Fujitsu fi-760PRB Imprinter User Guide

P3PC-6112-03EN
fi-760PRB Imprinter
Operator’s Guide

Introduction

The fi-760PRB Imprinter is an optional unit to be used with the fi-7600 image scanner.
This manual explains installation and connection, basic operations, and regular maintenance of the fi-760PRB
Imprinter. Use the product correctly according to this manual.
For how to use the fi-7600 image scanner, refer to “fi-7600/fi-7700/fi-7700S Image Scanner Operator’s Guide” contained in the setup DVD-ROM included in the package.
We hope that this manual helps you make the most of the imprinter. February 2022

Safety Information

The “Safety Precautions” manual that is supplied with the scanner contains important information about the safety and the correct way of using this product. Make
sure that you read and understand it before using this product.

Manufacturer

PFU Limited
YOKOHAMA i-MARK PLACE, 4-5 Minatomirai
4-chome, Nishi-ku, Yokohama-shi, Kanagawa 220-8567 Japan.
© PFU Limited 2017-2022

Trademarks

PaperStream is a registered trademark of PFU Limited in Japan.
Other company names and product names are the registered trademarks or trademarks of the respective companies.

Abbreviations Used in This Manual

The operating systems and products in this manual are indicated as follows.

Windows® 7 Professional (32-bit/64- bit)
Windows® 7 Enterprise (32-bit/64-bit)| Windows 7 (1)
Windows Server® 2012 Standard (64-bit)| Windows Server 2012 (1)
Windows Server® 2012 R2 Standard (64-bit)| Windows Server 2012 R2 (1)
Windows® 8.1 (32-bit/64-bit)
Windows® 8.1 Pro (32-bit/64-bit) Windows® 8.1 Enterprise (32-bit/64-bit)| Windows 8.1 (1)
Windows° 10 Home (32-bit/64-bit) Windows° 10 Pro (32-bit/64-bit) Windows° 10 Enterprise (32-bit/64-bit) Windows° 10 Education (32-bit/64-bit)| Windows 10 (1 )
Windows Server® 2016 Standard (64-bit)| Windows Server 2016 (1)
Windows Server® 2019 Standard (64-bit)| Windows Server 2019 (1)
Windows Server® 2022 Standard (64-bit)| Windows Server 2022 (1 )
Windows® 11 Home (64-bit) Windows° 11 Pro (64-bit)
Windows® 11 Enterprise (64-bit) Windows° 11 Education (64-bit)| Windows 11 *
(1)
PaperStream IP (TWAIN) PaperStream IP (TWAIN x64) PaperStream IP (ISIS) Bundle| PaperStream IP driver
fi-760PRB Imprinter| imprinter
fi-7600 image scanner| scanner
fi-7600/fi-7700/fi-7700S Image Scanner Operator’s Guide| Operator’s Guide

*1: Where there is no distinction between the different versions of the above operating system, the general term “Windows” is used.
Arrow Symbols in This Manual
Right-arrow symbols ( ) are used to separate icons or menu options you should select in succession. Click [Start] menu [Control Panel].
Screen Examples in This Manual
Microsoft product screenshots are reprinted with permission from Microsoft Corporation.
The screen examples in this manual are subject to change without notice in the interest of product development.
If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the user’s manual of the scanner application that you are using.
The screenshots used in this manual are of Windows 7 or Windows 10. The actual windows and operations may differ depending on the operating system. Also note that with some scanner models, the screens and operations may differ from this manual when you update the software. In that case, refer to the manual provided upon updating the software

Chapter 1 Preparations

1.1 Checking the Package Contents
Check the package contents list that is included in the imprinter package box to make sure that all items are included in the package.
If anything is missing or damaged, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
Use this product and accessories carefully.
1.2 Names of Component Parts

Imprinter Unit
Attachment Guide

• Imprinter with Scanner
  Front
  

The scanner has an operator panel on each side.

• LCD
• [Menu] Button
• [ ] Button/[ ] Button
• [Stop/Clear] Button
• [Scan/Enter] Button
• [Power] Button

Back

Inside

Chapter 2 Installation

2.1 Installing the Imprinter
Install the imprinter as follows:
ATTENTION
Do not move the scanner with the imprinter installed. The imprinter may be damaged.

