McGrathLocks FM810T Ml Albion Digital Locks User Guide

October 30, 2023
McGrathLocks

McGrathLocks FM810T Ml Albion Digital Locks User Guide
Digital Locks

Important remarks

  • Please store the mechanical key in an outdoor safe place.
  • Any function changes, please subject to the actual product.
  • The photos in this guide are for reference only.

Download and Install the APP

Enable your smart phone to scan QR code to download the APP. Also you can sear ch7T Lode on APP store or Google play to download the APP.
QR code
Stan to download APP

Setting via lock
If you don’t want to use the APP, you may follow the programming instructions below.

Create New Access
Add administrator (only 1):
Access
a. Enter ’12X
b. Input 123456$ (the initial codel
c. Input admin codes (4.9 digits)
d. Repeat admin codet/

Add a new user with an access code (150 at most):
Access

a. Enter ’85#
b. Input admin codes
c. Input user codelt (4-9 digits)
d. Repeat user codex

Add a new user with art RFID card ( 200 at most):
Access

a. Enter ‘855
b. Input admin odes
c. Swipe the card
Tips: If your sm rtphone supports NEC, copy the registered REID card to your smartphone, the phone will be the key to unlock.

Modify Code
Modify Admin Code
Access
a.
Enter ’12N
b. Input old admin coda
c. Input new admin coda
d. Repeat the new admin coda

Modify User Code
Access

a. Enter •105
b. Input old user coda
c. Input new user coda
d. Repeat the new user coda

Manage the Language
If not reg ster the admin code, the default admin code is 123456

Delete User
Dlete e ALL Access Codes:
Access

a. Enter •71#
b. Input admin oda
Delete ALL RFID Cards:
Access

a. Enter •69#
b. Input admin coda

Reset the Lock
Long press the Reset button, when hear ‘please input initialization passcode’, input 0005, reset successfully. All code/card/phone users will be deleted.

Demo Mode
The demo mode is turned off by default, when not register the admin code, enter 246795 will open the demo mode. During the demo mode, input 1234565 or any cards can unlock. After registering the admin, the demo mode will be invalid automatically.

Low Battery Alert
When the battery’s in low power, the buzzer will warn ‘low battery power’ while each unlocking. The keypad light flashes 1 s . Please change with new Alkaline batteries, don’t mix new and old batteries.

Scrambling Code Anti Peep
Users may enter any random digits before or/and after the correct passcode and can still gain access. make sure strangers can’t steal your passcode by watching you nearby when you enter the passcode.

Always Open Mode
This stops the door from locking and puts it into passage mode. Useful when gardening, bringing groceries in from the car etc.

Unlock icon After a successful unlock performance, press ‘123#’ within 5 seconds, will activate Always open mode. The mode will keep the door unlocked.
Lock icon To deactivate Always Open Mode, just unlock once again via card/code/APP. If you activate the Always Open Mode on APP, you must close it on APP, too.

FAQ

Installation completed, but there is no power

Please check the Positive and Negative of batteries.

Lock won't response and lock keypad can't light up

A. If the lock is just installed and battery inserted Correct, please check whether the cable connection between exterior and interior unit is properly connected to both units. Check the cable for nicks or damages. B. If the lock already used for a while, please check If the battery is dead. You can insert new battery or connect to a power bank to the USB port.

The door won't be locked automatically

A. Please check if the lock is under Always open Mode. B. Please refer to the direction of Letter A and Letter B on the exterior lock spindle holder. Make sure the spindle holder direction is correct.

The battery life is short

A. Please check whether the cable connection between exterior and interior unit is properly connected to both units. Check the cable for nicks or damages. B. Please check whether the Alkaline batteries installed are all new. Don’t mix the old and new batteries. Don’t use the rechargeable battery.

Installation Instruction

Explosion diagram
Installation

A. Lock mortise
B. Exterior assembly
C. Mounting plate
D. Interior assembly

Install the lock mortise
This lock supports two different types of lock mortise as follows. Check what you get in the box and install it on the door. Ensure that the mortise faceplate is flush with the door,according to the mortise position.

  • Strike plate

  • Single latch

Lock mortise

  • Strike plate
    Lock mortise

  • Dual latch mortise
    Lock mortise

Reverse the direction of the lock handle (when needed)

  • Remove the screw C
    Lock Handle instruction

  • Rotate the handle up 180°
    Lock Handle instruction

  • Fasten the screw C
    Lock Handle instruction

Dismantle the mounting plate from the interior lock assembly as below

Mounting
Interior lock assembly Mounting plate (with rubber)

Tighten 2 screw studs on the exterior lock metal plat

Screw installation
Exterior lock assembly

Single latch
If the handle points to left as below, rotate the letter A to point to triangle icon
Single latch

If the handle points to right as below, rotate the letter A to face down.
Single latch

Dual latch mortise

Rotate the letter B to point to triangle icon
Dual latch mortise

Choice of the spindle length= door thickness+18~39mm
Pindle length

Install exterior lock assembly

A. Take the exterior lock assembly and place it on the door, the cable goes under the latch, slide the spindle through the mortise square hole.
B. Put the mounting plate and pass the cable from the middle hole of the plate.
C. Screw the two screws but don’t tighten them yet.
D. Align the mounting plate with the door edge and must make sure there is enough space between the spindle and the round hole on the mounting plate.
E. Place the interior lock assembly, turn the front and rea handles to check both can go smoothly.
F. Remove the interior lock assembly, then tighten the two screws.
Installation

Install interior lock assembly

A. Connect the cable to interior lock assembly.
B. Put and tighten the four screws.
C. Put the silicon cover back to the bottom screws holes.
D. Test the handle and mechanical key.
E. If you have a power bank, please connect to the bottom USB port on the exterior lcok.
F. Put 4pcs AA batteries. Now you can start to config the settings.
Installation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals