PARKSIDE IAN 446806 3-in-1 Sun Protection Window Instruction Manual
- July 31, 2024
- PARKSIDE
Table of Contents
IAN 446806 3-in-1 Sun Protection Window
Instruction Manual
IAN 446806 3-in-1 Sun Protection Window
3-IN-1 SUN PROTECTION WINDOW FILM/ UV PROTECTION WINDOW FILM
Assembly and safety instructions
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY! List of pictograms
used
Safety information
Instructions for use 3-in-1 Sun Protection Window Film/ UV Protection Window
Film
Introduction
We congratulate you on the purchase of your new product. You have chosen a
high quality product. Familiarise yourself with the product before using it
for the first time. In addition, please carefully refer to the operating
instructions and the safety advice below.
Only use the product as instructed and only for the indicated field of
application.
Keep these instructions in a safe place. If you pass the product on to anyone
else, please ensure that you also pass on all the documentation with it.
Intended use
This product is only intended for private household use, not for commercial
use.
Scope of delivery
- 1 adhesive film (approx. 75 x 220 cm)
- 1 cutter
- 1 squeegee
- 1 assembly instruction
Safety information
PLEASE KEEP ALL SAFETY INSTRUCTIONS AND INSTRUCTIONS FOR USE FOR FUTURE
REFERENCE!
Note: Glass breakage is not covered by the warranty!
The warranty and all warranty claims are restricted to the replacement of the
product and do not extend to glass breakage. The warranty and all warranty
claims become null and void when the product is used in any of the cases named
under “Safety information”.
Warning: Risk of injuries – sharp blade. Wear protective gloves and
goggles.
Keep out of the reach of children.
CAUTION! This product may not be used in motor vehicles! The product is
not approved under the road traffic registration regulations! The product may
be attached to the inside of the glazing only! The product may not be attached
to heated glazing (e.g. glazing exposed to direct sunlight).
The product may not be used on the following base surfaces
- circular, rounded, curved, coated, ribbed, or wired glazing or skylights
- partially tinted glazing (outside tint of 20% or more per pane)
- triple or quadruple insulation glazing
- panes exceeding a side length of three metres
- damaged or scratched glazing
- stained glass or glazing with adhesive lettering or vinyl motifs
- glass framed in concrete
- broken panes or insulating glazing with damaged gaskets
ATTENTION! Risk of heat-induced breakage!
In general, there is a very small risk of heat-induced breakage on glass and
glazing, but it cannot be ruledout completely. If this risk is to be minimised
the productmust be attached in accordance with the operating instructions and
the following information: – The edges of the pane must be smooth.
– The risk of breakage grows with the size of the pane.
Radiators and air conditioners
Please bear in mind that heat and cold sources can cause abrupt temperature
fluctuations at local areas of glazing and so aggravate any thermal loads on
the materials.
ATTENTION! Prevent the build-up of heat by installing additional internal
shade systems.
The most common forms of internal shading are e.g. Venetian blinds, net
curtains, roller shutters, screens, partitions attached to the inside of the
glazing (over part or all of the glazed facade), stained glass, adhesive
lettering, transfers, etc. Please avoid shading on the glaz ing cast by
structural or natural elements because these can give rise to local
temperature drops.
The most common forms of external shading are roof overhangs, neighbouring
buildings, brise-soleils, external roller shutters, external Venetian blinds,
pillars, columns, and natural elements (e.g. trees). The building’s altitude
and the alignment of the glazing affect the thermal load. For example, glazing
facing the south or sky can be subject to the greatest thermal load in the
northern hemisphere.
Assembly
- Before the product is attached the glazing must be examined for its suitability as a base surface for thermal insulation foils.
Inside mounting
Assemble the product as shown in the figures.
Required work tools:
- cutter (included in scope of delivery)
- squeegee (included in scope of delivery)
- adhesive tape to remove the protective layer
- spray bottle with a solution of water and washing-up liquid (about one litre of distilled water and eight drops of washing-up liquid)
- ruler
- Clean thoroughly the inside and outside of the glass surfaces taking the foil (see Fig. 1).
- Measure the size of the glass surface and carefully trim the foil (see Fig. 2). Make sure the trimmed foil fits.
- Spray the glass surface copiously with the solution of water and washing-up liquid (see Fig. 3). The glass surface may not dry when the foil is being attached.
- Attach an adhesive strip to both the front and back of the foil. You can then draw the base foil easily and cleanly off the tinting foil (see Fig. 4).
- Now moisten the adhesive film on the tinting foil with the solution of water and washing-up liquid (see Fig. 5).
- Place this wet adhesive side of the foil on the wet inside of the glass surface and push the foil into position (see Fig. 6).
- Using the squeegee squeeze the liquid in a horizontal direction from under the foil until there are no more air bubbles between the foil and the glass surface (see Fig. 7).
Removing the product
Detach the product from the glass surface at one corner, and carefully draw
off the foil. Any adhesive residue can be removed with a standard glue
remover.
Cleaning and care
- Do not use aggressive cleaning or abrasive agents!
- Once the adhesive film has dried (about forty-eight hours after the foil has been attached) the foiled surfaces can be cleaned with a glass cleaner and a soft cloth.
Disposal
The packaging is made entirely of recyclable materials, which you may dispose
of at local recycling facilities.
Contact your local refuse disposal authority for more details of how to
dispose of your worn-out product.
Warranty
The product has been manufactured to strict quality guidelines and
meticulously examined before delivery.
In the event of material or manufacturing defects you have legal rights
against the retailer of this product.
Your legal rights are not limited in any way by our warranty detailed below.
The warranty for this product is 3 years from the date of purchase. The
warranty period begins on the date of purchase. Keep the original sales
receipt in a safe location as this document is required as proof of purchase.
Any damage or defects already present at the time of purchase must be reported
without delay after unpacking the product.
Should the product show any fault in materials or manufacture within 3 years
from the date of purchase, we will repair or replace it – at our choice – free
of charge to you. The warranty period is not extended as a result of a claim
being granted. This also applies to replaced and repaired parts.
This warranty becomes void if the product has been damaged, or used or
maintained improperly.
The warranty covers material or manufacturing defects.
This warranty does not cover product parts subject to normal wear and tear,
thus considered consumables (e.g. batteries, rechargeable batteries, tubes,
cartridges), nor damage to fragile parts, e.g. switches or glass parts.
Warranty claim procedure
To ensure quick processing of your case, please observe the following
instructions:
Please have the till receipt and the item number (IAN 446806_2307) available
as proof of purchase.
You will find the item number on the rating plate, an engraving on the front
page of the instructions for use (bottom left), or as a sticker on the rear or
bottom of the product.
If functional or other defects occur, please contact the service department
listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address
that will be provided to you. Ensure that you enclose the proof of purchase
(till receipt) and information about what the defect is and when it occurred.
Service
Service Great Britain
Tel.: 08000569216
E-Mail: owim@lidl.co.ukhttp://www.lidl-service.com
OWIM GmbH & Co. KG
Stiftsbergstraße 1
74167 Neckarsulm
GERMANY
Model no.: HG07446A/HG07446B
Version: 12/2023
Last Information Update
HG07446A/B092023-6
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>