1. Turn off the scanner power and disconnect the
   power cable.

2. Remove the stacker from the scanner.
   1 Check that the stacker is placed in the lower position.
   You can lower the position of the stacker by tilting it upwards a little.
   2 Hold the center ( 1 ) of the stacker and slightly 2 bend it to remove the right side ( 2) of the stacker from the slot in the direction of the arrow.
   ATTENTION
   •  You must remove the stacker before installing the imprinter.
   • Do not pull forcibly, since this might damage the stacker.

3. Attach the attachment guide to the scanner.
   1 Make sure that the direction of the attachment guide is the same as direction shown in the following figure.
   2 Look into the scanner from below to check the position of the bar.
   3 Align the attachment guide with the bar.4 Lift the attachment guide from underneath to attach it. ATTENTION
   Confirm the following after attaching the attachment guide.

   • The attachment guide is not tilted.
   • The attachment guide is fitted in the scanner, and not overhanging.
     Good: The attachment guide is properly attached.

Bad: The attachment guide is tilted.

Bad: The attachment guide is overhanging.

HINT
Removing the Attachment Guide
To remove the attachment guide, press your fingers against the attachment guide and slide it downward.

4. Attach the scanner onto the imprinter.
   Hold the scanner above the rear of the imprinter and gently lower it onto the base of the imprinter until it fits in place. ATTENTION
   Be careful not to get your fingers caught.

5. Raise the locks (two locks on the back side).

6. Turn the locks inside (two locks on the back side).

7. Connect the EXT cable to the connector on the back of the scanner. ATTENTION
   The imprinter will not work if the EXT cable is not connected to the scanner. Scanning when the EXT cable is not connected can cause documents to jam inside the imprinter.

8. Install the stacker removed from the scanner (in procedure 2) to the imprinter. Insert the protrusion on the right side of the stacker into the slot and then push the left  ide of the stacker along the slot in the direction of the arrow.

9. Connect the power cable to the scanner.

2.2 Loading the Print Cartridge
Load the print cartridge as follows:
ATTENTION

• When installing the print cartridge, install it properly.
• When you do not use the imprinter for a long time, remove the print cartridge from the imprinter. Ink will be consumed every time the scanner is powered-on even if printing is not done.

1. Turn off the scanner.

2. Place your hand in the middle part of the print cartridge and open it as shown below.

3. Remove the tape that holds the print cartridge holder and the paper guides.

4. Lift the print cartridge holder by pinching the lever with your fingers as shown below.

5. Take out the print cartridge from the bag.

6. Remove the protection tape on the print cartridge. ATTENTION
   Do not touch the metal part of the print cartridge nor put the tape back again.

7. With the tab on the print cartridge facing right, put the print cartridge into the holder. ATTENTION
   Be careful not to let the print cartridge catch the print circuit film to avoid damaging the film.

8. Bring down the arm of the print cartridge holder down gently until it locks in and set the print cartridge in place.
   Make sure that the catches (both sides) on the arm latch onto the print cartridge firmly.

9. Move the print cartridge to an appropriate printing position.
   The print cartridge should be positioned within the section where the document will pass through.

10. Close the print cartridge cover.

2.3 Test Print
After loading the print cartridge, check if the printing operation works normally.
HINT
For details about the operator panel, refer to the Operator’s Guide provided with the scanner.

1. Push the [Power] button of the operator panel of the scanner.
   The [Ready] screen is shown on the LCD.

2. Load a blank document in the scanner.
   HINT
   • Use A3 or Double Letter size blank paper. If the paper size is smaller, printing may not be completed successfully.
   • Confirm that the print cartridge is positioned within the document width.

3. Press the [Menu] button. The [Settings Menu] screen is shown on the LCD.

4. Select [3: Test Print] by pressing the [ ] button or the [ ] button, and confirm the selection by pressing the [Scan/Enter] button.
   The [No. of Sheets Scanned] screen is shown on the LCD.
   ATTENTION
   If the Imprinter is disconnected or not connected properly, [Cannot use this function because the Imprinter is not connected.] is shown on the LCD.

