homewardbath GS08T Control Panel, Steam Generator Wi-Fi Keypad User Manual

homewardbath GS08T Control Panel, Steam Generator Wi-Fi Keypad

Product Information

The product is a control panel model GS08T. It comes with a 2-prong plug for the adapter (A), an adapter power supply cord with a bare wire end (B), an adapter power supply cord with an adapterplug end (C), a 120/240v to 12v adapter (D), a Bluetooth connection wire from the adapter (E), and a Bluetooth control box connection wire (F).

Product Usage Instructions

1. Step 1: Connect the bare wire end of the adapter power supply cord (B) to the 2-prong plug (A).
2. Step 2: Connect the adapter plug end of the adapter power supply cord (C) to the 120/240v to 12v adapter (D).
3. Step 3: Connect the Bluetooth connection wire from the adapter (E) to the Bluetooth control box connection wire (F).
4. Step 4: Connect the 2-prong plug (A) to a 110v power source.

To power on the steam generator:

• A. If the steam generator is in standby state, touch the button to switch it on. If it has been locked by a password, enter the password to activate the keypad.
• B. If the steam generator has a preset open time, it will automatically power on with the temperature and working time set by user 1 when the preset open time is reached.
• C. The steam generator can also be powered on using the APP.

Please note the following:

1. The keypad is in capacitive touch mode. Water mist on the screen surface may affect the touch effect. Normal operation can be resumed after removing the water mist.
2. The keypad surface is made of glass. Do not rub it with hard objects and pay attention to the front protection.

(A) 2-Prong Plug for Adapter (B) Adapter power supply cord, bare wire end (C) Adapter power supply cord, adapter plug end (D) 120/240v to 12v Adapter (E) Bluetooth Connection wire from the Adapter (F) Bluetooth Control Box connection wire

Wi-Fi Power Supply Assembly Steps

• Step 1. Connect the bare wire end of the adapter power supply cord (B) to 2-prong Plug (A).
• Step 2: Connect the adapter plug end of the adapter power supply cord (C) to the 120/240v to 12v Adapter (D).
• Step 3: Connect the Bluetooth connection wire from the Adapter (E) to the Bluetooth Control Box connection wire (F).
• Step 4: Connect 2-Prong Plug (A) to the 110v power source.

Interface Introduction

ATTENTION

1. the keypad is in capacitive touch mode, water mist on the screen surface will affect the touch effect. Normal operation can be resumed after water mist is removed;
2.  The keypad surface is made of glass. Do not rub with hard objects, and pay attention to the front protection.

FUNCTION

1. Steam
2. Bluetooth Music
3.  Light
4. Chroma light
5. WIFI
6. Clean (can be operated on APP)

POWER ON

• A. When the steam generator is in the standby state, touch the button to switch on the steam generator. If the steam generator has been locked by password, the user should enter the password to activate the keypad.
• B. If the steam generator preset open time, when preset open time reaches, the steam generator powers on with TEMP. and working time by user 1 set automatically.
• C. Power on by APP
• When the system is powered on, a backlight of the power on/off button lit.
• When the steam generator is connected to Wi-Fi, the WIFI icon shows on the display window.

POWER OFF

• When the steam generator is on, touch the button to switch off the steam generator. The control panel shows a real clock if the preset clock function is, otherwise, the control panel will be a black screen.
• When the preset working time is reached, the steam generator power off automatically (the steam generator power off in 2 minutes after the steam function stop).
• Power off the steam generator by APP.

WATER DRAIN

• Water drains for 5 minutes automatically in 30minutes from the steam generator shuts off.
• When a steam generator is on and the steam function still not be activated, touching the button to drain water for 10 minutes manually

BLUETOOTH MUSIC

• when the control panel is powered on, we open the Bluetooth on the mobile connect the Bluetooth name “sauna”, and touch the button to switch on/off Bluetooth music as shown in picture 9. At this time, we can display music from the mobile.
• When Bluetooth music works, touch the button and  to switch the song you like. When Bluetooth music works, touch the button to adjust the Volume setting range is Oto 15dB.
• When the steam generator is connected to a Bluetooth music box, we can see an icon shown on the keypad window. When the mobile is connected with Bluetooth music of our steam generator, we can see icon shows on the keypad window.
• Bluetooth stops connection after 1 second from the steam generator power off. When the steam generator restarted after 10 seconds, we had to reconnect the mobile’s Bluetooth, The Bluetooth name is “SAUNA”.

