peerless-AV DS-LEDUNV1220-3×3 Seamless Kitted Universal Installation Guide

: August 2, 2024
: Peerless-AV

Table of Contents

peerless-AV DS-LEDUNV1220-3×3 Seamless Kitted Universal
Product Usage Instructions
FAQ
Tools
Parts
Installation Instruction
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

peerless-AV DS-LEDUNV1220-3×3 Seamless Kitted Universal

Specifications:

Model: SEAMLESS Kitted Universal Series
Actual configuration may vary
Date: 2024-03-04
Part Number: #146-9082-2 (2024-04-05)

Product Usage Instructions

Tools Needed for Assembly:

5/32 (4mm) Allen wrench
3/8 (10mm) Allen wrench
5mm, 6mm, 8mm socket wrenches

Parts List:

Before beginning assembly, ensure you have all the parts listed below:

A latch assembly
4′ horizontal extrusion
Wall plate
Depth adjustment bracket
Connector plate
Various screws and washers as per the parts list

Wall Mount Dimensions:

Refer to the table below for the dimensions to locate the mounton the wall based on the compatible display model.

Compatible Display| Top of the video wall to center of first wall plate (Dimension
A)| Side of video wall to center of first wall plate (Dimension
B)| Center to center of wall plates (Dimension C)
---|---|---|---

FAQ

Q: How tight should the screws be?
- A: Tighten screws until the screw head makes contact, then tighten another half-turn. Do not over-tighten.
Q: How many turns should the screws get?
- A: Screws must receive at least three full turns and fit snugly.
Q: Why wear anti-static gloves during assembly?
- A: Anti-static gloves help prevent damage to sensitive electronic components during assembly.

WARNING

This product is designed to be installed on plywood walls. Hardware is included for plywood installation. This product is designed to be installed on flat, unobstructed, vertical walls. Do not install on curved or angled walls. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be careful not to pinch fingers when operating the mount. For support please call customer care at 1-800-865-2112.

Symbols

To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws.

Tools

Tools Needed for Assembly

Parts (Before beginning, make sure you have all parts shown below). *Refer to parts list included with your model.

Parts

Parts List

Parts List

| Description| Qty.
N| spacer| 2
O| 3mm allen wrench| 1
P| wall plate shim| 10
Q| 4mm allen wrench| 1
R| spacer extension| 2
S| M5 flat-head screw| 8
T| 1/4″ flat washer| 8

Installation Instruction

See the table and drawing below for the dimensions that will locate the mount on the wall.

Compa�ble Display

| Bo�om of the video wall to the

top of the ﬁrst wall plate.

Dimension A

| Side of video wall to

center of first wall plate Dimension B

| Center to center

wall plates. Dimension C

| System Depth Range.

