AUKEY TM-20 Track Mate 2 Smart Bluetooth Tracker User Manual

USER MANUAL

Track Mate 2

Using “Find My” App

1. Turn on the product

Long press the product button for 5 seconds and the device beeps and turns on.

2. Pairing

• Open Apple “Find My” app
• Bring the product close to your iPhone, tap “Items” >> “Add New Item” >> “Other Supported Items”
• For the device named as TM-20, select “Connect”
• Enter “Custom name” to label the product and choose an emoji for it
• Consent to link the product with your Apple ID
• Tap “Finish” to complete the pairing process

3. Enable lost mode

• Open Apple “Find My” app. Tap “Devices” at the bottom of the screen and select the device you wish to put into Lost Mode.
• Click “Enable” under “Lost Mode” section .
• Proceed with the on-screen prompts and click “Continue” to enter your contact number or email.
• Tap “Next” to confirm contact information. Select “Enable” again to complete settings.

4. Remove the product

• Open “Find My” app, click “Devices” at the bottom of the screen and choose your device’ s name.
• Scroll to “Remove Item” at the bottom of the list and tap “Remove” to complete the operation.

Note: After removing the product in the app, the product will not shut down but still in the pairing mode. If there is no re-pairing within 10 minutes, it will exit the pairing state.
To pair the product, press the button once. The product will ring and indicate it can be re-paired with the app.

Using the Product

1. Turn on
   Long press the product button for 5 seconds, the product beeps and turns on.

2. Check the product status
   Double click the product button and the product beeps, indicating that the product is working. If it does not beep, it means the product is turned off. Press and hold the button for 5 seconds to turn on the product.

3. Re-pairing status
   After removing the product in the app, the product will beep. It will not shut down but still in the pairing mode. If there is no re-pairing within 10 minutes, the product will exit the pairing state.
   To pair the product, press the button once. The product will ring and indicate it can be re-paired with the app.

4. Reset
   Turn on the product and double-click the button, the product will beep. Then long press the button for about 10 seconds, the product will beep at the 2nd second and 10th second. Release the button to complete the factory reset.

5. Turn off
   Quickly press the product button 5 times within 2 seconds, the product will beep and turn off.

Product Care and Precautions

1. Please read the user manual prior to operation, or it may lead to loss, improper use and damage to the equipment.
2. Do not expose the product to humid environments or soak it in liquids.
3. Do not drop, strike, disassemble or attempt to repair the product on your own.
4. Do not leave the product in extremely hot or cold place for a long time.
5. Do not leave the product in a vehicle, as the exposure to high temperatures from sunlight may cause damage to the product.
6. Stop using the product immediately and contact the support center for assistance in cases of any defects or malfunctions in the product.

Warning

The product is designed for safe operation in non-tropical climates and at altitudes not exceeding 2km above sea level.

Warranty & Customer Support

For questions, support, or warranty claims, please contact your seller directly.

Specifications

FCC STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement, the device can be used in portable exposure condition without restriction.

Follow Us to Unlock More about AUKEY:

@AUKEYofficial
 @aukeyofficial
@AUKEYofficial
AUKEYofficial

Model: TM-20

Aukey Technology Co., Ltd.
www.aukey.com | support@aukey.com
Room 116, Kangli Information Valley Building, Shanglilang Community,
Longgang District, Shenzhen, Guangdong, 518111, China

Made in China

Documents / Resources

| AUKEY TM-20 Track Mate 2 Smart Bluetooth Tracker [pdf] User Manual
TM-20, TM-20 Track Mate 2 Smart Bluetooth Tracker, Track Mate 2 Smart Bluetooth Tracker, Smart Bluetooth Tracker, Bluetooth Tracker, Tracker
---|---

References

• AUKEY Official | Unlock More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>