YeeSite YS-23-144LED RGB Stage Light Bar User Manual
- June 1, 2024
- YeeSite
Table of Contents
YeeSite YS-23-144LED RGB Stage Light Bar
SAFETY INSTRUCTIONS
FOR YOUR OWN SAFETY,PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP!
CAUTION: Keep this equipment away from rain, moisture and liquids.
Every person involved with the installation, operation & maintenance of this equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION : Take care using this equipment! high voltage-risk of electric shock!!
Before your initial start-up, please make sure that there is no damage caused
during transportation.Should there be any, consult your dealer and do not use
the equipment.
To maintain the equipment in good working condition and to ensure
safeoperation, it is necessary for the user to follow the safety instructions
and warning notes written in this manual.
Please note that damages caused by user modifications to this equipment are
not subject to warranty.
Digital Display Operate
a). Illustration part:
- A.MENU
- B.UP
- C.DOWN
- D.ENTER
Operation Instructions
After starting pressA(MENU) Enter into main-menu, Press B(UP) C(DOWr) to select the submenu, and then press D(ENTER) to ensure.
ATTENTION : DANGER OF LIFE!
RISK OF BURNS! RISK OF FIRE! RISK OF SHORT CIRCUIT!
DMX Signal Connection
3 – Pin XLR to 5-Pin XLR Conversion
Conductor| 3- Pin XLR Female (OUT)| 5- Pin XLR Male (IN)
Ground/ Shield| Pin 1| Pin 1
Data Compliment (- signal)| Pin 2| Pin 2
Data True (+signal)| Pin 3| Pin 3
Not Used| | Pin 4- Do Not Used
Not Used| | Pin 5- Do Not Used
Technical Specifications
- Voltage : AC110-240V, 50/60Hz
- Consumption : 60W
- LEDs : 144Pcs (12*12Pcs) SMD 5050 3IN1 RGB LEDs
- Operation :Auto, DMX512,Sound ,Master/Slave
- Channel : 3/5/8/36/40CHs, With LCD display,
- Color : RGB color can be mixed to more than 16. 7 million kinds of color.
- Beam Angle : 90°
- Dimmer : 0-100% linear dimming
- OMX in/out,Power in & Power out.
- Dimension : 1005.59cm
- N.W : 1.75KG; G.W:2.15KG
SETTING MENU LED DISPLAY
| Mode | Programming | Description |
|---|---|---|
| Auto mode | Auto | Sp1-10 |
| St0-9 | (slow->fast) | |
| OMX mode | Addr | 3CH |
plugged into the console , automatically enter OMX mode
5CH| A001-A508
8 CH| A001-A505
36CH| A001-A477
40CH| A001-A473
Show| Shou| Sh 1-56| Program Show 1-56
Sp1-10| Program Speed 1-10 (slow->fast)
St0-9| Program Flash 0-9 (slow->fast)
Sound Mode| Soud| Sou1-2| Sen1-9| Sound active modes 1-2,sound sensitivity 1-9
Slave| SLAV| Slave| Slave (Slave, automatically identify the master)
Edit color| Colo| r000-255| Red (0-100%) Red Dimming
g000-255| Green (0-100%) Green Dimming
b000-255| Blue (0-100%) Blue Dimming
St0-9| LED Strobe (slow->fast)
Static colors| StAt| CL01-CL37| static color (37 static colors to choose from)
St0-9| LED Strobe (slow->fast)
Product Set| Set| dis| 10s| Set display board backlight time,10 seconds to
always on, factory default 10 seconds
20s
30s
60s
on
temP| 50- 65°C| Protection temperature setting,50- 65°C range protection ,more
than this range began to reduce the output power
dir| —>| Chasing direction : right
<—| Chasing direction : left
InFr| on| Remote control function setting on
oFF| Remote control function setting oFF
Send| yes| one button to set the send function to send the current light
channel mode and temperature protection value to other lights connected to
this light.(No other controller on the line)
Send
Information| Info| ver| VVxx| Software version
temp| xxc| The current light board temperature( degrees Celsius), if the
temperature detection line failure , power on prompt -RT-, menu display error
DMX MODE 1:3 CH
| CH1 | 0-255 | ALL RED (0-100%) |
|---|---|---|
| CH2 | 0-255 | ALL GREEN(0-100%) |
| CH3 | 0-255 | ALLBLUE(0-100%) |
DMX MODE 2:5 CH
| CH1 | 0-255 | Master Dimmer |
|---|---|---|
| CH2 | 0-9 | No Function |
| 10-255 | Slow->Fast | |
| CH3 | 0-255 | ALL RED (0-100%) |
| CH4 | 0-255 | ALL GREEN(0-100%) |
| CH5 | 0-255 | ALL BLUE (0-100%) |
DMX MODE 3:8 CH
| CH1 | 0-255 | Master Dimmer |
|---|---|---|
| CH2 | 0-255 | ALL RED (0-100%) |
| CH3 | 0-255 | ALL GREEN(0-100%) |
| CH4 | 0-255 | ALL BLUE(0-100%) |
| CHS | 0-9 | No Function |
| 10-255 | Slow->Fast | |
| CH6 | 0-3 | CH2-4 Control the overall flower color |
