tp-link tapo S500D Smart Wi-Fi Light Switch Dimmer User Guide

tp-link tapo S500D Smart Wi-Fi Light Switch Dimmer

Specifications

• Product: Smart Wi-Fi Light Switch, Dimmer
• Model: Tapo
• Features: Dimming capability, Wi-Fi connectivity
• Compatibility: Works with Tapo Smart Sensor and Tapo Hub
• Power Requirement: Standard electrical connection
• Control: App-based control using Tapo App

Product Usage Instructions

Wire Your Smart Wi-Fi Dimmer Light Switch

1. Before You Start: Ensure you have the necessary tools and a strong Wi-Fi signal in the installation area.
2. Step 1 – Turn Off Power and Remove Wallplate: Switch off the circuit breaker, remove the old wallplate, and label the wires.
3. Step 2 – Expose Your Switch Wiring: Unscrew the old switch, disconnect wires, and label Line and Load wires.
4. Step 3 – Identify Line and Load wires: Turn on the circuit breaker, use a voltage detector to identify the Line wire.
5. Step 4 – Connect the Wires: Connect the wires to the smart dimmer switch following the provided instructions.
6. Step 5 – Install Your Smart Dimmer: Secure the switch in place with screws and fold the wires back into the wall box.
7. Step 6 – Attach Wallplate and Turn on Power: Attach the wallplate, turn on the circuit breaker to complete the wiring process.

Set Up Your Switch

1. Step 1 – Download Tapo App: Download and install the Tapo App on your smartphone or tablet from the respective app store.

Frequently Asked Questions (FAQ)

• Q: What do the LED status indicators on the Smart Wi-Fi Light Switch signify?
  A: The LED indicators represent different statuses such as starting up, ready for setup, connecting to Wi-Fi, connected to Wi-Fi, disconnected from Wi-Fi, device resetting, firmware upgrading, and more. Refer to the user manual for detailed explanations of each status.

• Q: Can I install the Smart Wi-Fi Dimmer Light Switch myself?
  A: If you are familiar with basic electrical wiring and follow the provided instructions carefully, you can install the switch yourself. However, if you are unsure, it is recommended to consult a qualified electrician for installation.

• Q: How do I reset the Wi-Fi settings on the Smart Wi-Fi Light Switch?
  A: To reset Wi-Fi settings, press and hold the designated button for about 5 seconds while keeping other settings intact. For a factory reset, press and hold the button for about 10 seconds to restore default settings.

User Guide
Smart Wi-Fi Light Switch, Dimmer

About This Guide

This guide provides a brief introduction to the Smart Wi-Fi Light Switch, Dimmer and regulatory information.
Please note that features available in Tapo may vary by model and software version. Tapo availability may also vary by region. All images, steps, and descriptions in this guide are only examples and may not reflect your actual Tapo experience.

Conventions
In this guide, the following convention is used:

menus, items, buttons and so on.
Underline| Hyperlinks are in blue and underlined. You can click to redirect to a website.
Note:| Ignoring this type of note might result in a malfunction or damage to the device.

More Info

• Specifications can be found on the product page at https://www.tapo.com .
• Our Technical Support and troubleshooting information can be found at https://www.tapo.com/support/ .

Introduction

With the Tapo Smart Wi-Fi Dimmer Light Switch, Matter, customize lighting ambience from anywhere.

• Brightness Control – Control the brightness of your lights to set the ideal ambiance for different activities.
• Fade On/Off – Slowly increase brightness or dim to off when turning lights on/off
• Voice Control – Manage your smart switch with voice commands via Amazon Alexa, Apple Siri®, or Google Assistant.
• Remote Control – Instantly turn connected devices on/off from wherever you are through the Tapo app.
• Schedule – Preset a schedule to automatically manage devices.
• Away Mode – Randomly turns devices on and off at different times to give the appearance that someone is home.
• Smarter with Sensors – Create Smart Actions triggered by Tapo smart sensors for greater automation (Tapo Smart Sensor are sold separately. When working with a Tapo Smart Sensor, the Tapo Hub is required).

