EPLO DP7 SE Smart Toilet Instruction Manual

EPLO DP7 SE Smart Toilet

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING

DANGER – To reduce the risk of electrocution:

1. Do not use while bathing.
2. Do not place or store product where it can fall or be pulled into a tub or sink.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into water. Unplug immediately.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.
10. Do not use while bathing.
11. Risk of Electric Shock. Connect Only to a Grounding Type Receptacle Protected by a Ground-Fault Circuit-Interrupter (GFCI)
12. CAUTION – Risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel.
    SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
This product is equipped with a cord having a grounding wire with a grounding plug.
The plug must be plugged into an outlet that is properly installed and grounded.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.

The functions may vary from different part no.

Parts Information

Overview, Sideview, Remote controller

Overview

Rotated Switch

Remote Controller

Warnings and Safety

Please read thoroughly
First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference.

The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be held liable for any injuries to the user and damages to the product due to improper usage and/or failure to heed safety warnings.

Explanation of Terms and Symbols

Warning · · (Indicates possible injury resulting from improper usage due to negligence of this sign.)

Attention · · (Indicates human injury or property loss that may result in improper usage due to negligence of this sign.)

(Note) When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions.

( Prohibits any individual from performing any action with this symbol )

( Prohibits any individual from dismantling product. )

(Keep product away from any wet environments, including, but is not limited to, humid environments, close proximities to baths, showers or sinks. )

(Do not touch !)

(Do not touch with a wet hand!)

(Keep away from any extreme heat or fire!)

(operate only as instructed!)

(Pull out the power plug!)

(Protective grounding)

Warning

This product needs to be properly grounded.

• Risk of electric shock
• If unsure, contact an electrician.
  electrical installation company.

Do not touch, insert or pull out the power plug with a wet hand.

• Risk of electric shock.

Do not use a power socket in poor condition or a damaged power plug.

• Risk of fire and/or electric shock.

The power socket in use should be within the specified range (AC120V ).

• Risk of fire and/or electric shock.

Do not pull, damage, bend, twist, stretch, roll, bundle, clamp or squeeze the power cable. Do not place anything on power cable.

• Risk of fire and/or electric shock

If the power cord is damaged, to prevent any injuries or accidents, it should be replaced by a professional.

• Risk of fire and/or electric shock

Do not place a lit cigarette along with other burning objects into the unit.

• Risk of fire.

Do not use during thunderstorms (pull out the power plug during storms). * Failure in doing so may lead to injury or fault in the product.

When the seat ring or the cover plate is damaged, to avoid any harm, be sure to pull off the power plug, close the water source and contact your local distributor for replacement.

• Risk of fire or electric shock.

Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth.

• Risk of fire.

Any person with a disability, the elderly, and children, should be using this product with the supervision of another individual.

• Be advised that sitting on the heated seat for an extended amount of time may result in burns.

This product is not a toy. Advise children not to play with product.

• Risk of injury.

Do not dismantle, repair or alter this product on your own. Call in a professional, or contact Dynon Faucet for further advice.

• Risk of fire, electric shock, and/or other accident that may lead to injury.

Warning

For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. (These include, but are not limited to products such as: concentrate sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetrachloride, chloroform, acetone, butanone, benzene, methylbenzene, phenol, methylphenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc).

• Risk of damaging parts that can lead to accidents and injuries

Do not add water or detergent into the unit or on to the wireless remote. Do not soak the product with water or cleaner.

• Risk of fire and/or electric shock.

Do not install product in a humid environment or a soak room. Do not spray or soak this product with any form of liquid to prevent any damage to the product.

• Risk of fire and/or electric shock.

Do not use polluted water or water meant for industrial.

• Risk of urocystitis or dermatitis.
  Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.

Do not apply any force to the unit’s se and lid. Do not stand on the lid or open or close the lid and the seat forcefully.
*This may result in product damage and/or user injury.

Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use.

