BRISTAN D7 Blitz Chrome Finish Basin Mixer Tap with Clicker Waste Instruction Manual
- June 5, 2024
- BRISTAN
Table of Contents
D7 Blitz Chrome Finish Basin Mixer Tap with Clicker Waste
Instruction Manual
Specifications
Maximum Inlet Temperature
60-65°C Recommended
Dynamic Water Pressure
Inlet Connections
M10x300mm Flexi Tails
Tools You’ll Need
Prior to Installation
All products manufactured and supplied by Bristan are safe provided they are
installed, used correctly, and receive regular maintenance in accordance with
these instructions.
This product has been tested by the Water Regulations Advisory Scheme (WRAS)
and satisfies the requirements of the Water Supply (Water Fittings)
Regulations 1999 and current bylaws. For full Installation Requirements &
Notes (IRN) please visit wras.co.uk/directory.
We recommend isolation valves be fitted to the inlet water supplies to ensure
ease of future maintenance.
Before installing these taps the water supply must be thoroughly flushed in
order to remove any swarf, solder, etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Pack Contents
Spare Parts
To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product.
http://www.bristan.com/products/kitchen-taps?code=GLL%20PROSNK%20C
Installation
-
Screw the Flexi tails into the bottom of the mixer body by hand only. (DO NOT OVERTIGHTEN)
TIP: Profit mixer to the basin before fitting. -
Place the plinth and the washer over the hole in the basin and feed the mixer body and tails through.
-
Secure to basin using fixing kit, connect the hot and cold water supplies to the threaded tails.
**REMEMBER Hot on the left, cold on the right!
Use flat-faced isolation valves to isolate the water supplies.
IMPORTANT:** Turn on the water supply for a few minutes and check all joints and connections for any leaks. -
Fit the waste above the basin with the top washer.
-
Secure waste under the basin with backnut and bottom washer
Waste Operation
Push the center down to close the waste. Push again to open and release the contents of the basin.
Operation
General Cleaning
Bristan products are made from premium materials, with hand polishing and
electroplated finishes.
Your taps or shower should be regularly cleaned with warm water, a mild pH-
neutral liquid soap, and polished with a soft cloth. Any residues from soap,
toothpaste, shampoos, and shower gels can cause blemishes if not rinsed off
straight after use. Household bleaches and cleaners contain harsh chemicals
and may damage the surface finish. Avoid using abrasive cloths, scouring pads,
scrub sponges, steel wool, or anything similar.
Some surfaces such as nickel and pewter may be affected by the dye found in
some cloths, so it is also important to avoid hanging clothes on spouts.
Maintenance – Clean/Replace Outlet
-
- Place aerator parts in a suitable solution and soak until fully de-scaled.
-
Reverse the maintenance steps to replace the aerator.
Maintenance – Cartridge Cleaning
Troubleshooting
| Symptom | Cause | Remedy |
|---|
No flow or low flow
rate| Partially closed isolation valve.| Open isolation valve.
Instantaneous water heater cycles on and off as the flow rate or pressure is
too low.| Increase water flow rate or pressure through the system.
The Head of water is below the minimum distance required.| Refer to the
specification for the minimum distance required.
Hot or cold water being drawn off elsewhere causes pressure changes or
instantaneous boiler temperature changes.| Do not use other water outlets when
using the taps.
Airlock or partial blockage in the supply pipework.| Flush through pipework to
ensure the removal of debris and any airlocks.
Water dripping from taps| This is normal for a short time after using the
taps.| This is caused by residual water tension, the build-up of water in the
tap body.
If water continues to drip.
possibly due to the ceramic disc valves| Remove valves and clean them, refer
to the ‘Maintenance’ section before starting any maintenance.
Taps do not turn on| Closed isolation valve.| Open isolation valve.
The mains water supply was turned off.| Turn on the mains water supply.
Notes
Please use this space for any notes you or your installer may have regarding the installation/plumbing of this product.
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offer solid guarantees on all our products, effective from the
date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your
product.
Alternatively, visit
www.bristan.com/register to register your
product via a computer.
For full guarantee terms and conditions visit
www.bristan.com/guarantees.
http://www.bristan.com//register
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>