supported is 64GB.

2. Record Button — Press to record video, press again to stop and save file.

Note:  Please press the button to stop the recording first before unplugging the USB Drive or SD Card, failure to do this will cause the recorded file to be damaged.

3. RECORDING LED – The red recording indicator light, it will flash for a few seconds when the USB drive or Micro SD card is inserted and then stays on. This means USB drive or Micro SD card is ready. It flashes when recording. It will be off for few seconds and then reactivate when recording stopped. If you remove the USB drive or Micro SD card, the indicator light will be off. .
4. POWER LED — Flashing a few seconds after connect power DC, then stays green.

Record Video

You will preview the video on TV or monitor when all connections are ready, press RECORD button to record video, and the REC LED will flash in red to show it is recording.
Press the RECORD button again to stop recording, REC LED will be off for few seconds then light on in red. This means recorded video has been saved in Micro SD card or USB drive successfully.

Recorded Files

You will be able to connect a USB drive or Micro SD card to your computer and check the recorded video file after you stop recording. It is named Encode_1.mp4. Each recording/stopping operation will create a different recording file: Encode_1, Encode_2, Encode_3… etc.
The maximum size of each file is about 1.95GB. When you record a video over 1.95GB, VGB400 will split it into multiple files, for example: If you record a long video by one click, you will see 2 or 3 files: Encode_1.mp4, Encode_1_1.mp4, Encode_1_2.mp4… and so on.
If you want to reset the file saving name to start from Encode_0, please press and hold the record button for a while before powering on the device, and then plug in the USB-C power jack to power the device, after 3 seconds, the file number will start from 0.
Note:  Sometimes you may find that some recorded videos have problems, such as skipping frames and distortion. It may be caused by the fact that the USB drive or Micro SD card you are using is in NTFS format and you did not click “Safely Remove Device” when disconnected from the computer. If this problem keeps happening, you can also try formatting it to FAT32.

Specifications

Warranty

This product is guaranteed for twelve months from the date of the original purchase. In the unlikely event of any defect arising due to faulty materials or workmanship, the unit will be either replaced or repaired free of charge (where possible) during this period. An alternative product will be offered in case the product is no longer available or repairable.
This warranty is subject to the following conditions:

• The warranty is only valid within the country where the product is purchased.
• The product must be correctly installed and operated in accordance to the instructions given in this user manual.
• The product must be used solely for domestic purposes.
• The warranty only covers the main unit, and does not cover the accessories.
• The warranty does not cover the damage caused by misuse, negligence, accident and natural disaster.
• The warranty will be rendered invalid if the product is resold or has been damaged by inexpert repairs. The manufactures disclaim any liability for incidental or consequential damages.
• Please consult our customer adviser before returning any product; we are not responsible for any unexpected product returns.
• Any faulty product must be kept and returned in the original packaging with all the accessories and the original copy of the purchase receipt.

The warranty is in addition to, and does not diminish, your statutory or legal rights.
Customer Service:
Telephone: +44(0)845 250 0586
Email:  service@augustint.com
** This product is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. The Declaration of conformity may be consulted online at http://www.augustint.com/en/declaration
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept interference, including interference that may cause undesired operation of the device.
Note:**  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. Therefore, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television  reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorientate or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

No Unauthorized Modifications: Do not make any changes or modifications to this product without the prior express written approval of August International Ltd. Any changes or modifications made without express written approval could void the user’s authority to operate this product.
**** For further details of relevant technical standards, please contact us at the address on the following back page.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>