PROFECO 77414 Electric Weed Burner Instruction Manual

77414 Electric Weed Burner
Instruction Manual

77414 Electric Weed Burner

Declaration of conformity

|
---|---

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.Save all warnings and instructions for future reference.
SAFETY WARNINGS
When using the machine, always observe the enclosed safety warnings as well as the additional safety warnings.
The following symbols are used throughout this manual:
** LDenotes risk of personal injury or damage to the machine
Explanation of the symbols
Warning! Read the user manual.
Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.
Indicates electrical shock hazard.
Do not expose to rain!
There is a fire hazard.
Remove plug from the mains immediately if the cable is damaged or cut.
Caution, hot surface! Risk of burns dueto hot surfaces! Do not touch!
Always remove the plug from the socket, when appliance is not in use, hen changing nozzles or when servicing or cleaning.
** Electric power tool, protection class II.

Safety instructions

This appliance should not be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge.
Children shall not play with the appliance.
Disconnect the unit from the power supply and allow it to cool before cleaning, maintenance or storage.
Protect electrical parts against moisture. Do not immerse in water or other liquids during cleaning or operation to avoid electric shock. Never hold the appliance under running water.
A fire can occur if the appliance is not handled with care.
Caution when using the device near combustible materials. Do not point to the same location for an extended period of time.
Do not use in the presence of an explosive atmosphere.
Heat can be passed to combustible materials which are hidden.
After use, place the appliance on the stand and allow it to cool down before it is packed away.
Do not leave the appliance unattended while it is in operation.
Additional safety instructions
** When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before attempting to operate this product and save these instructions.
Before using the appliance**

• Check the following:
  • Make sure the voltage of the appliance corresponds with the power voltage;
  • Are the mains lead and the mains plug in a good state: strong, without ravels or damages.
• Caution is advised when using long extension cables.
• Do not use the appliance under moist circumstances;
• The metal mouthpiece gets hot. Watch out and do not touch the metal mouthpiece;
• Prevent damage of the heating element. Do not lock or block the mouth piece;
• Do not leave the appliance when switched on;
• When in operation do not point the device at people or animals.
• Never look into the hot air nozzle.
• Do not use this device in rain or damp surroundings, or near explosive or flammable products.
• Do not use the device on or near very dry spots to avoid fire.
• Always remove the plug from the socket when not using the device, when replacing the nozzles or during maintenance of the device.
• Do not point the device at the same place for longer periods of time.
• Do not hold the device too close to the surface about to be worked on as the device can overheat.
•  Pay attention to the direct / indirect workspace as the heat can ignite flammable materials, which are close by but not necessarily in view.
• Do not allow the hot parts of the device to touch the cord or other flammable materials.
• The device should always be clean, dry and free of grease and oil.
• Do not use the appliance for purposes other than for which it is intended.
• Never run while holding the unit in your hands.
• Always leave the cable to the rear, away from the unit itself.

This appliance operates at a temperature of 600 degrees without visible signs of this temperature (no flames), still there is a chance of fire risk. Watch out for the hot air stream from the mouth piece. This air stream can cause burns.
There is a risk of fire if the appliance is not used with care, so please take note of the following:

• Please be cautious with the device when you are near flammable materials.
• Never leave the appliance unattended when it is switched on.

When operating the appliance

• If you are going to use the appliance, vapours and gas can be released during a short time. This can be harmful for your health. Asthmatics can suffer hindrance of it.
• Before connecting the plug to the mains voltage you have to check if the switch is in position “0”.
• Keep the mains lead always away from the mouthpiece of the hot air gun.
• Keep children and animals away from the appliance if you are using it.
• Keep all parts of the body away from the metal heating head. Do not touch it before it is cooled down.
• Carry the appliance by the handle when the metal heating head is cooled down.
• Hold the appliance by insulated gripping surfaces only, because the metal heating head may contact hidden wiring or its own cord.

Immediately switch off the appliance when:

• **** Plug and/or cable are defective or damaged;
• The switch is defective;
• You smell or see smoke caused by scorched insulation from the hot air gun.

ELECTRICAL SAFETY

** Always check that the power supply corresponds to the voltage on the rating plate.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely.
Inadequate extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and the connection has to be kept dry and off the ground.
It is recommended that this is accomplished by means of a cord reel which keeps the socket at least 60 mm above the ground.
Connecting to power supply**
This product is designed with a cord retainer (8) that prevents the extension cord from being pulled loose while using.
Always use cord retainer to properly attach extension cord to the machine. Failure to use cord retainer may result in damage to the machine and/or extension cord.

• Form a loop with the end of the extension cord.
• Insert loop portion of extension cord through opening and place over cord retainer.
• Slowly pull loop against cord retainer until the slack is removed.
• Plug product into extension cord.

**** Failure to remove all excess cord slack from extension cord retainer could result in plug loosening from receptacle.

DESCRIPTION

(fig. A)
This device can be used as a weed killer, paint remover and lighter for barbecue and fireplace. Use this appliance for the intended purposes only!
Other forms of use can lead to injuries or accidents!