Dimension D

---|---|---|---|---
Absen Acclaim Plus/Pro/V3| 345.24| 305| 610| 120.65-137.67
Absen KL II| 395.74| 320| 640| 136.40-153.67
Absen NX| 582.74| 240| 480| 115.06-132.08
AOTO CVE| 360.25| 300| 600| 108.71-125.98
Barco XT| 382.17| 305| 610| 142.75-159.76
Christie CSII| 368.24| 300| 600| 108.71-125.98
Christie CSIII| 368.24| 300| 600| 100.58-117.86
Fabulux T Series| 515.24| 250| 500| 103.88-121.16
INFiLED WP| 365.49| 300| 600| 101.34-118.36
INFiLED WT| 365.49| 300| 600| 101.34-118.36
Jupiter ZavusXP0.7| 290.73| 240| 480| 99.57-116.58
Jupiter ZavusXP0.9-1.2| 348.23| 300| 600| 99.57-116.58
Just Video Walls| 361.9| 300| 600| 110.74-127.76
Leyard GF| 504.74| 320| 640| 145.54-162.56
LG LSAC| 700.68| 300| 600| 122.68-139.70
LG LSBB| 384.45| 300| 600| 127.25-144.27
LG LSBE| 380.37| 300| 600| 143.51-160.53
LG LSBF| 715.72| 300| 600| 143.51-160.53
LG LSCA-GK2 (500×500)| 532.79| 250| 500| 136.65-153.67
LG LSCA-GK (500×1000)| 1032.79| 250| 500| 136.65-153.67
LG LSCB| 365.49| 300| 600| 101.09-118.11
Linsn MA640| 505.74| 320| 640| 128.52-145.79
Linsn N169S| 382.74| 300| 600| 117.60-134.87
MAXHUB M27| 378.87| 320| 640| 102.61-119.63
Philips 27BDL6000| 382.74| 304| 608| 130.55-147.57
Philips 28HDL5000| 538.69| 250| 500| 113.54-130.81
Philips 44HDL5000| 1038.69| 250| 500| 113.54-130.81
Planar 27″ DLP| 380.94| 302.4| 604.8| 116.58-133.86
Planar 36″ DLP| 721.14| 302.4| 604.8| 116.58-133.86
QST PH| 365.49| 300| 600| 108.20-125.47
Samsung IEC| 373.24| 300| 600| 109.73-127
Sharp NEC E Series| 379.49| 300| 600| 100.58-117.60
Sharp NEC FA, FC, FE| 378.74| 304| 608| 120.65-137.67
SNA VST| 480.74| 200| 400| 117.60-134.62
SNA VTII| 475.74| 200| 400| 144.78-162.05
Sony BC| 377.74| 304| 608| 120.14-137.16
Sony BHCH| 345.24| 305| 610| 140.21-157.22
Unilumin ULWIII| 378.24| 300| 600| 116.33-133.35
Unilumin Umini III| 378.24| 300| 600| 112.01-129.28
Unilumin Upanel II| 383.82| 305| 610| 139.70-156.72
Unilumin UPanelS| 381.53| 305| 610| 142.75-159.77
Unilumin UPanelSII| 383.82| 305| 610| 136.65-153.92
Unilumin Uslim II (500×250)| 290.69| 250| 500| 110.23-127.51
Unilumin Uslim II (500×500)| 499.9| 250| 500| 110.23-127.51
Unilumin Uslim II (500×1000)| 1040.74| 250| 500| 110.23-127.51
Unilumin UTWIII| 580.79| 240| 480| 99.82-116.84

Optional: connecting two horizontal extrusions

Determine the required extrusion length with the following extrusion cut-to- length formula:

Video Wall Width – 0.25″ (6mm) = Extrusion

Now that the extrusions are cut to length, separate the extrusions and slide wall plates onto horizontal extrusions and tighten with the wall plate fully extended (one wall plate per display unless the display is >960mm wide, in which case there will be two wall plates per display).

WARNING

When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2″ x 4″ nominal size and plywood is a minimum Grade BC, 1/2″ (13mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8″ thick

Install the bottom row, first extrusion assembly, on the laser line per table (step 1), dimension “A”. Install additional bottom row extrusions one at a time using connector plates to join extrusions. Drill mounting holes and install screws and washers with top edge of the wall plates on the laser line

Determine the height of the display being mounted and locate the same dimension on the front of the spacer. If the display height is above 540mm, add the spacer extension. If display height is not listed on the spacer, measure the display to set custom spacing

Add the extension for displays taller than 540mm. Move the spacer bracket and clamp to the lower extension

Move spacer bracket and clamp to the desired display height. This may require adjusting the pins of spacer bracket.

Optional: Remove and replace pins to align with correct display height

If the display height is not listed on the spacer, measure the display to set the spacing.

Install remaining extrusions using the spacers. Clamp the upper spacer jaw assembly to an uninstalled extrusion assembly. Clamp the bottom spacer jaw assembly to the installed extrusion. Vertically align extrusions with a laser. Drill mounting holes into supporting surface and install wall plates to the wall

Loosen clamps and remove spacers. Repeat steps above to install the next extrusion.

Engage and secure connecter plate to mounted extrusions. Secure wall plates to wall. Remove spacer when extrusions are fully secured.

Set a laser level so that it is parallel to the mounting surface (wall). Measure to the face of the extrusion so that all points of the extrusion are the same distance from the laser line, creating one flat plane across the face of the mount. Tighten screws Double check using a straight edge to span three extrusions. Adjust low and high spots as needed

Hook display cabinets onto horizontal extrusion, adjust height to level and join cabinets together using connecting system. Adjust plumb, close latch, then run cables one at a time starting from left to right.

Hook display cabinets onto horizontal extrusion, adjust height to level and join cabinets together using connecting system. Close latch, then run cables one at a time starting from left to right
To remove, start from the top right. Open latch assemblies, disconnect cables, separate cabinets and remove displays one at a time

Warranty

Peerless-AV