VOLVO 39848485 Fender Extension Kit Installation Guide

VOLVO 39848485 Fender Extension Kit

Product Information

Specifications

• Part Numbers: 39848485, 39790113, 39848665, 39790091, 39848647, 39848629, 39848611, 39848593, 39848575, 39848557, 39848539, 39848521, 39848503, 39848467, 39848449, 39848413
• Designation: Isopropanol Primer
• Equipment Part Numbers: 1161721, 1161727

Product Usage Instructions

Installation Precautions

1. Ensure the car maintains a temperature of 20 degrees C during installation.
2. Avoid washing the car for 48 hours after installation.

Removal Instructions

1. For vehicles with Parking assistance pilot
2. Remove the marked part using pliers.
3. Remove the screws and the marked part.
4. Fold the wing liner aside.
5. Release the catches and loosen the indicated component without removing it.
6. Use an interior trim remover to remove the marked part (not to be reused).

Accessory Installation
Note: Make sure the template is correctly located.

1. Hold the component in the position shown.
2. Make a hole using the indicated tool.
3. Remove the Special Tool after installation.

FAQ

• Q: Can I wash the car immediately after installing the fender extension?
  

  • A: No, it is recommended to avoid washing the car for 48 hours after installation.

• Q: Can I reuse the parts removed during the installation process?
  

  • A: No, the removed parts should not be reused.

Fender extension (vehicles with variant code UF06) – XC60 2020 – Vol…

https://accessories.volvocars.com/en- ca/InstallationInstruction/Docume…

Installation Instructions

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

• Instruction No Version Part. No.
• 31454899 1.0 39848485, 39790113, 39848665, 39790091, 39848647, 39848629, 39848611, 39848593, 39848575, 39848557, 39848539, 39848521, 39848503, 39848467, 39848449, 39848413

Fender extension (vehicles with variant code UF06)

IMG-421931

IMG-425895

Information

• Read through all of the instructions before starting installation.
• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.
• Ensure that all tools stated in the instructions are available before starting installation.
• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

Note!
If a pending accessories installation include the removing and replacing of the bumper, this installation should be carried out first.

• When installing, the car must retain a temperature of 20 degrees C.
• After installation, the car must not be washed for 48 hours

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

1. Used for focused component, the component with which you will do something.
2. Used as extra colors when you need to show or differentiate additional parts.
3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.
4. Used when the component is not fully removed from the vehicle but only hung to the side.
5. Used for standard tools and special tools.
6. Used as background color for vehicle components.

Removal

Vehicles with Parking assistance pilot

• Remove the marked part.

• Use: Pliers

• Remove the screws.

• Remove the marked part.

• Remove the screws.

• Remove the marked part.

• Fold the wing liner aside.

• Release the catches.

• Loosen the component indicated. Do not remove it.

• Remove the marked part.

• Use: Interior trim remover

• The part is not to be reused.

All vehicles

Accessory installation

Note!
Make sure that the template is correctly located.

• Hold the component in the position shown.
• Make a hole, using the tool indicated.
• Remove the Special Tool.

Note!
Make sure that the template is correctly located.

• Hold the component in the position shown.

• Make a hole, using the tool indicated.

• Remove the Special Tool.

• Clean the surfaces.

• Allow to dry.

• Use: 1161721, Isopropanol

• Remove the screw.

• Install component that comes with the accessory kit

• Reinstall the screw.

Note!
Note the position.

Install component that comes with the accessory kit.

Note!
This step is easier with two people.

1. Hold the component in the position shown.
2. Use: Masking tape

Remove the marked part.

Note!
Note the position.

Install component that comes with the accessory kit.

Note!
This step is easier with two people.

1. Hold the component in the position shown.
2. Use: Masking tape

Remove the marked part.

• Apply a thin layer of primer.

• Allow to dry for at least 5 minutes but not more than 30 minutes.

• Use: 1161727, Primer

• Remove the tape.

• Apply a thin layer of primer.

