SALTO LS5N Series Mortise Lock Installation Guide
- July 30, 2024
- SALTO
Table of Contents
LS5N Series Mortise Lock
Installation Guide
LS5N Series Mortise Lock
Mortise Lock: SALTO LS5Nxx….
PREPARING THE DOOR
Note: if a strike is already fitted in the door frame, position the lock using
the strike as reference.
(See strike position on template)
- Draw a horizontal line on both sides and edge of the door at the desired height of knob above floor.
- Draw a vertical centre line on door edge.
- Draw a vertical line on each side at the proper backset to align the template.
- Position templates on edge and sides of door.
Mark ONLY top and bottom holes of mortise cavity (A) and lock front (B) on door edge, and holes in the lateral face of the door for handles (C) and turn piece (D) (only needed in inside face). Remove template: Place lock face against door edge.
Trace outline of faceplate as guide for faceplate routing.
MORTISE THE DOOR
- Mortise door for lock body and faceplate as per instructions on template
INSTALLING THE LOCK BODY
- Insert the lock into the cavity.
- Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in place.
INSTALLING THE STRIKE
- Refer to latch to determine strike location on jamb.
- Using strike as template, mark and chisel recess.
Drill screw holes. Place strike and fasten screws.
Please check thet:
– Deadbolt and latch fit the cavities of the strike without touching it.
– Gap between door and jamb is between 2-4 mm.
| SALTO SYSTEMS, S.L.
Pol Indust. Lanbarren, c/Arkotz, 9
20180 Oiartzun-Gipuzkoa. Span 15
---|---
DOP_LS5N_01_12209
DOP_LS5N_01_179| LS5N04 / LS5N05
Mechanical lock for scape routes and/or fire doors
EN 12209:2003 + AC:2005| 3M5 10F 0B0 20
EN 179:2008| 376B1332A B/D
| SALTO SYSTEMS, S.L.
Pol Indust. Lanbarren, c/Arkotz, 9
20180 Oiartzun-Gipuzkoa. Span 15
DOP_LS5N_02_12209
DOP_LS5N_01_179| LS5N15
Mechanical lock for scape routes and/or fire doors
EN 12209:2003 + AC:2005| 3M5 10F 2B A 20
EN 179:2008| 376B1332A B/D
| SALTO SYSTEMS S.L.
Pol. Indust. Lanbarren, c/Arkotz, 9
20180, Oiartzun-Gipuzkoa. Span 15
DOP_LS5N_02_12209| LS5N25
Mechanical lock for fire doors
EN 122092003 + AC:2005| 3M5 10F 2B A 20
CE5N 1 R 0 00 ZP – STRIKE HIGH SECURITY’ CE5N 1 C E 00 IM – STRIKE DOORS HAND
LUBRICATION
All locks come from the factory pre-lubricated with grease. We recommend,
however, continued periodic lubrication of internal moving parts with
commercial quality grease (every 20.000 cycles or once a year). This can
prolong the life of the lockset by reducing excessive wear. If the lockset is
used in a harsh environment, lubrication should be applied more frequently.
*EN 179: The security characteristics of this product are essential for meeting the EN 179 standard. Modifications other than those described in these instructions are not permitted. This product is to be used on doors with maximum dimensions of 1300x2500mm (4.26’x8.2’) and weighing no more than 200kg (440lb). This product meets EN 179 only when combined with an XS4 electronic escutcheon fitted with U, H or N handles. To meet this standard, if a mechanical handle is installed on the exterior part of the door, only a mechanical fixed, non-turning knob can be used.
221011 – ED.3
– 09/02/2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>