Rayrun N12 Single Color Wireless Remote Control LED Dimmer User Manual
- June 3, 2024
- RayRun
Table of Contents
Rayrun N12 Single Color Wireless Remote Control LED Dimmer
Introduction
FEATURE
N12 single color LED dimmer is designed to drive constant voltage LED products in voltage range of DC5- 24V. The main unit works with a RF remote controller, user can adjust LED brightness on the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.
Dimension
Wiring & Indicator
Power supply input
Install positive power cable into the terminal marked with ‘+’ and negative power cable into the terminal marked with ‘-’. The controller can accept DC power from 5V to 24V, the output voltage is the same as the power supply, so please make sure the LED rated voltage is same as the power supply.
Do not power on the controller until all connection is firmly finished.
Please use remote controller to turn on the unit if it was switched to off status before previous power cut.
LED output
Connect LED fixtures to this terminal. Install positive LED load cable into the terminal marked with ‘+’ and negative cable into the terminal marked with ‘-’. Please make sure the LED rated voltage is same as the power supply and the maximum load current is lower than controller’s rated current. The controller will run into protection if the output is overloaded or short circuited. The indicator will flash red color and stop working in this case, Please check the wiring and load current to remove the fault.
Work status indicator
This indicator displays all working status of the controller. It shows
different events as following: Steady green: Normal working. Single green
blink: Command received. Long single yellow blink: Reach brightness limit. Red
flash: Overload protection. Yellow flash: Over heat protection. Green flash 3
times: New remote controller paired.
Functions
Turn ON / OFF
Press this key to switch on or off the controller. Press and hold this key
will force to switch off the controller. Main unit will memorize the on/off
status and will restore to the previous status on next power on.
Brightness control
Press the upward key to increase brightness and press the downward key to
decrease. The brightness will change smoothly when hold pressing these two
keys. The controller applies brightness gamma correction on dimming control,
makes the brightness tuning more smooth to human sense.
Remote indicator
This indicator blinks when remote controller is working. If the indicator
flash slowly when pressing keys, it means the remote battery is nearly empty
and please change the battery in this case. The battery model is CR2032.
Operation
Using the remote
The RF wireless remote signal can pass through some nonmetal barrier. For
proper receiving remote signal, please do not install the controller in closed
metal parts.
Pair a new remote controller
The remote controller and main unit is 1 to 1 paired for factory default. It’s
possible to pair maximum 5 remote controllers to one main unit and each remote
controller could be paired to any main unit. You could pair a new remote
controller to main unit by following steps:
- Plug off the power of main unit and plug in again after more than 5 seconds.
- Press and keys simultaneously for about 3 seconds, within time of 10 seconds after the main unit powered on.
Recognize current remote only
In some cases, one main unit might be paired with several remote controllers but extra remote controllers are no longer needed. User could simply pair the current using remote to main unit again, then the main unit will dis-pair all other remote controllers and recognize current one only.
Protection
The main unit has full protection function for wrong wiring, output short circuit, overload and overheat. The controller will protect itself from damage at these extreme conditions and could automatically recover when working condition is good. To avoid the protection, please ensure the LED fixtures are capable for constant voltage driving and in rated range, the cables are well connected and insulated. Also please install the controller with good ventilation and heat dissipation condition.
SPECIFICATION
Model | N12 |
---|---|
Brightness grade | 11 levels |
PWM grade | 4000 steps |
Overload protection | Yes |
Overheat protection | Yes |
Working voltage | DC 5-24V |
Remote frequency | 433.92MHz |
Remote control distance | >15m at open area |
Rated output current | 1x10A |
Controller dimension | 87x24x15mm |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>