• Allow to dry for at least 5 minutes but not more than 30 minutes.

• Use: 1161727, Primer

• Remove the tape.

Note!
Make sure that the template is correctly located.

• Hold the component in the position shown.

• Make a hole, using the tool indicated.

• Remove the Special Tool.

• Clean the surfaces.

• Allow to dry.

• Use: 1161721, Isopropanol

Note!
Note the position.

Install component that comes with the accessory kit.

Note!
This step is easier with two people.

1. Hold the component in the position shown.
2. Use: Masking tape

Remove the marked part.

• Apply a thin layer of primer.
• Allow to dry for at least 5 minutes but not more than 30 minutes.
• Use: 1161727, Primer
• Remove the tape.

Note!
Note the position.

Install component that comes with the accessory kit.

Note!
This step is easier with two people.

1. Hold the component in the position shown.
2. Use: Masking tape

Remove the marked part.

• Apply a thin layer of primer.
• Allow to dry for at least 5 minutes but not more than 30 minutes.
• Use: 1161727, Primer
• Remove the tape.

Note!
Note the position.

Install component that comes with the accessory kit.

Note!
This step is easier with two people.

1. Hold the component in the position shown.
2. Use: Masking tape

Remove the marked part.

• Apply a thin layer of primer.

• Allow to dry for at least 5 minutes but not more than 30 minutes.

• Use: 1161727, Primer

• Remove the tape.

• Fold the protective film forward

• Vehicles with Parking assistance pilot

• Remove the marked part.

• The part is not to be reused.

All vehicles

Note!
Note the position.

Install component that comes with the accessory kit.

• Caution!
  Pull carefully.

• Note!
  Press and apply pressure to the part over the tape for at least 20 seconds.

• Note!
  Ensure that the tape is fixed to the surface.

Remove the protective film.

• Install component that comes with the accessory kit.

• Secure the template with tape.

• Use: Masking tape

• Fold the protective film forward

Note!
Note the position.

Install component that comes with the accessory kit.

• Caution!
  Pull carefully.

• Note!
  This step requires the aid of another technician.

• Note!
  Adjust the position of the components to create even spaces.

Remove the protective film.

• Remove the screw.

• Remove the marked part.

• Reinstall the screw.

• Caution!
  Pull carefully.

• Note!
  Press and apply pressure to the part over the tape for at least 20 seconds.

• Note!
  Ensure that the tape is fixed to the surface.

• Remove the protective film.

• Fold the protective film forward

Note!
Note the position.

Install component that comes with the accessory kit.

• Caution!
  Pull carefully.

• Note!
  Press and apply pressure to the part over the tape for at least 20 seconds.

• Note!
  Ensure that the tape is fixed to the surface.

Remove the protective film.

• Install component that comes with the accessory kit.
• Secure the template with tape.
• Use: Masking tape

Fold the protective film forward

Note!
Note the position.

Install component that comes with the accessory kit.

Caution!
Pull carefully.

Note!
Press and apply pressure to the part over the tape for at least 20 seconds.

Note!
Adjust the position of the components to create even spaces.

• Remove the protective film.
• Fold the protective film forward

Note!
Adjust the position of the components to create even spaces.

Note!
Note the position.

Install component that comes with the accessory kit.

• Caution!
  Pull carefully.

• Note!
  Press and apply pressure to the part over the tape for at least 20 seconds.

• Note!
  Ensure that the tape is fixed to the surface.

Remove the protective film.

• When necessary, carry out the following instruction.

• Remove the screws.

• Fold the wing liner aside.

Note!
Adjust the position of the components to create even spaces.

Loosen the screws.

Fold the wing liner aside.

Note!
Do not loosen the bolts more than one turn.

Note!

Adjust the position of the components to create even spaces.

Installation
Reinstall the removed parts in reverse order.

Accessory installation
Repeat the steps when installing accessories on opposite side.

Fender extension (vehicles with variant code UF06)- 31454899 – V1.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>