Signature Hardware 953462 Beringer Pendant Light Single Light Instruction Manual

: June 8, 2024
: Signature Hardware

Table of Contents

BEFORE YOU BEGIN
GETTING STARTED
ADDITIONAL QUESTIONS?
FOR YOUR SAFETY
CARE INSTRUCTIONS
TOOLS AND MATERIALS:
INSTALLATION (FIG 1)
Documents / Resources

Hardware 953462 Beringer Pendant Light Single Light
Instruction Manual

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric ﬁxtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping damage.
If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.
com or by emailing support@siganturehardware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

ADDITIONAL QUESTIONS?

Still need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut oﬀ, either the fuse is removed or the circuit breaker is shut oﬀ. You don’t need special tools
to install this ﬁxture. Be sure to follow the steps in the order given. Under no circumstances should a ﬁxture be hung on house electrical wires, nor should a swag type ﬁxture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualiﬁed electrician.

CARE INSTRUCTIONS

To clean, wipe ﬁxture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS:

| Safety goggle
---|---
| Step ladder
| Wire strippers
| Wire cutters
| Phillips screwdriver
| Flathead screwdriver
| Electrical tape
| Light Bulb (A19 60 watt maximum)

INSTALLATION (FIG 1)

Signature Hardware 953462 Beringer Pendant Light Single Light - Fig
7

Carefully push ﬁxture wires up through bottom of center stem (M). Pull ﬁxture wires out of top of center stem (M). Pull ﬁxture wires taut. Screw bottom of center stem (M) into top of ﬁxture body (O).
Attach one locking link (G) onto loop on top of center stem (M
Determine desired hanging height of ﬁxture. Cut chain (H) to length to achieve desired height.
Attach chain link at end of chain (H) onto locking link (G) on loop on top of center stem (M).
Weave ﬁxture wires through chain (H), skipping every other chain link.
Slip threaded ring (F) down over end of chain (H) and ﬁxture wires.
Slip hole in canopy (D) over end of chain (H) and ﬁxture wires.
INSTALLATION (FIG 2)
Carefully pull house wires down out of junction box so house wires are easily accessible to connect ﬁxture wires.
Position mounting bracket (A) so longest end of threaded pipe (W) attached to mounting bracket (A) is pointing down towards ﬂoor.
Align holes in mounting bracket (A) with holes in junction box.
Thread each junction box screw (B) into appropriate holes in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
Thread screw collar loop (E) onto threaded pipe (W). Tighten screw collar loop (E) up against ﬁrst hexnut on threaded pipe (W).
Connect Black or Red Supply Wire (Lead Wire) to:| Connect White Supply Wire (Neutral Wire) to:
---|---
Black wire| White wire
Parallel wire (round or smooth)| Parallel wire (square or ridged)
Clear brown, gold or black wire without trace r| Clear brown, gold or black wire with trace r
Insulated wire (other than green) with copper conductor| Insulated wire (other than green)
with silver conductor

When parallel wires are used, the neutral wire is ridged down its length and the other wire is round and smooth (see illus.).

INSTALLATION (FIG 3)
Signature Hardware 953462 Beringer Pendant Light Single Light - Fig
8

Strip 3/4” of insulation from ends of ﬁxture wires.
Push ﬁxture wires up through hole in screw collar loop (E) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull ﬁxture wires so they are easily accessible to connect to house wires.
To aid in connecting ﬁxture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (E).
Twist the end of ﬁxture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of ﬁxture black wire and the end of house black wire together.
Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure
connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to ﬁxture ground wire. Twist the end of ﬁxture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
Note: If you have electrical questions consult your local electrical code for approved grounding methods
After wires are connected, carefully tuck wires inside junction box.
INSTALLATION (FIG 4)
Remove second locking link (G) from last link on chain (H) and screw collar loop (E).
Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (E). Position canopy (D) up against ceiling.
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (E). Tighten threaded ring (F) to secure ﬁxture to ceiling.21. Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (E)
Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of ﬁxture.
WARNING: DO NOT exceed maximum bulb wattage.

1.855.715.1800
signaturehardware.com

Documents / Resources

| Signature Hardware 953462 Beringer Pendant Light Single Light [pdf] Instruction Manual
953462 Beringer Pendant Light Single Light, 953462, Beringer Pendant Light Single Light, Pendant Light Single Light, Light Single Light, Single Light
---|---