COMFAST CF-943AX Wireless Adapter Installation Guide

COMFAST CF-943AX Wireless Adapter

Product Specifications

• Driver Installation Version: V 1.0
• Network Card Type: WiFi6
• Bluetooth: Supported
• Frequency: 5.8GHz

Hardware Installation

There are two ways to install the network card:

1. Insert the network card directly into the USB port of the computer.
2. Connect the computer USB port through the USB extension cord base (USB extension base needs to be purchased separately).

Driver Installation

1. Go to My Computer, find the WiFi6 setup driver disk, open the driver disk and double click Install COMFAST WiFi6.exe.
2. Follow the on-screen instructions to complete the installation.
3. After installation, restart the computer if prompted.
4. Check driver status in Device Manager under Network Adapter.

Hardware installation

There are two ways to install the network card
Note: The picture is a simplified schematic diagram, please refer to the actual product for details.

1. Insert the network card directly into the USB port of the computer；
2. Connect the computer USB port through the USB extension cord base (USB extension base needs to be purchased separately)

Note: When using a desktop computer, it is recommended to use a USB extension cord base to connect to the port on the back of the computer case (some desktop ports have insufficient power supply or cannot be used), and extend it to the Desktop computer usb ports.

Driver Installation

1. Go to My Computer, find the WiFi6 setup driver disk, open the driver disk and double click Install COMFAST WiFi6.exe;
   

2. Open and keep clicking Next to install until the driver installation is complete;

3. After the installation is completed, it will ask whether to restart the computer, if there is a work in progress or file being written, you can choose to restart later, if there is nothing else, it is recommended to choose to restart immediately. If there is nothing else, it is recommended that you choose to reboot immediately;

4.  After restarting, the driver installation is complete, you can move the mouse to My Computer, right-click and select Manage to enter the management interface to view the driver status;

5. After entering the management page, click Device Manager, Network Adapter in turn, you can see the installed network card driver (Note: This step requires the network card to be connected to the computer to see it.);

6.  Double-click to view the device details, if there is no abnormality, the following figure shows that the driver is running normally and can view the driver details and you can view the driver details;

Network connection settings

1. After confirming that the driver is installed correctly, you can double-click the wireless network card icon in the lower right corner, and click the icon with the left mouse button. The computer will display the connectable wireless;
2. Click the wireless network you want to connect to and enter the password to connect
   

 Network connection status

1. After the network is connected, the icon of the computer system will become highlighted , and then you can right-click the icon and select “Open” Network and Internet “settings” to enter the setting selection interface;=
2. Click the “Wi-Fi” option, and then click Show connected wireless, you can view the current IP, MAC address, gateway, driver version, etc. of the wireless.

Bluetooth connection

1. After confirming that the driver is installed correctly, you can double-click the Bluetooth icon in the lower right corner The Add Bluetooth Settings screen is displayed.
2.  Click Add Device in the Settings screen, go to select device type, search for device, and click Device Connection;

Maintenance Regulations

Dear Valued Clients,
Thank you for purchasing COMFAST products. To protect your rights and interests in after-sales service, please read the following maintenance regulations.
The following do not belong to free maintenance, our company can provide paid service, please note:

• Failure to require the installation manual, use , maintenance, and storage led to product failure or damage;
• Beyond the limited warranty, the warranty period; Unauthorized alterations, tearing up the product bar code;
• Without authorization to change the settings file or inherent disassemble;
• Unexpected factors or human actions lead to product damage, such as improper input voltage, temperature, water mechanical damage, break, rust or oxidation product of serious, etc;
• The damage caused by the transportation, loading and unloading caused by the customer’s return for repair; the product failure or damage caused by force majeure such as earthquake, fire, lightning, etc.; Other non-product itself, design, technology, manufacturing, quality and other quality problems caused by the failure damage.

Copyright Information

Statement Shenzhen
Four Seas Global Link Network Technology CO., Ltd. Company all rights reserved.
Without ours official writ permission, no unit or individual shall be copied, reproduced, transcribed or translated in part or whole book. In any form or by any means(electronic, mechanical, printing, recording or other possible means or for the propagation of goods any commercial, profitable purposes.

COMFAST is the registered trademark of Shenzhen Four Seas Global Link Network Technology Co.,Ltd. Company.
All other trademarks or registered trademarks mentioned in this document, by respective owners. Product specifications and information mentioned in this manual are for reference on subject to updates without notice. Unless there are other special agreed, this manual is used only as a user guide. All statements, information, etc. are not constitute any form of guarantee

• Manufacturer: Shenzhen Four Seas Global Link Network
• Technology Co.,Ltd.Company Address: Room 607-610
• Block B Tao JINDI Electronic
• Business Incubation Base,
• Tenglong Road, Longhua
• District, Shenzhen, China
• Hotline: +86 755 83790059 Website: www.comfast.cn / www.szcomfast.com

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.

Specific Absorption Rate (SAR) information:
This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: This device has also been tested against this SAR limit.

This device was tested for typical body-worn operations with the back of the This device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of This device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.

References

• COMFAST
• COMFAST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>