VOLLRATH 15128 Redco Instacut 5.0 Table Top Instruction Manual

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH 15128 Redco Instacut 5.0 Table Top
Product Usage Instructions
INSTALLATION PROCEDURES
FEATURES AND CONTROLS
Technical Services
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH 15128 Redco Instacut 5.0 Table Top

VOLLRATH-15128-Redco-Instacut-5-0-Table-Top-product

Specifications

Manufacturer: Vollrath Company, L.L.C.
Model: Not specified
Country of Origin: USA
Dimensions: Not specified
Material: Not specified

Product Usage Instructions

Installation Procedures

Familiarize yourself with the parts diagram for your equipment.
Remove the pusher head assembly by sliding the pusher head off the rod guides.
Raise the bumpers approximately 2 inches (5 cm).
Loosen the thumbscrew and carefully remove the blade assembly. Discard the old blade assembly.
Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base. Tighten the thumbscrew.
Slide bumpers down guide rods to contact base. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.
Lubricate the guide bar with mineral oil or Petro Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.

Features and Controls

A: Base Assembly. Holds the guide rods and blade assembly.
B: Bumpers. Cushions the pusher head during operation.
C: Guide Rods. Guides and aligns the pusher head onto the blade set.
D: Thumbscrew. Secures the pusher head block to pusher head assembly. Secures the blade assembly to the base assembly.
E: Guides. Used for smooth and consistent operation of pusher head on the guide rods.
F: Handle. Used to lower and raise the pusher head.
G: Pusher Head Assembly. Made up of the guides, the pusher head block, and the handle.
H: Pusher Head Block. Pushes the food product through the blade set. Specifically sized to match the corresponding blade assembly.
I: Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block.

FAQ

Q: How often should I lubricate the guide bar?
A: It is recommended to lubricate the guide bar with mineral oilor Petro Gel after each use to ensure smooth operation.
Q: Can I use cooking oil to lubricate the guide bar?
A: No, cooking oil should not be used as it may become sticky and potentially damage the equipment permanently.

Redco® InstacutTM 5.0 Blade Replacement

WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.

INSTALLATION PROCEDURES

Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.

Familiarize yourself with the parts diagram for your equipment.
Remove the pusher head assembly by sliding the pusher head off the rod guides.
Raise the bumpers approximately 2″ (5 cm).
Loosen the thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
Slide bumpers down guide rods to contact base. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.
Lubricate the guide bar with mineral oil or Petro Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.

FEATURES AND CONTROLS

A Base Assembly. Holds the guide rods and blade assembly.
B Bumpers. Cushions the pusher head during operation.
C Guide Rods. Guides and aligns the pusher head onto the blade set.
D Thumbscrew. Secures the pusher head block to pusher head assembly. Secures the blade assembly to the base assembly.
E Guides. Used for smooth and consistent operation of pusher head on the guide rods.
F Handle. Used to lower and raise the pusher head.
G Pusher Head Assembly. Made up of the guides, the pusher head block and the handle.
H Pusher Head Bock. Pushes the food product through the blade set. Specifically sized to match the corresponding blade assembly.
I Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block.

www.vollrath.com

The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A. Main Tel: 800.624.2051 or 920.457.4851 Main Fax: 800.752.5620 or 920.459.6573 Customer Service: 800.628.0830 Canada Customer Service: 800.695.8560