COMFAST CF-WR758AC Wireless Expander/Repeater Installation Guide
- August 7, 2024
- COMFAST
Table of Contents
COMFAST CF-WR758AC Wireless Expander/Repeater
FAQ
Frequently Asked Questions
- Q: Is the inner pot dishwasher safe?
- A: Yes, the non-stick inner pot is dishwasher safe for easy cleaning.
- Q: Can I use the XYZ-2000 to cook rice?
- A: Absolutely! The XYZ-2000 offers a specific rice cooking mode for perfectly cooked rice every time.
Product Manual
Product Structure
Simple Installation Steps
- Plug in, switch “ON” button on the side, the lights will all light u p
- Wait about 60s, connect WiFi “COMFAST_XXX_2G” or ” COM FAST XXX_SG”
- Click on the WiFi signal “COMFAST_XXX_2G” or “COMFAST_XXX_SG”
- The login interface will pop up, enter the password “admin” in the password box, and click “Set Password”
- Tip: When logging in for the first time, the login interface will pop up automatically.There are two cases when there is no login interface: First, the mobile phone itself does not support pop-up windows; Second, once set, once again enter the interface, you need to manually,Manual entry method: Open the mobile phone browser, enter “192.168.10.1” in the address bar.
- After setting the password for the first time, it will automatically enter the relay scanning page. Set the trunk then choose SSID of the relay, enter the upper routing password and click Save to complete the relay, reconnectConnect to the wireless network to access the Internet, the wireless password is the superior routing password (the expanded signal will be in the superiorAdd “-2G / SG” suffix such as XXXX-2G / SG after the WiFi name.
Warm tips:
- Combine wifi: Turn on this option, it will automatically switch to high-quality band for better performance.
- Sync your device: Turn on this option, the new WiFi will be same as your original WiFi and there is no need to reconnect the extended WiFi anymore.
Operating Mode
- The software has four working modes, including relay mode, bridge mode, AP mode, Routing mode (PPPoE dial-up, static IP, dynamic IP).
- Bridge mode settings: Find and set in the advanced mode.
- AP mode settings: Enter the software management page, click on the AP mode, in order to facilitate management, this The IP address and default gateway entered here should be the IP segment of the superior router, and the IP address cannot be the same as the superior. The router’s IP conflicts. After setting, the device’s WAN port can access the external network through the setting!P address to access the management device.
- Note: Access to external network in AP mode, other mobile devices access the AP’s wirelessly obtained IP address The network segment is allocated by the superior device.@According to the default setting, it is not necessary to set the device-specific intra net IP address;ln this case, you must manually set the IP address of the local network card connected to the computer.
- In AP mode, you can set 2.4G / 5.8G wireless SSID name and password. After setting, setThe prepared WAN port is connected to the external network; other mobile devices connect the SSID name of the device through wireless, enterConnect to the Internet with a password.
- Routing mode settings: Enter the software management page, only display the routing mode, click Routing mode, which can select “PPPoE”, “Static IP”, “Dynamic IP” Three ways to get on line.
- PPPOE dial-up mode: This mode requires the Internet account provided by the network service provider to be filled in Number and password, below can set 2.4G / 5.8G wireless SSID name, wireless password.
- Static IP mode: This mode needs to fill in the IP address provided by the network service provider.Subnet mask, gateway, main DNS address, 2.4G / 5.BG wireless SSID can be set belowName, wireless password.
- Dynamic IP mode: In this mode, the WAN port is assigned IP by the superior network device to access the Internet.The 2.4G / 5.BG wireless SSID name can be set below.
FAQ
Q: What's the role of WiFi extender?
A: Boosts the range of your existing WiFi and creates stronger signal in hard- to-reach areas. Please note that it can't increase the wifi speed of your router, the speed of the extending wifi will lbe reduced.
Q: Where shall I place the WiFi extender?
A: We would suggest that after setting up successfully, please move this wifi extender on the halfway between your router and your weak signal area. The location that you choose must be within the range of your existing WiFi router network.
Q: How to reset the WiFi extender?
A: Press the WPS/Reset button of your extender for 10 seconds, wait to restore factory settings, when the lamp will go out and then light up again, you can begin to set up it again.
Q: Why does WiFi keep disconnecting?
A: We recommend resetting the WiFi extender.
For more questions, please visit www.szcomfast.com official website.
Maintenance Regulations
Dear Valued Clients,
Thank you for purchasing COMFAST products and service to protect your rights, please read the following maintenance regulations.
The following does not belong to free maintenance, our company can provide paid service, please note:
- Failure to require the installation manual, use, maintenance, storage lead to product failure or damage;
- Beyond the limited warranty, the warranty period; Unautorized alteration, tearing up the product bar code;
- Without authorization to change the settings file or inherent disassemble without authorization;
- Unexpected factors or human actions lead to product damage, such as improper input voltage, temperature, water mechanical damage, break, rust or serious oxidation of product,etc;
- Other non-product itself, design ,technology, manufacturing, quality and other quality problems caused by the failure damage.
Statement
Shenzhen Four Seas Global Link Network
Technology CO.,Ltd.Company all rights reserved.
Without ours official writ permission, no unit or individual shall be copied, reproduced, transcribed or translated in part or whole book. In any form or by any means( electronic,mechanical, printing, recording or other possible means)or for the propagation of goods any commercial, profitable purposes.
COMFAST is the registered trademark of Shenzhen Four Seas Global Link Network
Technology Co.,Ltd.Company. All other trademarks or registered trademarks
mentioned in this document, by respective owners.
Product specifications and information mentioned in this manual are for
reference on subject to updates without notice. Unless there are other special
agreed, this manual is used only as a user guide. All statements, information,
etc. are not constitute any form of guarantee.
- Manufacturer: Shenzhen Four Seas Global Link Network Technology Co.,Ltd.Company
- Address: Room 607-61 0,Block B Tao JINDI Electronic Business Incubation Base, Tenglong Road, Longhua District, Shenzhen, China
- Hotline: 4009-001-766
- Website: en.comfast.com.cn
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>