SIGNATURE HARDWARE 456743 Bowden Barn Door Hardware Instruction Manual

SIGNATURE HARDWARE 456743 Bowden Barn Door Hardware

Product Specifications

• Product Name: Bowden Barndoor Hardware with 78 Track
• SKU: 950683
• Rail Length: 78-3/4 inches (1,981 mm)

Product Usage Instructions

Before You Begin
It is recommended to consult a professional if you are unfamiliar with installing plumbing fixtures. Make sure to observe all local plumbing and building codes. Unpack and inspect the product for shipping damage before starting the installation.

Getting Started
Ensure you have all the required materials for installation, including a Phillips screwdriver, level, drill, drill bits, bolts, door hangers, washers, door stops, rail wall spacers, lag bolts, and door guides.

Installation Steps

1. Layout your door and hardware on the floor first to determine spacing.
2. Ensure the rail is level to prevent the door from moving on its own.
3. Mount the rail according to the provided Rail Mounting Instructions. All rail mounts must be screwed into a solid wood header.
4. If stops may end up inside end mounts, place stops on the rail before mounting the rail.

Frequently Asked Questions (FAQ)

• Q: What should I do if I find shipping damage?
  A: If any shipping damage is found, contact our Customer Relations team at 1-855-715-1800 for assistance.

• Q: How do I ensure the rail is properly installed?
  A: Follow the provided Rail Mounting Instructions carefully and ensure all rail mounts are securely screwed into a solid wood header to prevent any issues during usage.

BOWDEN
BARNDOOR HARDWARE WITH 78” TRACK
ACCESORIOS PARA PUERTAS CORREDIZAS CON RIEL DE 1,981 MM
PORTE DE GRANGE AVEC RAIL DE 2 M (78 PO)
SKU: 950683

BEFORE YOU BEGINBEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the hardware, wall, door, or for personal injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team at 1-855-715-1800.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

For Warranty information, please visit: signaturehardware.com/services/warranty

TOOLS AND MATERIALS

PARTS INCLUDED

Rail Mounting Instructions Locating the Mounting Position
Recommend that you layout your door and hardware on the floor first to determine spacing.

Installing the Rail

Note: Stops may end up inside end mounts depend-ing on your hanger placement, if so place stops on rail before mounting rail.

Important: All rail mounts must be screwed in to a solid wood header.

Hanger Mounting Instruction

• Hanger postion from the edge can vary based on your door design.
• Position shown is for a flat surface door, you may have to adjust to center the hanger onto the vertical stiles of your door.

\ Anti-Jump Disks Mounting Instructions

• Anti-Jump Disks keep your door from accidentally coming of the rail.
• They are installed of set with the screw outside the rail in case you need to remove the door later.

Bottom Guide Mounting Instructions

• The guide stabilizes the door by keeping the bottom from swinging.
• This step will require hanging and removing the door to measure and install the guides.

Final Door Hanging Anti-Jump Disk Lockdown

Door Stop Positioning Instructions
Adjust your door stops to your desired position and lock down your door stops with the provided allen wrench.

Optional Soft-Close Hardware

• Determine left and right hand closer
• The closer mounts behind the rail.
• Position left side soft closer close to the door stop and lock it to the rial by tightening down the two set screws on each mounting bracket.
• Position right side soft closer close to the door stop and lock it to the rail by tightening down the two set screws on each mounting bracket.

Optional Soft-Close Hardware

• Mark the position of each trigger.
• Remove the door and attach the triggers with the supplied screws.

Optional Soft-Close Hardware
Adjust the vertical catch plate of the trigger to securely seat in the trigger catch of the closer.

Test Your Door

Door should slide smoothly in both directions.

customer service: 1.855.715.1800 signaturehardware.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>