Appearance

Button Explanations

| Decrease or increase the brightness.
---|---
Reset|

• Press and hold for about 5s to reset Wi-Fi while keeping other settings.
• Press and hold for about 10s to restore your switch to factory default settings.

Restart| Press to restart your switch.

LED Status

Wire Your Switch

Follow the steps below to wire your Smart Wi-Fi Dimmer Light Switch. If you are not familiar with basic electronical wiring, please consult an electrician.

Before You Start

1. Prepare Baisc knowledge of Wiring

2. Ground: Usually green or copper.

3. Neutral: Usually white, not connected to the dumb switch.

4. Line: Usually black and coming from the circuit breaker.

5. Load: Usually black. One end is connected to the light.
   Note: If you are unsure, consult a qualified electrician.

6. Prepare Your Tools
   Prepare a philips and slotted screwdriver, pliers, wire strippers and a voltage detector.

7. Check Wi-Fi Strength
   Make sure your switch is in a area with strong Wi-Fi signal.

Wire Your Switch

1. Step 1. Turn Off Power and Remove the Wallplate
   Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the wires.
   CAUTION
   Risk of Electric Shocks – High Voltage – Disconnect power supply before servicing.
   

2. Step 2. Expose Your Switch Wiring
   Remove the screws securing your old switch to the wall box. Gently pull the switch out and disconnect wires from the old switch.

3. Step 3. Identify Line and Load wires

4. Turn on the circuit breaker. Use a voltage detector to identify the energized wire (Line wire).

5. Turn off the circuit breaker. Label the Line and Load wires.

6. Step 4. Connect the Wires
   Connect the wires to the smart dimmer switch as shown below.

7. Step 5. Install Your Smart Dimmer
   Gently fold all of the wires back into the wall box. Line up the switch with the mounting holes. Secure it with screws.

8. Step 6. Attach the Wallplate and Turn on Power
   Attach the wallplate and turn on the circuit breaker. Then the wiring is finished.

Set Up Your Switch

Follow the steps below to set up your dimmer switch.

1. Step 1. Download Tapo App
   Get the Tapo app from the App Store or Google Play, or by scanning the QR code below.

2. Step 2. Log In
   Open the app, and log in with your TP-Link ID. If you don’t have an account, create one first.

3. Step 3. Add Your Switch
   Tap the + button in the app and select your switch. Then follow app instructions to set up your switch.

Authentication

FCC compliance information statement

• Product Name: Tapo Smart Wi-Fi Light Switch, Dimmer
• Model Number: Tapo S500D
• Responsible party:
  • TP-Link USA Corporation
• Address: 10 Mauchly, Irvine, CA 92618
• Website: http://www.tp-link.com/us/
• Tel: +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

• This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
• “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
• We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

• Note 1： “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence
• condition.
• Note 2 ：“ ○ ” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
• Note 3 ：The “−” indicates that the restricted substance corresponds to the exemption.

Safety Information

Before installing, servicing or removing the switch, read and follow all safety precautions including the following:

• Follow all national and local safety regulations and practices. If you are uncertain or uncomfortable when performing the installation, consult a qualified electrician.
• CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment and luminaire before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
• Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Rating: 120 V~ 60 Hz
• Supported Load: 300 W Incandescent, 150 W LED
• Operation temperature: 0~40 °C
• Tighten terminal screws to 13 lbf-in.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).

Explanation of the symbols on the product label

Symbols may vary from products

Documents / Resources

| tp- link tapo S500D Smart Wi-Fi Light Switch Dimmer [pdf] User Guide
S500D US, tapo S500D Smart Wi-Fi Light Switch Dimmer, tapo S500D, Smart Wi-Fi Light Switch Dimmer, Wi-Fi Light Switch Dimmer, Light Switch Dimmer, Switch Dimmer, Dimmer
---|---

References

• Link: Simple, secure one-click payments
• WiFi Networking Equipment for Home & Business | TP-Link
• Tapo | Smart Devices for Smart Living

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>