5. Select [1: Single Sheet Only] or [2: Multiple Sheets] by pressing the [ ] button or the [ ] button, and then confirm the selection by pressing the [Scan/ Enter] button.
   When [2: Multiple Sheets] is selected, printing is performed for all sheets set in the scanner.
   The [Print Pattern] screen is shown on the LCD.

6. Select a print pattern by pressing the [ ] button or the [ ] button, and then confirm the selection by pressing the [Scan/Enter] button.
   HINT
   Below are the print test patterns:
   Test Pattern 1 (Horizontal):
   ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^`0000 0000
   Test Pattern 2 (Horizontal): abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
   Test Pattern 3 (Horizontal):
   !”#$%&'()*+,-./0123456789:;<=>?@00000000
   Test Pattern 4 (Vertical):
   ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^`0000 0000
   Test Pattern 5 (Vertical):
   abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
   Test Pattern 6 (Vertical):
   !”#$%&'()*+,-./0123456789:;<=>?@00000000
   The numbering section “00000000” increases in increments of one, starting from 0 (zero).Test Pattern Print Sample
   The [Test Print] screen is shown on the LCD.

7. Select [1: Yes] by pressing the [ ] button or the [ ] button, and then confirm the selection by pressing the [Scan/Enter] button.
   The blank sheet is fed into the scanner, and the imprinter will print out a print test pattern leaving a 5 mm gap (with an allowance of 4 mm inwards or outwards) from the edge of the document.

8. To finish the print test, press the [Power] button on the operator panel of the scanner to turn off the power of the scanner.
   ATTENTION
   Do not move the imprinter or give it a jolt while printing. Printing may be out of order.

Chapter 3 Basic Operation

3.1 Setting the Print Position
Set the print position in the following steps:

1. Open the print cartridge cover.

2. Move the print cartridge to an appropriate printing position.
   Hold the print cartridge as below, and slide it to the left or right within the document width to set it at a suitable print starting position. HINT
   • The triangle-shaped protrusion on the print cartridge holder indicates the print head. Use the protrusion as a guide for the print position.
   •  You can find the document size markings on the imprinter above the print cartridge. Use the markings as a guide for the document width.
   •  Load the actual document in the scanner and make sure that the print cartridge is positioned within the width of document.

3. Close the print cartridge cover.

3.2 Using the Paper Guides
When documents have curled edges like below, use the paper guides to prevent paper jams.Move the paper guides to the positions where the edges of documents pass through in the following steps:
1 Load documents in the scanner.
2 Open the print cartridge cover.
3 Slide the paper guides and align them with the edges of the document. ATTENTION
Be careful not to let the paper guides come into contact with the print circuit film to avoid damaging the film. HINT
When you want to perform a print on the left or right margin of a wide document, the paper guide may get in the way. In this case, remove the paper guide and attach it to a place near the center where space is available ( 1 ). After that, move the print 2 cartridge to the left or right margin ( 2). •When the print position is on the right margin• When the print position is on the left margin Removing the Paper Guides
To remove the paper guides, pinch the paper guide with your fingers and pull it out as shown below.

Attaching the Paper Guides

1. Place the paper guide as shown in the figure below.
   Make sure that the paper guide is under the metal wheel.

2. Push the head of the paper guide until it fits in well.

3.3 Print Setup
You can configure settings for the imprinter by using the scanner driver’s setup window.
HINT
How to run the scanner driver differs depending on the application.
For details, refer to the manual or help of the application being used.
HINT
The following items can be specified. For details, refer to the help of the PaperStream IP driver.

• Imprinter status (on or off)
• Whether or not the setup dialog box is displayed
• Whether the PaperStream IP driver is synchronized with the Digital Endorser
• Printing settings (such as font type, direction, the print starting position, character strings to be printed, and initial, increased and decreased values for the counter)

3.4 Replacing the Print Cartridge
The print cartridge is a consumable.
Replace the print cartridge as follows:
ATTENTION

• When the following message appears, replace the print cartridge as soon as possible. If you continue to print without replacing the cartridge, your print output will be faded.
• When replacing the print cartridge, make sure it is installed properly.

