Rayrun T111 Single Color LED Advanced RF Remote Dimmer User Guide
- June 3, 2024
- RayRun
Table of Contents
Rayrun T111 Single Color LED Advanced RF Remote Dimmer
Introduction
T111 LED dimmer is designed to drive constant voltage single color LED products such as LED strip or LED module in voltage range of DC5-24V. The receiver works with the RF wireless remote controller, user can setup LED brightness from the remote controller.
Receiver & wiring
Power supply input
The controller supply voltage range is from DC 5V to 24V. Please refer to
the print on the controller for cable polarity. The output voltage is at the
same level as the power voltage, please make sure the power supply voltage is
correct and the power wattage is capable for the load wattage. Please be noted
the positive power cable is directly connected to the output cable inside
the controller.
LED output
Connect to LED loads. Please refer to the print on the controller for cable
polarity and connect LED load with
Remote controller function
Model: T111(-H)
according polarity. Please make sure the LED rated voltage is same as the
power supply and the maximum load current is below the controller rated
current.
CAUTION: The controller might be permanently damaged if output cables
short circuit. Please ensure the cables are well insulated to each other.
Wiring diagram
Please connect the controller output to LED loads and power supply to the controller power input. The output voltage of power supply must be same as the LED load’s rated voltage. Check all cables to be well connected and insulated before power on.
Turn ON / OFF
Press ‘I’ key to turn on controller or press ‘O’ key to turn off. The controller will memorize the on/off status and will restore to the previous status on the next power on. Please use remote controller to turn on the unit if it was switched to off status before power cut.
Brightness adjust
- Press ‘+’ and ‘-‘ key to adjust brightness sequentially.
- Hold press these ‘+’ or ‘-‘ key will adjust the LED brightness smoothly.
Brightness shortcut
- Press these keys to jump to relative brightness level.
- Please note the brightness percentage is labeled as human eye sense level but not physical brightness level.
Remote indicator
This indicator blinks when remote controller is working. If the indicator flashes slowly when pressing keys, it means the remote battery is used up and please change the battery in this case. The battery type is CR2032.
Remote controller operation
Using the remote controller
Please pull out the battery insulate tape before using.
The RF wireless remote signal can pass through some nonmetal barrier. For
proper receiving remote signal, please do not install the controller in closed
metal parts.
Pair a new remote controller
The remote controller and receiver is 1 to 1 paired as
factory default. It’s possible to pair maximum 5 remote controllers to one
receiver and each remote controller could be paired to any receivers.
To pair a new remote controller, please follow two steps:
- Plug off the power of receiver and plug in again after more than 5 seconds.
- Press 100% and 60% key simultaneously for about 3 seconds, within 10 seconds after the receiver powered on.
After this operation, the LED fixture will flash quickly to acknowledge that remote pairing is accomplished.
Keep one remote and forget others
In some cases, one receiver might be paired with several remote controllers but extra remote controllers are no longer needed except current using one. User can simply pair the current using remote to receiver again, then the receiver will dis-pair all other remote controllers and recognize current one only.
Overheat Protection
The controller has overheat protection feature and it can protect itself from
damage caused by some abnormal usage such as overloading which generates
excess heat. At overheat situation, the controller will shutdown the output
for a short while and recover when temperature drops to a safe range.
Please check the output current and make sure it’s under rated level at this
situation.
Specification
| Output mode | PWM constant voltage |
|---|---|
| Working voltage | DC 5-24V |
| Rated output current | 5A |
| White brightness grade | 100 levels |
| PWM frequency | 1KHz |
| PWM physical grade | 256 steps |
| Overheat protection | Yes |
| Remote frequency | 433.92MHz |
| Remote control distance | >15m at open area |
| Power off memorizing | Yes, restore to previous mode before off. |
| Housing | Tubed for standard, ABS+Slicon for -H version |
| Controller dimension | 50x15x7mm |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>