• Risk of fire, electric shock, and/or other accident that may lead to user injury.

Do not spray urine at the dryer trap.

• Risk of electric shock.

Read the following for proper battery usage.

• Properly install the battery according to its correct polarity.
• Remove the battery during long periods without use.
• Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals.
  ecover the battery with tape before disposal.
  *This will prevent battery fluid leaks that may cause fire and/or other damages.

Warning

• Place the battery out of children and infant reach.
  *If battery is swallowed, contact a doctor immediately.
• If battery fluid leaks onto user, quickly rinse off area using water.
• If battery fluid gets into eyes, do not rub your eyes. Quickly rinse it with water and consult a doctor immediately.
• May result in vision impairment or blindness.

When the battery is in use, do not do the following operations.

• Do not hold or store with metal objects (such as a necklace or a watch).
• Do not mix new and old batteries.
• Do not pull battery apart battery or throw it into water and/or fire. Battery fluids may cause a fire.

Attention

Do not use the heated seat or warm dryer temperature for an extended amount of time.

• Extended use may result in burns.

While using this product, make sure that the skin is in contact with the seat sensor area. Otherwise, product may not operate correctly.
*Children and smaller individuals may have trouble staying in contact with sensor area.

Do not spray urine in the direction of the bidet nozzle.

• Doing so may result in blockage to the bidet nozzles and cleaning area.

Do not use your old hose component.
Use the one provided with your product. Anything else connected to the older hose may need to be replaced.

• Risk of water leakage and/or property loss/damage.

In case of sudden power failure, remove the power plug and close the angle valve to prevent water leakage.

• Risk of water leakage and/or property loss/damage.

Avoid direct sunlight or heat.
*Risk of product discoloration.

Do not supply electricity with an external switch. le: connecting the universal part to a timer switch.

• Run the risk of issues caused by improperly resetting the thermal breaker.

When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed, be sure to fasten it with force.

• Risk of water leak

Pull out the power plug when the product is in disuse for an extended amount of time. Make sure to shut off the water and remove the water inside the product.

• Risk of fire, leaks, and product damage.

*** When storing or transporting in cold climate, make sure to remove all water from the unit. Product may crack and other damages may occur due to freezing water.
Risk of fire, leaks, and product damage.

Installation

Tools required for installation

Required tools

Required tools for installation. Please have these tools prepared prior to installation.

• Drill (Dia. 0.24in)

• Silicone gun

• Teflon tape

• Knife

• Marking pen

• 0.91 – 0.98 in (Spanner model varies for different pipes)

• +- Sewdriver

• Measuring tape

• Measuring cup

Item list (Confirm that all below items are inside the box)

Intelligent toilet(1 set)

|

T-valve( 1 pc)

|

Two AAA Battery

---|---|---

Remote controller set( 1 set)

(holder 1 pc, screw 2 pcs)

|

Wax Ring(1 pcs)

| Installation Book & User Manual

Sealing Flange

|

Mounting accessory kit(2 pcs)

| Mounting Template

⋇ Please confirm all the aforementioned items are inside the package.
If there are any omissions, please contact our customer service.
⋇ illustrations above are for references only, Actual objects may look different in person.
⋇ XWe provide you with 2 pcs of conversion nut, each different versions.
Please select according to your plumbing requirements.

Before you Install

Water pressure check, dimensional drawing

Confirmation of water pressure

• The minimum dynamic operating water pressure is 35 psi, and the maximum static water pressure is 108 psi.

Determination method for minimum water flow

Open the angle valve for water supply.
The measured water flow for 10 seconds should exceed 1.76GPF.

⋇ If the above conditions cannot be met, the best flushing effect cannot be achieved and an additional booster pump is required to increase the pressure.

Confirm dimensions of product with installation space

• Side view

• Front view

• Top view

Installing your product

Install your unit using the following steps

1. open the box right side up
   Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.