1. Turn off the scanner.

2. Place your hand in the middle part of the print cartridge and open it as shown below.

3. Lift the print cartridge holder by pinching the lever with your fingers as shown below.
   

4. Remove the old print cartridge.

5. Remove the protection tape on the new print cartridge. ATTENTION
   Do not touch the metal part of the print cartridge nor put the tape back again.

6. With the tab on the print cartridge facing right, put the print cartridge into the holder. ATTENTION
   Be careful not to let the print cartridge catch the print circuit film to avoid damaging the film.

7. Bring down the arm of the print cartridge holder down gently until it locks in and set the print cartridge in place.
   Make sure that the catches (both sides) on the arm latch onto the print cartridge firmly.

8. Move the print cartridge to an appropriate printing position.
   The print cartridge should be positioned within the section where the document will pass through. ATTENTION
   Depending on the position of the print cartridge, printing may not fit within the document when printing close to the document edge.

9. Close the print cartridge cover.

10. Turn on the scanner.

11. Reset the ink counter in the following procedure.

ATTENTION
Be sure to reset the ink counter after replacing the print cartridge

1. Display the [Software Operation Panel] window.
   Windows Server 2008 R2/Windows 7
   Click [Start] menu [All Programs] [fi Series] [Software Operation Panel].
   Windows Server 2012
   Right-click the Start screen, and select [All apps] on the app bar [Software Operation Panel] under [fi Series].
   Windows Server 2012 R2/Windows 8.1
   Click [ ] on the lower left side of the Start screen and select [Software Operation Panel] under [fi Series].
   To display [ ], move the mouse cursor.
   Windows 10/Windows Server 2016/Windows Server 2019/Windows Server 2022
   Click [Start] menu [fi Series] [Software Operation Panel].
   Windows 11 Click [Start] menu [All apps] [fi Series] [Software Operation Panel].

2. Click [Device Setting] from the list on the left, and The value of the counter is set to 100.

3. Click the [OK] button on the [Software Operation Panel] window.

4. A message appears. Click the [OK] button.
   The [Software Operation Panel] window closes, and the ink counter is cleared.

3.5 Removing Jammed Documents
If a document jams, remove the jammed document as follows:
ATTENTION
Open the ADF and the print section to remove the jammed document. Do not pull out the document forcefully.

1. Remove the documents from the ADF paper chute (feeder).

2. Hold the middle part of the print section, and open it as shown in the figure. ATTENTION
   When you open the ADF, be sure to open the print section beforehand.

3. Open the ADF.

4. Remove the jammed document.

5. Close the ADF.

6. Hold the middle part of the print section, and close it as shown in the figure. ATTENTION
   • Make sure that the ADF is closed before you close the print section.
   • Be careful not to get your fingers caught.

Chapter 4 Daily Care

4.1 Cleaning the Print Cartridge
Ink stains stuck to the nozzle plate of the print cartridge or leaving the imprinter unused for a while may cause poor print quality due to a clogged nozzle. If your imprinter has these types of trouble, clean the nozzle plate of the print cartridge.
ATTENTION
For cleaning, use a dry lint-free cloth, and gently wipe off the excess ink from the surface of the nozzle plate. (Do not use a tissue.)
HINT
If the nozzle is still clogged after cleaning the print cartridge, replace it with a new cartridge.

1. Turn off the scanner.

2. Remove the print cartridge.
   (Refer to “3.4 Replacing the Print Cartridge” (page 14).) ATTENTION
   Be careful not to touch the nozzle plate or the contact part with your hand as this may cause poor print quality or contact errors.

3. Wipe off the excess ink on the nozzle plate gently.

4. Make sure that the excess ink is removed and then reinstall the print cartridge.
   (Refer to “3.4 Replacing the Print Cartridge” (page 14).)
   ATTENTION
   When installing the print cartridge, install it properly.

4.2 Cleaning the Imprinter
While you use the imprinter frequently, ink sticks to the print cartridge holder base which makes the paper dirty. As a part of daily maintenance, clean the print cartridge holder base by following the procedure below.
ATTENTION
When cleaning, use an absorbent cloth or a waste cloth, and gently wipe off the ink.
If the ink is dried, gently wipe it with a moistened cloth. (Since the ink is water soluble, it can be cleaned with water.)