1. On/off switch
2. Hot air nozzle
3. Stand
4. Ventilation openings| 5. Extension handle connection
6. Extension handle
7. Handle
8. Cord retainer
---|---

Nozzles (fig. B)
9. Nozzle for weed control
10. Nozzles for paint removel
11. Nozzle for barbecue/fireplace lighter

Packaging contents

The packaging contains the following components:

• Weed burner
• Nozzle for weed control
• 2 nozzles for paint remover
• Nozzle for barbecue/fireplace lighter
• Extension bar
• Handle

OPERATION

** Always use with caution! Do not cover the ventilation openings during use as it causes a risk of burns! Do not touch the hot nozzle!
Temperature settings
With the temperature switch (6) you can select from two temperature settings.
Setting I 50 °C (venting/ cooling)
Setting II 600 °C
The volume of air in each setting 500 l /min.
To turn on the power**

• Push the switch (1) in position I or position II.

To turn off the appliance

• Push the switch on position 0.

To install the nozzle
The nozzles can easily be pushed over the hot air nozzle. Never touch the nozzles during or immediately after use of the device. The nozzles are very hot.

INSTRUCTIONS FOR USE

Weed burner
Assemble the extension handle:
The extension handle consists of two parts. Connect both parts and attach the extension handle to the device. To attach the extension handle, place the extension bar in the machine and turn the extension handle a quarter turn to the right. Make sure that the extension handle firmly clicks into position.
**** If using the device as a weed killer you must use the extension handle. Hold the weed killer firmly by holding the end of the extension handle.
Ensure the extension handle is firmly fixed onto the device and that the device is turned off.

• Install the nozzle (9) to destroy weeds.
• Insert the plug into the socket.
• Check to ensure the nozzle is not blocked before turning the device on.
• Set the temperature to setting II.
• Allow the device about 45 seconds to warm up.
• To eliminate weeds, hold the nozzle over the weeds for about 5 seconds. During these 5 seconds the cell structure of the weed is destroyed. As a result, the weed dies within a few days.
• It is not necessary to completely burn the weeds, 5 seconds is more than sufficient.
• For an efficient treatment the nozzle should beheld around 0 to 5 cm above the weeds.
• The effects are not visible immediately but will take a while before they can be seen. It ismore of a long-term effect.
• In the case of very leafy plants, the treatment may have to be repeated several times at intervals of 1 1 2 weeks.

Paint removal

The paint removal can be used for various purposes, such as:

• Removing old paint and gloss.
• Removing self-adhesive labels.
• Bonding of PVC labels.
• Removing vinyl wallpaper.
• Fast drying of damp equipment.
• Shrink packaging.
• Defrosting of water pipes.
• Loosening of nuts and bolts.

**** The paint removal is always done without the use of the extension handle.

• Remove the extension handle by pulling out the locking ring and turning the extension handle a quarter turn to the left.
• Attach a desired nozzle (10) onto the device.
• Insert the plug into the socket.
• Check to ensure the nozzle is not blocked before turning the device on.
• Set the temperature to setting II.

Barbecue/fireplace lighter

**** The barbecue and fireplace lighter is always to be used without the extension handle.

• Remove the extension handle by pulling out the locking ring and turning the extension handle a quarter turn to the left.
• Attach the barbecue nozzle (11) onto the device
• Select temperature setting II.
• Place the nozzle under the coal or the wood.
• Ensure that the firelighter is properly positioned
• Insert the plug into the socket.
• Check to ensure the nozzle is not blocked before turning the device on.
• Remove the device from the coals or the wood as soon as it starts to glow
• Now blow hot air into the coals or wood from a distance of around 5 – 10 cm, until the coals or wood is burning properly.
• Doing this will help to avoid damaging the nozzle attachment. Exposing the nozzle to high temperatures for a prolonged period of time could cause the material to melt. Please follow these instructions to achieve long-term enjoyment with the product.
• Switch off the device before removing from the fire.

** Watch Out! To avoid overheating of the barbecue or fireplace do not use the device for longer than necessary.
COOLING DOWN**
With the aid of the stand (2), it is possible to lay down the appliance while it is cooling down.

• Leave device to run for at least one minute in position I.
• Switch off the device.
• Pull the plug out of the socket.
• Allow the appliance to cool down further.
• Remove the accessories.

CLEANING AND MAINTENANCE

**** Firstly let the unit run in position I for at least one minute to lower the temperature to 50 °C.
Disconnect the mains plug from the socket and allow the appliance to cool down completely!
If possible, clean the appliance after each use. Use a damp cloth, on stubborn dirt use a brush. Do not use cleaning agents such as benzine, alcohol, ammonia, etc. These substances attack the plastic parts.

TECHNICAL DATA

Mains voltage
Mains frequency
Power input
Number of temperature settings
Max. air temperature
Air speed
Weight| V
Hz
W
°C
l/min
kg| 77414
230
50
2,000
2
50/600
500
1.0
---|---|---

GUARANTEE

Refer to the enclosed guarantee conditions for the terms and conditions of guarantee.

ENVIRONMENT

Disposal
Your product, accessories and packaging should be sorted for environmental- friendly recycling.
Do not dispose of power tools into domestic waste. According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.
Subject to change; specifications can be changed without further notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>