ecoer ELG02 Ecolink HVAC Gateway Instruction Manual
- July 17, 2024
- ecoer
Table of Contents
ecoer ELG02 Ecolink HVAC Gateway
Read Before Installing
The ecolink Gateway Provides remote access to ecolink Adapter through the
internet and Ecoer Smart Service (ESS) Pro
Must be installed by a trained, experienced technician. Read these
instructions carefully. Failure to follow these instructions can damage the
Product or cause a hazardous condition.
Specifications
Model : ELG02
Operating Ambient Temperature : -13℉ to 167℉ (-25℃ to 75℃)
Operating Relative Humidity : 5% to 95% (non-condensing)
Power Adapter Rated Input Voltage : 100 VAC ~ 240 VAC @ 50 Hz/60 Hz
Power Adapter Output Voltage Range : 4.80 VDC ~ 5.20 VDC
Max Output Current : 2000mA
Maximum Number of Units : 5 per ecolink Gateway
A “Unit” is:
ecolink Adapter that is wired to the heating/cooling equipment.
ecolink Zone Panel wired by thermostats.
Need help
For more information about this Product please
visit www.ecoer.com
or call +1 703-348-2538 for technical
support.
Download the ESS Pro
INSTALLATION
Step 1
Connect an enthernet cable from the ecolink gateway to an internet-connected
home router.
Step 2
Connect the power cable to the ecolink gateway.
Step 3
Connect the power adapter to a wall socket.
Then the blue led start to light up.
After connecting to the cloud server, the gateway will start flashing the
green led.
Step 4
Power up the ecolink Adapter.
Step 5
Following the ESS Pro App instructions to register the ecolink system by
scaning the QR code.
LED BEHAVIOR
Solid Blue : The Gateway starts to up.
Blinking Blue : The Gateway is connected to Ecoer server and exchanging
data with Adapter.
Blinking Red : Connecting to Internet and logging in Ecoer server.
Solid Red : The Gateway fail to connect to the Ecoer server
Blinking Green : The Gateway is not communicating with the ecolink
system.
ECOLINK GATEWAY CHECKLIST
Power Cable is Connected.
Ethernet Cable is Connected.
ecolink Adapter is power on.
Gateway and Adapter are registered to ESS Pro App.
FCC Compliance Statement Compliance Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation .This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of FCC rules. Operation is subject to
thefollowing two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
Change or modifications that are not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
RF Exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 8 inches during normal operation.
Warning: Changes or modifications not expressly approved by ECOER INC could
void the user’s authority to operate the equipment.
Customer Support
Model: ELG02
Addr.: 43671 Trade Center Place, Suite 100 Dulles, VA 20166
Tel: 703-348-2538
Website: www.ecoer.com