PAX D195 Mobile Payment Terminal User Guide

PAX D195 Mobile Payment Terminal

Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual.ect.,please contact the dealer.

1

AC Power Adapter|

1

USB Cable|

1

Battery|

1

Product Manual|

1

Installation

SAM/SIM card:

1. Remove the battery cover.
2. Remove the battery.
3. Insert the SAM/SIM card to the corresponding card slot (PS: The default hardware configuration only support SIM 1 slot).

Battery:

Alignment battery tip side to battery tip in terminal and insert.

Instruction

Power ON/OFF

Power on: Plug in power adapter or insert the battery, Press button for 3 seconds until the PAX LOGO display on LCD.
Power off: Press button for 3 seconds until the “Power off” display on the LCD ,then press “ENTER”, then the POS terminal is being turned off.

IC Card

Put IC card chip side upward. push-in IC card slot and to bottom.

Contactless Card

The card read area is above the LCD, Put the card above the LCD.

Battery Charge display

Connecting USB port with external adapter can charge the battery. And there are charging display.

Battery Charge style

Please use the original adapter, if you need to charge.
Working Environment:
Temperature : 0°C~45°C(32°F~113°F)
Humidity : 10%~93%( non-condense) Storage Environment:
Temperature :-20°(~ 70°(c-4 °F~158°F)
Humidity. :5%~95% (non-condense)

Installation and Usage Tips

1. Avoid putting the terminal in direct sunlight. high temperature, moist. or dusty environment.
2. Forbid non-professional to repair the terminal.
3. Before insert the card, please check internal and around of IC card slot. if you found some suspicious objects , must report to related administrator.

Lithium Ion Battery Usage Tips

WARNING:

1. Don’t use the battery in sunlight or smoke. dust environment.

2. Prohibited to strike. squeeze and tread on battery or throw it into the liquid and fire.

3. If battery is impressive. deformed. damaged or exothermic seriously. please stop using immediately and replace it!

4. If the continuous working time is only half of new one.
   the battery life may be end. Please replace it!

5. Must use the specified battery model and charger. otherwise there will be explosion.

6. Charging time can not exceed 24 hours. If the battery is out of power. please recharge in time. Avoid damaging the battery in over-charge and over-discharge.

7. If be non-use for long time. please recharge the battery per 6 months to avoid shortening its life.

8. Suggest to replace it when the battery have been used for 2 years.

9. Be sure to follow the instructions to dispose the wasted batteries.

Icon shows

Do not throw away, need professional recycling.
Class II Equipment
For indoor use only
Energy Efficiency Marking
AC voltage
DC voltage

The full text of the EU declaration of conformity is available at the following internet address:
https://www.pax.eom.cn/product/ce/list/
P/N: 200312000000866

PAX continually invests to maintain its high quality products up to date with the latest certifications. therefore a comprehensive list can be requested via the website’s contact form or on downloadable product brochures.

FCC Regulations

This device has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Exposure Information (SAR)

The SAR limit of FCC is l.6W/kg averaged over one gram of tissue. For body- worn operation, this device has been tested and meets the FCC exposure guidelines. when used with an accessory, the accessory should not contain any metal element and positioned minimum of 5 mm from the body. RF exposure compliance with any accessory that contains metal was not tested and certified, and use of such accessory should be avoided.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The device is going on be operated in 5150~5250 frequency range. It is restricted indoor environment only in Canada.

RF Exposure Information (SAR)

This equipment complies with RSS 102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

FCC Supplier1s Declaration of Conformity

Smart Mobile Payment Terminal / D195 This device complies with part 15 of the FCC Rues. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC ID and IC ID can be found by opening the battery cover.
Responsible Party: PAX Technology, Inc 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville , Florida, 32256 Help-desk 1 877-859-0099

Customer Support

Built by : PAX Computer Technology (Shenzhen) Co. Ltd.
Address: 4/F. No.3 Building. Software Park, Second Central Science-Tech Road. High-Tech Industrial Park Shenzhen. Guangdong. China.
Tel: +86 755 86169630
Website: www.pax.com.cn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>