1. Turn off the scanner.

2. Remove the print cartridge.
   (Refer to “3.4 Replacing the Print Cartridge” (page 14).)

3. Open the print section.

4. Clean the print cartridge holder base by pressing a cloth or a waste cloth gently on it to wipe off the ink. ATTENTION
   When cleaning, be careful not to touch the metal wheels located at the print section.

5. Confirm that the ink is removed and then close the print section.

6. Reinstall the print cartridge.
   (Refer to “3.4 Replacing the Print Cartridge” (page 14).)

4.3 Cleaning the Rollers
When ink or paper dust is stuck on the imprinter feed roller surfaces, documents may not feed smoothly. To prevent feed problems, clean the roller surfaces regularly.
ATTENTION
It may take a long time to dry if an excessive amount of Cleaner F1 is used. Use it in small quantity. Wipe off the cleaner completely to leave no residue on the cleaned parts.
HINT
The recommended cleaning cycle is every 5,000 sheets. The actual cleaning cycle may be shorter depending on how often the imprinter is used and the documents.

1. Open the print section.

2. Clean the rubber rollers.
   Clean the rubber rollers (eight in total) under the feeding section.Gently wipe the dirt and dust off the surface of the rollers with a cloth moistened with Cleaner F1. Clean the entire surface of the rubber rollers as you rotate them manually.
   ATTENTION
   When cleaning, be careful not to touch the metal wheels located at the print section.
   

3. Clean the plastic rollers.
   Clean the two plastic rollers (black) at the print section.Rotate the rollers manually while gently wiping the dirt and dust off the surface of the rollers with a cloth moistened with Cleaner F1.

4. Confirm that the dirt is removed and then close the print section.

4.4 Cleaning Materials

Cleaner Fl
| PA03950-| Volume: 100 ml
Cleaning Wipe
| PA03950-| 24 packets

*1: Pre-moistened with Cleaner F1. It can be used instead of moistening a cloth with Cleaner F1.
ATTENTION
In order to use the cleaning materials correctly and safely, read the precautions on each product thoroughly.
For information about the cleaning materials, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.

Chapter 5 Error Messages

This chapter explains the imprinter error messages.
Error codes and error messages are displayed on the LCD. Refer to the error codes and the error messages that are displayed for troubleshooting.
HINT
For details on the error messages and other errors, refer to the Operator’s Guide provided with the scanner.

1.Remove the jammed document from the imprinter.
2.Make sure that the document is an appropriate one for scanning with the imprinter.
3.Clean the rollers.
U5:4A (*1)| Imprinter Cover Open| Close the print section of the imprinter, and load the document again.
U6:B4| Print cartridge not installed| No print cartridge is installed.
Check if the print cartridge is installed correctly.
U7:B9| Imprinting area error| Adjust the imprinting start position and the imprinter strings to fit the imprinting area in the document.
Al :B3| Imprinter error (communication timeout)| An error occurred in the imprinter. Try the following:
1.Confirm that the EXT cable of the imprinter is connected properly to the EXT connector on the back of the scanner.
2.Check if the print cartridge is installed correctly.
3.Turn the scanner off then back on.
If the problem persists, write down the displayed error code and contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
A3:B6| Imprinter error (EEPROM)
A4:B8| Imprinter error (ROM)
A2 :B5| Imprinter error (print head)| An error occurred in the imprinter. Try the following:
1.Confirm that the EXT cable of the imprinter is connected properly to the EXT connector on the back of the scanner.
2.Check if the print cartridge is installed correctly.
3.If you have a new print cartridge, replace the old print cartridge with the new one.
4.Turn the scanner off then back on.
If the problem persists, write down the displayed error code and contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
H6:B1| Imprinter system error| An error occurred in the imprinter.
Turn the scanner off then back on.
If the problem persists, write down the displayed error code and contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.

*1: When you open the imprinter print section while the scanner is in standby, only an error message will appear without an error code. Also, note that buttons on the operator panel are disabled while the imprinter print section is open.

