DOMETIC 8516-2M LP Clip On Regulator User Manual
- September 3, 2024
- Dometic
Table of Contents
8516-2M LP Clip On Regulator
“`html
Product Information
Specifications
Product: LP Clip-On Regulator with 2m Hose
Product Code: 8516-2M, 8517-2M
Gas Type: Butane (A121is), Propane (A127is)
Inlet Pressure (bar): Butane: 0.3 – 7.5,
Propane: 1 – 16
Nominal Outlet Pressure (mbar): Butane: 28 –
30, Propane: 37
Working Temperature: Not specified
Capacity: 1.5kg/h
Inlet Connection: G.53-21mm (Butane), G.59-27mm
(Propane)
Outlet Connection: H.50 63mm
Regulator: Yes
Contact Information
- CADAC EUROPE: Ratio 26, 6921 RW Duiven, The
Netherlands | Tel: +31 26 319 7740 | Email: info@cadaceurope.com |
Website: www.cadacinternational.com
Product Usage Instructions
Safety Information
-
The regulator must not be positioned lower than the top of the
tank or outlet valve to prevent gas vapor from draining into the
regulator. -
Ensure any additional pipes or hoses used are inclined so that
liquefied or condensed gas can drain back into the tank.
Installation
Make sure the gas cylinder is turned off before dismounting
it.
Leak Test Procedure
Perform a leak test before using the regulator. Refer to the
user manual for detailed instructions on conducting a leak
test.
Excess Flow Valve Feature (EFV)
The regulator is equipped with an Excess Flow Valve for added
safety. Ensure it is functioning properly before each use.
Frequently Asked Questions (FAQ)
Q: Can I use this regulator with both butane and propane
gas?
A: Yes, this regulator is suitable for use with both butane and
propane gas types. Make sure to check the specific inlet pressure
and connection requirements for each gas type.
“`
LP CLIP-ON REGULATOR WITH 2M HOSE
PRODUCT CODE: 8516-2M, 8517-2M
USER INSTRUCTIONS
EN
NOTE! PRODUCT MAY VARY FROM ILLUSTRATIONS.
503-0934 LEV1
EN
Single-Stage, Low Pressure LP Gas Regulator Type A121is, A127is 2531CS-0140
OPERATING INSTRUCTIONS TO BE KEPT BY THE USER
Read carefully before use
Safety Information
· Always install the regulator in Gas OFF position only. · In normal
conditions of use, in order to ensure a safe operation of installation, it is
recommended that the regulator should be
changed every 5 years from the date of manufacture. · For outdoor use, the
device should be positioned and protected against direct contact of water. ·
Before installation make sure that the rubber seal/gasket in the cylinder
valve or regulator is in good condition. · Make sure all valves on the
appliance are turned off. · Cylinder to be kept in an upright position during
use. · PVC hoses must be in a good condition, with no signs of wear or damage,
and should not be more than 5 years old. · Do not try to remove the regulator
while the gas is ON. · Do not move the cylinder while in operation. · Do not
change the cylinder in the presence of any sources of ignition such as naked
flames · When the regulator is installed downstream of another regulator, the
supply pressure range shall be correct for the regulated
pressure range of the upstream regulator,plus any pressure losses in the
interconnecting pipe work. · That downstream installation pressure loss shall
not exceed the P marked on the device. · If fitting the regulator indirectly
to a pressurized tank:
– The regulator must not be positioned lower than top of the tank or outlet
valve. – This is to avoid any gas vapor which may have re-liquefied from
draining down into the regulator. – Any additional pipes or hoses used to
connect the regulator must be inclined so that any liquefied or condensed gas
can drain back into tank.
Installation
Before installing: · Check the gasket/seal on the cylinder valve is in place
and in good condition. · If the gas valve is not in good condition, ask your
dealer to replace it with another cylinder valve. · Conduct a visual
inspection of the regulator. Remove any dirt or loose metal shavings. · Fit
the gas hose to the gas appliance. Use water or liquid soap for lubrication of
the hose. Insert the hose firmly onto the valve
tailpiece and clamp it securely using the hose clamp provided. · In total
absence of any flame, remove the protection seal or cap from the gas cylinder
valve and attach the regulator to the gas
cylinder. · Press the push button horizontally, mount the regulator onto the
cylinder valve and press the regulator firmly down into place
before releasing the push button. · After ensuring that the regulator is
connected firmly on to the cylinder, turn on the gas supply by turning the
lever, · Perform a leak test as detailed in section 3 below. If no leaks are
indicated, the gas appliance can be started up. · Once you have finished using
the gas appliance, ensure that the gas supply control on both the gas
appliance and the gas
cylinder are turned to the OFF position before dismounting the gas cylinder.
Leak Test Procedure
· It is important that all gas connections have been correctly connected to
prevent any gas leaks. · The correct way to conduct a gas leak test is to
smear all joints along the connection i.e. between the hose and appliance as
well as between the regulator and the gas cylinder, with soapy water. Turn the
appliance control knob slightly anti-clockwise to turn the gas on. If bubbles
form at any of the joints, then there is a gas leak. Immediately turn the gas
off and disconnect the gas supply from the appliance. · Check that all
gaskets/seasl are in place and in good condition before reconnecting the gas
supply. · Ensure that all the connections are properly fitted. · Re-check with
soapy water after refitting the gas supply. · If a gas leak persists, return
the product to your local dealer for inspection/repair.