2. Mark your drainage hole with a cross
   Cardboard installation

   • Align cardboard with the centerline of drain outlet;
   • Draw contour line according to cardboard;

3. Mounting bracket installation

   • Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.

4. Install the ceramic body, water supply hose, T-valve

5. Place the wax ring on the drain hole at the bottom of the ceramic.

6. Install sealing flange into drain outlet.

7. Install ceramic toilet on corresponding position according to contour line.

8. Put the screw through the fixing sleeve and then install it through the holes(on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool.

9. Put the decorative cap on the fixing sleeve.

10. Attach the flush water hose to the T -valve and tighten.

11. Attach the clean water hose to the T-valve and tighten.

12. Connect the T -valve to the water supply and tighten.
    Use gasket to prevent water leakage.

13. Finish installation.

14. Installing the remote

15. Drill two 6mm(0.24 inch) diameter holes on the wall (about 1.77 in deep)

16. Knock the anchors into the hole with a hammer.

17. Secure the holder with anchors.

18. Use the screws to secure the holder to the wall.

19. Remove the battery cover from the backside of the remote to install batteries

20. Once finished, remote is ready to be placed in its holder.
    Detailed steps shown in the diagram below: * Please use proper mounting tools for special wall surfaces(such as wood, HDF, etc.)
    ⋇ The remote control holder should be installed away from the bidet’s spray trajectory.
    ⋇ The remote control holder should be installed within reach when seated on unit.
    ⋇  Make sure there is nothing to block the transmission between the toilet and its remote.

Steps:

6. Installing and replacing the battery box
   Install and replace the emergency flushing battery

7. Reach into the bottom of the toilet cover and lift the cover upward firmly;

8. Remove the battery cover by unscrewing the screw with a crosshead screwdriver;

9. Replace the new battery, shut the battery cover, and tighten the screw with a crosshead screwdriver;

10. Place the toilet cover to the flat position and press down to fix the cover.
    ⋇ Please confirm the battery’s positive and negative poles. Please do not charge, disassemble, fire the battery, or mix with used batteries or different kinds of batteries to avoid liquid leakage or explosion.
    ⋇The battery box has a moisture-proof function. Please ensure that the set screws are screwed in place to achieve a good seal effect.
    ⋇ If the battery needs to be replaced, it is recommended to contact your local dealer to have it replaced by specialized personnel.
    When delivered from the factory, the battery has been installed in the battery box.

11. Testing water flow

12. Open the water supply angle valve to maximum as shown in the figure.

13. Confirm various connecting parts are not water leaking.

• In case of water leaking, unfasten the nuts again and install them again. 8. Connecting power

  1. Connect to the grounding.

  2. Plug in AC 120V power plug.

  3. Check to see if the power is on.

  4. Check to see if the power light is on. If not, push the reset button.

  5. Once the power light is on, the toilet will run its initial diagnostic: lights will turn on, cleaning nozzle will extend, the motor will begin to run and water will run through the system. Once the light is off, the self-diagnostic is complete.

  6. Powered on: Press and hold the knob for 3 seconds to enter the standby mode.

Testing the product

(Test whether the functions of the buttons on the remote controller and the knobs on the side of the body are normal)

• Are all the functions working properly?
  Rear Wash, Front Wash {Including water pressure & nozzle position adjustment), Heated Dryer, Water & Seat temperature Adjustment, Nozzle clearing, Anion Deodorization, Remote control.
  All functions listed above should be tested.

• Checking Rear Wash
  Please use your hand to hold the seat sensor area, turn the knob forward or press the “Rear Wash” button on the remote controller, and use your hand to cover the front of the washer to block the flow of wash water to avoid spraying water on your body or clothing.

Matching your remote control code

*When the product leaves the factory, the remote control and the product are connected, if the remote control went failure, please re-connect the code as following methods.