Chapter 6 Specifications

Item|

Specification

---|---
Printing Method| Thermal inkjet printing
Print Timing| Post printing, back surface printing
Printing Characters| Alphabet: A to Z. a to z
Numeric characters: 0, 1 to 9
Symbols: I’M 8,1)•+,-. /:;<=>7@[¥1^_'(1)—
Maximum Number of Characters per Line| Maximum of 43 digits
Print Orientation| Normal. Bold: 0°. 180° (horizontal), 90°. 270° (vertical)
Narrow: 0°. 180° (horizontal)
Character Size| Normal, Bold: Height 2.91 x width 2.82 mm/0.1146 x 0.1110 in. (horizontal orientation),
Height 2.82 x width 2.91 mm/0.1110 x 0.1146 in. (vertical orientation) Narrow: Height 2.91 x width 2.12 mm/0.1146 x 0.0835 in. (horizontal orientation)
Character Pitch| 3.53 mm/0.1390 in. (Normal, Bold), 2.54 mm/0.10 in. (Narrow)
Font Style| Regular, Bold
Character Width| Normal. Bold, Narrow
Document That Can Be Scanned| Documents that can be scanned with the scanner
For details. refer to the Operators Guide provided with the scanner. Note that the paper size and weight are as follows:
•Maximum size (width x length) 304.8 mm x 431.8 mm/12.0 in. x 17.0 in.
•Minimum size (width x length) 50.8 mm x 69 mm/2.00 in. x 2.72 in.
•Paper weight
52 to 128 g/m2 (14 to 34 lb)
ATTENTION
•Documents with glossy surface such as thermal paper, thermal transfer paper, coated paper, and art paper take longer time for the ink to dry and may cause poor print quality. The imprinter must be cleaned more frequently if you use these types of papers.
•Thick plastic documents such as credit cards and a Carrier Sheet cannot be scanned when the imprinter is installed.
Printing Area| | A = 5 mm
B = 5 mm
C = 5 mm
D = 5 mm (0.20 in.)
ATTENTION
Do not print within 5 mm from the edge of the document
Accuracy of Printing Position| ±4 mm/0.16 in. from the starting point for feed direction
Item| Specification
---|---
Dimension| Without scanner 360 (W) x 435 (D) x 228 (H) (mm)H4.17 (W) x 17.13 (D) x 8.98 (H) (in.) With scanner: 360 (W) x 435 (D) x 264 (H) (mm)/14.17 (W) x 17.13 (D) x 10.39 (H) (in.)| Excluding the interface cable, ADF paper chute (feeder) and stacker
Weight| 4.2 kg (9.26 lb)
Ambient Condition| Temperature: 10 to 35°C (50 to 95 °F), Humidity: 20 to 80%
Consumable| Print cartridge (PART No.: CA00050-0262) (See “Contact for Purchasing Consumables or Cleaning Materials” (page 23).) The printable number of characters: 4,000,000 characters (The printable number of characters differs depending on the characters to be printed.)
Replacement cycle: 4,000,000 characters or six months after opening (A print cartridge has a specific expiration date, and the expiration period differs whether the package is opened or not. Start using the print cartridge before the expiration date that is written on the package.)

Contact for Inquiries

Refer to the contact list on the following web page: https://imagescanner.fujitsu.com/r/ctl/

• Image Scanner fi Series
  For other inquiries regarding the scanner, refer to the following web page:
  https://www.fujitsu.com/global/support/products/computing/peripheral/scanners/fi/
  If the solution to your problem cannot be found on the above web page, refer to the contact information for your Fujitsu office on the following web page:
  https://www.fujitsu.com/global/about/resources/shop/computing/peripheral/scanners/index.html

• Contact for Purchasing Consumables or Cleaning Materials https://imagescanner.fujitsu.com/r/ctl/

fi-760PRB Imprinter
Operator’s Guide
P3PC-6112-03EN
Issue date: February 2022
Issued by: PFU Limited

• The contents of this manual are subject to change without notice.
• PFU Limited assumes no liability for incidental or consequential damages arising from the use of this product, and any claims by a third party.
• Copying of the contents of this manual, in whole or in part, as well as the scanner applications is prohibited under the copyright law.

References

• sp-all-in
• About Fujitsu : Fujitsu Global
• RICOH Image Scanners - Country Selection for Inquiry | Global | Ricoh
• Support for RICOH fi Series | Global | Ricoh

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>