Rayrun T120 Tunable White LED Controller User Manual
- June 3, 2024
- RayRun
Table of Contents
Rayrun T120 Tunable White LED Controller
Introduction
T112 LED dimmer is designed to drive constant voltage single color LED products such as LED strip or LED module in voltage range of DC5-24V. The receiver works with the RF wireless remote controller, user can setup LED brightness from the remote controller.
Receiver & wiring
Power supply input
The controller supply voltage range is from DC 5V to 24V. Please refer to the
print on the controller for cable polarity. The output voltage is at the same
level as the power voltage, please make sure the power supply voltage is
correct and the power wattage is capable for the load wattage. Please be noted
the positive power cable is directly connected to the output cable inside the
controller.
LED output
Connect to LED loads. Please refer to the print on the controller for cable
polarity and connect LED load with according polarity. Please make sure the
LED rated voltage is same as the power supply and the maximum load current is
below the controller rated current.
CAUTION! The controller might be permanently damaged if output cables
short circuit. Please ensure the cables are well insulated to each other.
Wiring diagram
Please connect the controller output to LED loads and power supply to the
controller power input. The output voltage of power supply must be same as the
LED load’s rated voltage. Check all cables to be well connected and insulated
before power on.
Remote controller function
Turn ON / OFF
Press ‘I’ key to turn on controller or press ‘O’ key to turn off. The
controller will memorize the on/off status and will restore to the previous
status on the next power on. Please use remote controller to turn on the unit
if it was switched to off status before power cut.
Brightness and color temperature adjust
Press keys to adjust brightness up and down, press these key to adjust color
temperature up and down.
Brightness & color temperature shortcut
Press the key with relative printing to jump to specified brightness or color
temperature setting.
Remote indicator
This indicator blinks when remote controller is working. If the indicator
flashes slowly when pressing keys, it means the remote battery is used up and
please change the battery in this case. The battery type is CR2032.
Remote controller operation
Using the remote controller
Please pull out the battery insulate tape before using. The RF wireless remote
signal can pass through some nonmetal barrier. For proper receiving remote
signal, please do not install the controller in closed metal parts.
Pair a new remote controller
The remote controller and receiver is 1 to 1 paired as factory default. It’s
possible to pair maximum 5 remote controllers to one receiver and each remote
controller could be paired to any receivers.
To pair a new remote controller, please follow two steps:
- Plug off the power of receiver and plug in again after more than 5 seconds.
- Press and key simultaneously for about 3 seconds, within 10 seconds after the receiver powered on. After this operation, the LED fixture will flash quickly to acknowledge that remote pairing is accomplished.
Keep one remote and forget others
In some cases, one receiver might be paired with several remote controllers
but extra remote controllers are no longer needed except current using one.
User can simply pair the current using remote to receiver again, then the
receiver will dis-pair all other remote controllers and recognize current one
only.
Overheat Protection
The controller has overheat protection feature and it can protect itself from damage caused by some abnormal usage such as overloading which generates excess heat. At overheat situation, the controller will shutdown the output for a short while and recover when temperature drops to a safe range. Please check the output current and make sure it’s under rated level at this situation.
Specification
- Output mode PWM constant voltage
- Working voltage DC 5-24V
- Rated output current 2x3A
- White brightness grade 11 levels
- PWM frequency 1KHz
- PWM physical grade 256 steps
- Overheat protection Yes
- Remote frequency 433.92MHz
- Remote control distance >15m at open area
- Power off memorizing Yes, restore to previous mode before off.
- Housing Tubed for standard, ABS+Slicon for -H version
- Controller dimension 50x15x7mm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>