Excess Flow Valve Feature (EFV)
· The regulator is equipped with a manual excess flow valve, a safety feature
that automatically cuts off gas flow in the event that the hose is
compromised. The excess flow valve is activated during the use of the gas
appliance: – If the gas appliance consumes more gas than 110% of the
regulators rated capacity. – If the gas hose is disconnected. – If the hose
burns through as a result of fire, or if the hose is cut through by accident.
EN
Product Code
Technical Data 8517-2M
8516-2M
Gas Type Model No: Inlet Pressure (bar): Nominal Outlet Pressure (mbar): P 2 (mbar): P 5 (mbar): Working temperature: Capacity: Inlet connection:
Butane A121is 0.3 – 7.5 28 -30
Propane A127is 1 – 16
37
2
2
–
–
0-50 °C
-20-50 °C
1.5kg/h
G.53-21mm
G.59-27mm
Outlet connection: Regulator: Excess Flow:
H.50 63mm
yes
CADAC EUROPE Ratio 26, 6921 RW Duiven The Netherlands Tel: +31 26 319 7740 Email: info@cadaceurope.com www.cadacinternational.com
CADAC GERMANY Ratio 26, 6921 RW Duiven The Netherlands Tel: +31 26 319 7740 Email: info@cadaceurope.com www.cadacinternational.com
CADAC FRANCE Le Viallon, 42520 Veranne France Tel: +33 4 74 78 13 65 Email : info@cadaceurope.com www.cadacinternational.com
CADAC UK 14 Deanfield Court, Link59 Business Park, Clitheroe, Lancashire, BB7 1QS United Kingdom. Tel: +44 (0) 333 2000363 E:mail: info@cadacuk.com www.cadacinternational.com
CADAC SCANDINAVIA Millarco International A/S Rokhøj 26 8520 Lystrup, Denmark Phone: +45 87 43 42 00 millarco@millarco.dk www.millarco.com
CADAC Czech Rep. RÖSLER Praha spol. s r.o. K Horkám 19/21 102 00 Praha 10 Ceská republika Tel: +420 267 188 011 Email: info@rosler.cz www.rosler.cz
CADAC | DOMETIC SOUTH AFRICA Front Runner Outfitter RSA C/o Forssman Close &
River Rd, Barbecue Downs, Kyalami, Johannesburg +27 11 466 0155
www.frontrunneroutfitters.com/en/za/
CADAC NEW ZEALAND Riverlea Group (Pty) Ltd 2A Maui Street, Pukete, Hamilton
3200, New Zealand Tel: +64 7 847 0204 Email: sales@riverleagroup.co.nz
www.riverleagroup.co.nz
CADAC FINLAND OY KAMA FRITID AB Koivuhaantie 2-4 B 01510 VANTAA 00358 20 792
0310 info@kamafritid.fi
CADAC IRAN Robin Bazarganan Carin Co. Unit D, 6th Floor, Negin Zafar Building,
No.1327, Shariati Street, Tehran, Iran Tel: +98 21 276 00 781 Mail:
info@cadac.ir
CADAC U.A.E. Supreme Impex General Trading LLC Office No. 1801-7 Latifa Tower Sheikh Zayed Road Dubai, UAE
CADAC POLAND Kamai Wola Batorska 461 32-007 Wola Batorska Poland Tel: +48 12 635 1373 Email: handlowy@kamai.pl www.kamai.pl
CADAC DENMARK Camper Fritid Industrivej 11 6640 Lunderskov, Denmark Tel.: +45 7558 5255 Email: info@camper.dk www.camper.dk
CADAC SOUTH EAST EUROPE Bulevar oslobodjenja 285 Tel: +381 11 339 2700 Email: sinisaj@cadac.rs www.cadac.rs
CADAC MONTENEGRO City kvart Z1L6 81000 Podgorica, Montenegro Tel 38220671446,
38269020063 E-mail: coca@t-com.me
CADAC ITALY Brunner SRL/GMBH via Buozzi, 8 39100 Bolzano (Italy) Tel: +39 0471
542900 Email: info@brunner.it www.brunnerinternational.com
CADAC CHINA Room 807, Huayue International Building, No.255 Tiangao Road, South Yinzhou business district, Ningbo, China Tel:+86 574 87723937 Email: info@cadac.com.cn
CADAC SWEDEN & NORWAY KAMA FRITID AB 0046 36 353700 info@kamafritid.se
References
- CADAC Dometic Barbecues | Official Website
- CAMPER.DK - Alt i campingudstyr, reservedele og tilbehør til camping
- frontrunneroutfitters.com/en/za/
- Kamai.pl - partner w sprzedaży B2B
- Millarco
- Garden sheds New Zealand Tool shed outdoor fireplaces NZ Hamilton
- Rösler Prague - Consultancy for your projects
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>