1. Unplug the product’s plug, press the stop ket for few seconds until the level light is flickered.

2. Plug the attaching plug when the remote control get closer to the product.

3. The level light stops flickering, and then it is lighted on.
   All the level light (red) is lighted on

4. At the time, the remote control and product is re-connected.

Function Explanations

*When starting up, short press the knob to send ceramic flushing command when there is no function.

Auto flush

When the seat sensor no longer detects a user, it will automatically flush.
The toilet will only flush once.

Emergency Flushing

When the product is not powered-on, short press the “Flush/Stop” button on the side of the product or slightly touch the “Foot Touch” button. It can achieve emergency flushing function.
⋇If the above operation does not work, you need to replace the battery or contact your local dealer.

Dryer flush

Press the “Dryer” button.
The warm air function is activated and a flush is performed.

Kick flush
Tap the “Kick Button” with your foot for easy, manual flushing.
Note that the “Kick Flush” function is not available when user is sitting on the toilet seat.

UV sterilization
After leaving the seat, it will run automatically.
Operate it automatically when leaving seat.
The cleaning spout will back to position, and the UV function will be activated after 1 Os, and it is working for 3mins.
After seating, the UV function will stop and the indicator will go out.

⋇Ultraviolet lamp device is installed on smart toilet.

Night light
Automatic operation according to ambient light.
When the night light is turned on, the night light can be turned on / off automatically through the change of external light intensity. When there is strong light, the night light will turn off automatically, and when the light is weak, the night light will turn on automatically.

Auto deodorization
The function runs automatically.
After the seat is seated, the deodorization fan is automatically turned on, and the deodorization is turned off 3mins after leaving the seat.

Digital display
When setting different functions of temperature adjustment, the corresponding function indicator lights up.

User-friendly Design

• Slow-closing lid/seat
  Preserve your toilet’s life and allows you to close the lid/seat silently.

• Water purification
  Equipped with dedicated filter to ensure your bidet will only spray clean, filtered water.

• Damper
  The product has installed the damper which provide the toilet cover and toilet seat with a buffer function, to achieve the mute effect.

• 8 Layers of safety
  8 different built-in safety features to protect the user and product.

• Memory mode
  After power failure, water temp, water pressure, seat temp, and wand position are all restored to mid-range after power failure. Night light is turned on by default after power failure.
  On I off, keep the last memorized setting state.

• Self-cleaning Nozzle
  The washer can automatically clean, keeping bacteria and stains away.

• Pre-flush
  After seating, the product will flush once towards the seat to ensure that the seat wall is moistened. antibacterial Seat
  Antibacterial material is used for the seat.

Maintenance

Regular maintenance is required to ensure normal use

Note

• Cut off the power and water supply before maintenance.
• Direct water wash to the entire product is prohibited.

WARNING

Do not spray water or detergents on the toilet, remote control or the power cord. Doing so may cause electric shock or fire.

Maintenance during Winter Season
During winter season, the water inside may freeze after long periods of storage and non-usage. Please take measures to prevent.

Note

• Before connecting the product to the water supply and electrical outlet, allow it to defrost for 30 mins in a warm indoor environment.
• In cases of extreme cold/freezing/nozzle stuck in place, wrap the water input line with a warm towel. Never pour hot water or use a hot dryer directly on the toilet.

Specifications

10.57GPF/min
Maximum pressure| 108psi (static state)
Toilet| Flush type| Tornado flush
Rough-in| Rough-in 12in
Flushing| Heating type| Instant heating
Washing temp range| OFF/93.2 “F- 102 .2 “F (4 levels)
Safety system| Butterfly thermostat, thermal fuse, flow sensor
Dryer| Dryer temp range| OFF/ 95″F -131″F (4 levels)
Dryer air speed| >4m/s
Safety system| Thermal fuse, bi-metal
Heated seat| Heat temp range| OFF/ 93.2″F- 104 “F (4 levels)
Safety system| Thermal fuse
Power cable length| Appx. 34.25 in

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>