| 4-7 | Pattern Effect 1(CH2-4 Control the pattern color) | |
| 8-11 | Pattern Effect 2(CH2-4 Control the pattern color) | |
| 148-151 | Pattern Effect 37(CH2-4 Control the pattern color) | |
| 152-155 | Pattern Effect 38(Built-in effect colors) | |
| 156-159 | Pattern Effect 39(Built-in effect colors) | |
| 224-227 | Pattern Effect 56(Built-in effect colors) | |
| 228-231 | Auto Effect (Cyclic running pattern effect 1-56) | |
| 232-235 | Sound 1 | |
| 236-255 | Sound 2 | |
| CH? | 0-255 | RGB Program Speed(Slow->fast) |
| CH8 | 0-255 | CH6 in the pattern 1 – pattern 25, this channel is used as a |
pattern background color selection function (see final background color table for details)
DMX MODE 4:36 CH
| CH1 | 0-255 | R1(0-100%) |
|---|---|---|
| CH2 | 0-255 | G1(0-100%) |
| CH3 | 0-255 | B1(0-100%) |
| CH34 | 0-255 | R12(0-100%) |
| CH35 | 0-255 | G12(0-100%) |
| CH36 | 0-255 | B12(0-100%) |
DMX MODE 5:40 CH
| CH1 | 0-255 | R1(0-100%) |
|---|---|---|
| CH2 | 0-255 | G1(0-100%) |
| CH3 | 0-255 | B1(0-100%) |
| CH34 | 0-255 | R12(0-100%) |
| CH35 | 0-255 | 812(0-100%) |
| CH36 | 0-255 | B12(0-100%) |
| CH37 | 0-9 | No Function |
| 10-255 | Slow->Fast | |
| CH38 | 0-3 | CH1-37 Control single segment |
| 4-7 | Pattern Effect 1(CH1-3 Control the pattern color) | |
| 8-11 | Pattern Effect 2(CH1-3 Control the pattern color) | |
| 148-151 | Pattern Effect 37(CH1-3 Control the pattern color) | |
| 152-155 | Pattern Effect 38(Built-in effect colors) | |
| 156-159 | Pattern Effect 39(Built-in effect colors) | |
| 224-227 | Pattern Effect 56(Built -in effect colors) | |
| 228-231 | Auto Effect(Cyclic running pattern effect 1-56) | |
| 232-235 | Sound 1 | |
| 236-255 | Sound 2 | |
| CH39 | 0-255 | RGB Program Speed(Slow->fast) |
| CH40 | 0-255 | Ch38 in pattern 1 – pattern 25, this channel is used as a pattern |
background color selection function (see final background color table for details)
RGB 3 in 1 Background Color Table
| Value | Color |
|---|---|
| 0-6 | R:000 G:000 B:000 |
| 7-13 | R: 51 G:000B :000 |
| 14-20 | R:102 G:000 B:000 |
| 21-27 | R:153G:000B:000 |
| 28-34 | R:204G :000 B:000 |
| 35-43 | R:255G:000 B:000 |
| 42-48 | R:000G: 51 B:000 |
| 49-55 | R:000G:102 B:000 |
| 56-62 | R:000 G:153 B:000 |
| 63-69 | R:000 G:204 B:000 |
| 70-76 | R:000 G:255 B:000 |
| 77-83 | R:000 G:000 B: 51 |
| 84-90 | R:000G:000B:102 |
| 91-97 | R:000 G:000 B:153 |
| 98-104 | R:000 G:000 B:204 |
| 105-111 | R:000 G:000 B:255 |
| 112-118 | R: 51 G: 51 B:000 |
| 119-125 | R:102 G:102 B:000 |
| 126-132 | R:153 G:153 B:000 |
| 133-139 | R:204 G:204 B:000 |
| 140-146 | R:255 G:255 B:000 |
| 147-153 | R: 51 G:000 B: 51 |
| 154-160 | R:102 G:000 B:102 |
| 161-167 | R:153 G:000 B:153 |
| 168-174 | R:204 G:000 B:204 |
| 175-181 | R:255 G:000B :255 |
| 182-188 | R:000 G: 51 B: 51 |
| 189-195 | R:000 G:102 B:102 |
| 196 -202 | R:000 G:153 B:153 |
| 203-209 | R:000 G:204 B:204 |
| 210-216 | R:000 G:255 B:255 |
| 217-223 | R: 51 G: 51 B: 51 |
| 224-230 | R:102 G:102 B:102 |
| 231-237 | R:153 G:153 B:153 |
| 238-244 | R:204 G:204 B:204 |
| 245-255 | R:255 G:255 B:255 |
MAINTENANCE
Dust build-up reduces light output performance and can cause overheating. This
can lead to reduction of the light source’s life andlor mechanical wear. To
maintain optimum performance and minimize wear, clean your lighting.
products at least twice a month.However, be aware that usage and environmental
conditions could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
- Unplug the product from power.
- Wait until the product is at room temperature.
- Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
- Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
- Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
- Softly drag any dirt or grime to the outside of the transparent surface.
- Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
CAUTION : Take care using this equipment! high voltage-risk of electric shock!!
Customer Support
At first,thank you for purchasing the device.For the sake of safety and
regular operation of this projector,please read this manual carefully before
using and operating it in order to avoid any personal injury or damage to the
device.
info@oppsk.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>