LIGHT

• When the steam generator is on, touch the light icon on the keypad to power on/off the normal light.
• Light can be powered on/off by APP.

CHROMA

• When the control panel enters into the chroma light interface as in picture 10, choose a light color we like on the color circle. Light will be powered off when we move the bar to the OFF state of the color circle.
• The icon in the circle shows the current color of the light
• We could change the light color by APP.

STEAM

• When the steam generator is on, touch the steam button as shown in picture 3 to start steam, touch this button again to stop steam.

Steam temperature setting

• Touch the display position of ambient temperature and the corresponding scrolling window will pop up. Slide up and down to adjust the steam temperature we like. Click the corresponding temperature value to set the steam temperature. The screen displays the ambient room temperature after that.
• Steam temperature setting range is 77-154℉(equal to 25-68℃， step is 1℃) if ECO mode still not be activated.
• If ECO mode is activated, we can see the icon on the keypad screen. Steam temperature setting range is 77-122℉（equal to 25-50℃）.

Steam time setting

• Touch the position of the time display 8 : 0 0 to pop up the scrolling window of the time setting. Slide up and down to adjust to the required working time. Click the corresponding time parameter to complete the setting of steam time and return to the time display window.
• The time setting range is from 30mins to 23 hours on the control panel.
• The time setting range is from 1minute to 20 hours on the APP.

USER PREFER MODEL SETTING
In the user model interface as in picture 6, Click the 1 icon to pop up the dialog window as shown in picture 8: select” Yes “to set parameters with this user, and select” No “to exit the setting interface. The user preferred mode setting will be valid when the steam is on. If Steam is off, the user can’t set the user prefer mode.

User parameter modification
On user preferred mode setting interface, touch the area on the right of the corresponding user information and the dialog box pops up as shown in picture 7. By sliding the parameters up and down in the temperature area or time area, adjust the parameters to the middle position of the window and touch the “Set” key to save the user information. Touch “Exit” to give up the setting.

PRESET OPEN TIME
Touch the icon to enter the setting interface, and touch the icon on the right of” Working Mode “to enter the appointment setting interface as shown in picture 12.

• A. Setting of startup Time: Touch the time to boot. 10:30 startup time area to pop up the sliding window and select the
• B. Select the mode of appointment: Select the required mode of appointment by touching the corresponding Settings DAY SUN MON TUE WED THU FRI SAT O N E RE P . After completing the following actions and touching the “Set” key, the parameters of appointment can be valid. Give up this operation by touching “Exit”. Touch the two buttons above mentioned to go back to the main setting interface.
• C. When the appointment open time is reached, the system will start up automatically and steam will be turned on. Steam temperature and working time using the parameters of User 1.
• D. You can modify the default steam temperature and working time on the APP.

REAL-TIME CLOCK SETTING

• Under the setting interface, touch th e button on the right of the interface as shown in Figure 13. Real-time clock to enter the clock setting
• Time calibration: touch the parameters to be adjusted, such as year, month, day, hour, and minute; The corresponding scroll setting bar will pop up, and the corresponding parameters will be found and clicked. Time calibration can be completed by setting the above parameters and touching the Set key. The time can be synchronized through the APP on mobile.
• Clock display: Touch the display area Show real time to choose whether to display the clock function after shutdown. When the option is checked, the system shutdown displays the clock and the panel backlight is correspondingly lowered when the clock is displayed

TEMPERATURE UNIT SWITCH

• On the Settings interface, you can switch temperature units by touching or the temperature is 45℃ or 113℉.

