SIGNATURE HARDWARE 98.2007 Meriden Wall Mounted Basin Mixer Instruction Manual

July 26, 2024
Signature Hardware

SIGNATURE HARDWARE 98.2007 Meriden Wall Mounted Basin Mixer

Product Information

  • Installation diagram: 48-60
  • Wall: 120
  • Hot: 180-200
  • Cold: Wall

Product Usage Instructions

Installation Procedure:

  1. 0-20
  2. 2-G1/2
  3. 120 Valve Body
  4. Plastic expansion screw – 3 Pcs
  5. Self-tapping screw – 3 Pcs
  6. Plastic plug
  7. Wall tile surface
  8. Plastic sleeves – 5
  9. Wall – Hole size 46-55
  10. Plastic sleeves – 5
  11. 70 Flange
  12. Plastic plug – 4
  13. Hole size 35-45
  14. 55 Flange
  15. Round screw nut – 7
  16. G1/2 Adapter connector – 8
  17. Outlet pipe – 10
  18. Handle – 12
  19. S2.5 Allen Key – 13
  20. Plastic spanner – 11

After use for a while, if the water outlet flow is reduced, please unscrew the aerator with a plastic spanner to clean it.

Frequently Asked Questions (FAQ)

  • Q: How often should I clean the product?
    A: It is recommended to clean the product regularly using a clean soft damp cloth only to maintain its appearance.

  • Q: What should I do if the water outlet flow is reduced?
    A: If the water outlet flow is reduced after some use, please unscrew the aerator using a plastic spanner to clean it.

INSTALLATION PROCEDURE

  1. Before installation, flush the water supply pipe to make sure all silt and debris have been removed.
  2. As Figure I showed, Connect the Cold and Hot inlet water pipe with the two G 1/2″ female threads of valve body (NO. 1). ( Wrap PTFE tape on the thread or use glue seal).
  3. Use three plastic expansion screws (NO. 2) and Self-tapping screws (NO. 3) to fix the valve body (NO. 1) on the suitable position of the wall.
  4. Pull out the plastic sleeve (NO. 5), and screw the plastic plug (NO. 4) on the tap body ( NO. 1) tightly.
  5. Open the cold and hot water supply, and check all joints and connections of the valve body for leakage. Then put on a plastic sleeve (NO. 5) after check there is no leakage.
  6. Decorate the wall (Pay attention to the size of the installation hole).
  7. As Figure II showed, unscrew the plastic plug (NO. 4), then pull out the plastic sleeve (NO. 5), then install the flange (NO. 6).
  8. As Finger III showed, unscrew the round screw nut (NO. 9), then pull out the water outlet pipe (NO. 10).
  9. Wrap PTFE tape and apply glue on the G 1/2″ thread of the adapter connector (NO. 8), Then screw the adapter connector (NO. 9) on the G 1/2″ female thread of the valve body.
  10. Install the Flange (NO. 7).
  11. Insert the outlet pipe (NO. 10) into the inner hole of the connector (NO. 8), then use a round screw nut (NO. 9) to fix the outlet pipe (NO. 10). (Pay attention that the outlet pipe (NO. 10) must be inserted in place) .
  12. Unscrew the handle spindle (NO. 16), lose the M5 screw (NO. 15) by S2. 5 Allen Key (NO. 13), then place the handle (NO. 12) on the stem spool (NO. 14). Tighten the M5 screw (NO. 15) by S2. 5 Allen Key to fix the handle (NO. 12). (Pay attention at the installation direction of handle).
  13. Screw the handle spindle (NO. 16) on the handle (NO. 12).
  14. Open the cold and hot water supply, and check all joints and connections for leakage.

Guarantee & Aftercare

When installing or using tools, extra care must be taken to avoid damaging the finish or fitting. To maintain the appearance, please ensure it is cleaned regularly using a clean soft damp cloth only. Abrasive cleaners or detergents must not be used as they may cause surface deterioration. The company provides a guarantee against faulty material or manufacture excluding serviceable parts, providing they have been installed, cared for, and used under our instructions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Signature Hardware User Manuals

Related Manuals