Saffire LX-P & Saffire EVO LZ-P Exit Door Preparation

“`html

Specifications:

• Product Models: Saffire LX-P & Saffire EVO LZ-P
• Exit Door Preparation: DETEX V40
• Dimensions: Inches [mm]
• Thread Class / Filet Finish: SAE: 2A-2B, ISO: 6g / 6H
• Door Thickness: Standard Backset – X: 2.750” [70mm], Y: 1.25”
  [31.8mm] to 2.00” [50.8mm]

Product Usage Instructions:

1. Preparation

Before installation, ensure you have the correct template for
the specific lock model being installed. It is recommended to
complete a full door mockup to verify all necessary products and
parts are included.

2. Installation Steps

1. Refer to the exit device manufacturer’s installation
   instructions for the exit device and mortise lock cut-out.

2. Adjust the backset according to the exit device manufacturer’s
   instructions and the backset adjustment table.

3. For solid doors, groove as necessary for passing wires inside
   the door; for hollow doors, refer to specific tolerances.

3. Door Edge Adjustment

Ensure the backset is adjusted to both low and high bevel door
edges as per the backset adjustment table provided.

4. Symmetrical Dimensions

Dimensions are symmetrical about CL unless otherwise noted.
Refer to the specific tolerances table for dimensions marked with

.

5. Additional Notes

• Drawings are not to scale.

• Make sure to use the correct template for the specific lock
  model.

• Contact your local sales representative or authorized reseller
  for any assistance.

Frequently Asked Questions (FAQ):

1. Why is a full door mockup recommended before

installation?

A full door mockup ensures that all necessary products and parts
for a successful installation are included and helps in verifying
the correct template for the specific lock model being
installed.

2. Can the same lock model be offered with different locking

device options?

Yes, the same lock model can be offered with different locking
device options, so it is essential to select the appropriate
locking device as per your requirements.

3. Are the dimensions provided in the manual in inches or

millimeters?

The dimensions are provided in both inches and millimeters for
your convenience. Ensure to refer to the appropriate unit of
measurement based on your preference.

“`

Saffire LX-P & Saffire EVO LZ-P
DETEX V40 exit door preparation
NOTES: 1. FOR EXIT DEVICE AND MORTISE LOCK CUT-OUT REFER TO EXIT DEVICE MANUFACTURER
INSTALLATION INSTRUCTIONS. 2. BACKSET SHOWN FOR REFERENCE ONLY, ADJUST BACKSET TO EXIT DEVICE MANUFACTURER
INSTALLATION INSTRUCTIONS. BACKSET TO BE ADJUSTED TO LOW AND HIGH BEVEL DOOR EDGE AS PER BACKSET ADJUSTMENT TABLE. 3. DIMENSIONS ARE SYMETRICAL ABOUT CL UNLESS OTHERWISE NOTED. 4. GROOVE TO BE DONE ONLY IN SOLID DOORS. TO PASS WIRES INSIDE THE DOOR FOR HOLLOW DOORS. 5. REFER TO SPECIFIC TOLERANCES TABLE FOR DIMENSIONS MARKED WITH #. 6. DRAWING IS NOT TO SCALE. 7. DIMENSIONS ARE IN INCHES [mm].

2X 0.250 [6.4] 0.500 [12.7] SEE NOTE 4

3.000 [76.2]

0.250 [6.4] SEE NOTE 4
7.480 [190] 7.382 [187.5]

0.750 [19.1] 0.750 [19.1] SEE NOTE 4
0.750 [19.1]

3.438 [87.3]

BACKSET SEE NOTE 2

0.250 [6.4]

1.125 [28.6]

WARNING

· To verify lock coverage and door operation

meets expectations, dormakaba strongly

recommends completing a full door mockup. This will ensure that all necessary products and

CL

parts for a successful installation are included.

· Always validate that you have selected the

correct template for specific lock model being

installed. The same lock model can be offered

with different locking device options.

· Drawing is not to scale. Measurements are for

reference only. Not a drilling template.

· If you have any questions, please contact your

local sales representative or authorized reseller.

Saffire LX & Saffire EVO LZ series

RHR
IP-516418-11A – Rev 2

HIGH BEVEL LOW BEVEL
LOW BEVEL HIGH BEVEL

INSIDE
RIGHT LEFT HAND HAND
RIGHT LEFT HAND HAND REVERSE REVERSE
OUTSIDE

HIGH BEVEL LOW BEVEL
LOW BEVEL HIGH BEVEL

DIMENSIONS = IMPERIAL/IMPÉRIAL [MILLIMETER / MILLIMÈTRE] 3D FILE GOVERNS ALL UNSPECIFIED DIMENSIONS & GENERAL TOLERANCES APPLY / LES DIMENSIONS NON SPÉCIFIÉES SONT DÉFINIES
PAR LE FICHIER 3D ET LES TOLÉRANCES GÉNÉRALES S’APPLIQUENT GENERAL TOLERANCE, UNLESS OTHERWISE SPECIFIED TOLÉRANCES GÉNÉRALES, SAUF SI SPÉCIFIÉ AUTREMENT

THREAD CLASS / FILET FINISH / FINI SAE: 2A-2B ISO: 6g / 6H

ANGLE: 1

CHAMFER /CHANFREIN:

5

BACKSET ADJUSTMENT FOR 3° BEVEL DOOR

LOW BEVEL EDGE

DOOR THICKNESS DIMENSION X

2.750” [70mm] STANDARD BACKSET
Y

1.25” [31.8mm]

1.50 ” [38.1mm]

Y

1.75 ” [44.5mm]

2.00 ” [50.8mm]

REFERENCE
X
HIGH BEVEL EDGE

2.25” [57.2mm] 2.50” [63.5mm] 2.75” [69.9mm]

BACKSET ADJUSTMENT DIMENSION Y .032” [0.81mm] .039” [1.00mm] .046” [1.17mm] .052” [1.32mm] .059” [1.50mm] .065” [1.65mm] .072” [1.83mm]

DOOR THICKNESS
“X”

SPECIFIC TOLERANCES

DISTANCES

.030 [0.75]

HOLES

.010 [0.25]

+.030 [0.75] DIMS MARKED # -.000 [0.00]

1.500 [38.1]

3.000 [76.2]

3.500 [88.9]

2.875 [73] 0.600 [15.2]

CL
LHR

3X 0.500 [12.7] 0.313 [7.9] 0.750 [19.05]

www.dormakaba.com

05/2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>