SAFETY LOCK

• Touching the Safety lock on the setting interface, the pop-up dialog box shown in Figure 14, we can type a number password and touch “OK” to save the password, if the user forgets the password, the user can type the password 2580 to enter into the system.
• After we set the password, when we touch the power on/off button to start the system, a password dialog window will pop up as in picture 2. After entering the correct password, you can enter the control interface. Power on by appointment open time and APP are not controlled by the safety lock. The system can enter into the main setting interface directly. We can close the safety lock function on setting interface by touching the icon

COMMERCIAL MODE AND RESIDENTIAL MODE

• In commercial mode, the steam working time is 8 hours and the steam temperature is 45℃ or 113℉.
• in residential mode: the default steam working time and steam temperature are the same as the last time setting. if the time user changes steam temperature and working time, data will be saved for next time using.
• When the on the right of memory mode is on, the system is in residential mode, when it shows , the system is in commercial mode.

ECONOMY MODE

• We can switch on/off economy mode on setting interface. When economy mode works, the maximum steam temperature is 50℃ or 122℉, at the same time, we can see the icon shown on the display window.

WIFI MATCHING

• On the setting interface, touch on the right side of the ” WIFI Match ” item to pop up the dialog box, after selecting ” Yes “, the WIFI box will enter the pairing state, and the phone needs to operate according to the APP usage requirements. LED on WIFI box flashing when it is in paring state. If paring is unsuccessful in 2 minutes, the system will quit the paring state automatically. Select “No” to give up the pairing operation.

RESTORE FACTORY MODE

• On the setting interface, touch the icon on the right of Factory Setting to pop up the dialog box, and select ” Yes “to restore the user data from the Factory setting. Select “No” to give up the operation.

Troubleshooting

• When the system failure, we can see the icon is shown on the upper left corner of the main setting interface, touch this icon will pop up the dialog to show you the problem and solution. pressing “Ok” to see the error code. pressing “Exit” to Exit the prompt window. The problem and solution message will be shown as follows:

TECHNICAL PARAMETER

Rated Working conditions and characteristic

Rated voltage| AC240| Frequency| 50/60Hz
Rated current| | |
Insulation resistance| | |
Load parameters

Loads| Rated voltage| Frequency| Rated power| Other
Steam machine| AC240V| 50/60Hz| 4.5-18KW| –
Light| AC12V| –| <3W| –
Solenoid valve| DC12V| –| 5W2| –
Color light| DC12V| –| 5W| –
Loudspeaker| –| –| 8Ω/5W2| –

APP OPERATION

1. Download the APP on mobile Scan QR to install the APP. Enter the download interface as shown in the pictures, click“download”, and choose“regular download” to download the APP on mobile.

2. User registration and sign-in
   Click the APP logo“Smart Life” to enter into the login interface as the picture shows, if it’s a first-time login, need to register a new user account as a guide.

3. Adding a steam generator to the APP

4. First, we should get the WIFI box in the matching state by operation below:
   Method: On the setting interface, touch on the right side of ” WIFI Match ” item to pop up the dialog box, after selecting ” Yes “, the WIFI box will enter the pairing state, LED on the WIFI box will flash when it is in the paring state. If paring is unsuccessful in 2 minutes, the system will quit the paring state automatically. Select “No” to give up the pairing operation.

5. Adding steam generator on APP
   The first time use it, you have to add your steam generator to the device list. When the WIFI box is in a matching state, please enter the WIFI password on the APP as picture below: click “confirm” to add the steam generator to the APP and enter it into the product operation interface.

6. The operation interface of the steam generator on the APP

7. Steam temperature Setting

8. Working Time Setting

9. Appointment Setting

10. Chroma Light

11. Normal Light and Aroma
    Steam function on, click on the “light” button switch on/off the normal light. When the steam function is on, click the aroma button to switch on/off the aroma function.

12. Setting

13. Parameter Settings

14. Share device

Documents / Resources

| homewardbath GS08T Control Panel, Steam Generator Wi-Fi Keypad [pdf] User Manual
GS08T Control Panel Steam Generator Wi-Fi Keypad, GS08T, Control Panel Steam Generator Wi-Fi Keypad, Panel Steam Generator Wi-Fi Keypad, Steam Generator Wi-Fi Keypad, Generator Wi-Fi Keypad, Wi-Fi Keypad, Keypad
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>