SOLTECH HYBRID 65W LED Solar Area Light Instruction Manual

SOLTECH HYBRID 65W LED Solar Area Light

Specifications

• HYBRID 45W: 43.5 inches
• HYBRID 65W: 46.6 inches
• Dimensions (L x W x H):
  • HYBRID 45W: 19.5 inches x 19.5 inches x 4.4 inches
  • HYBRID 65W: 19.0 inches x 19.0 inches x 5.2 inches

Product Information

SOLTECH Designs and Manufactures Advanced, Solar-Powered LED Technology. HYBRID solar lights are easy to install and virtually maintenance free. They use solar cells to convert sunlight into electricity, which is stored in batteries for use at night. Using these lights won’t increase your electric bill.

Precautions
When working with solar panels, cover the panel with an opaque layer when exposed to sunlight to avoid shock hazards. Do not make contact with the terminals when the panel is exposed to any light source.

Product Usage Instructions

Introduction
Thank you for purchasing HYBRID Urban Lighting Products. Read all instructions carefully before installation. Do not attempt to repair the product on your own as it may cause serious damage and void the warranty.

Battery Notes

1. The LiFePO4-battery-powered Sunlike lights are brighter and more reliable.
2. Charging the battery fully may take up to 6 to 12 hours.
3. The rechargeable battery can work continuously for 10 hours at full power.
4. The controller adjusts light output relative to battery capacity rather than max LED output.

45W 65W Installation Manual

SOLTECH Designs and Manufactures Advanced, Solar-Powered
LED Technology.

Introduction

Thank you for purchasing HYBRID Urban Lighting Products.

Introduction

Outdoor solar lighting systems use solar cells which convert sunlight into electricity. Electricity is stored in batteries for use at night. HYBRID solar lights are easy to install and virtually maintenance free. Using them won’t increase your electric bill.

Important

• In order to avoid deep discharge of the battery during storage, please fully recharge your battery every 4 months. Please make sure that the light is installed in an area with sufficient sunlight irradiance. A strict minimum of 3.5 hours/day of sunshine on average is recommended. Se-lect the right operating mode according to the local legislation needs and the local sunshine conditions. Keep it away from shadows. Self-cleaning available when the light fixture have minimum angle of
  15 degrees.

• Please save these instructions. Read all of the instructions carefully before attempting to carry out any installation or wiring. Do not open or
  attempt to repair the product on your own, as it many cause serious damage and would void the product warranty. Contact your local distributor for any questions concerning the installation.
  Range of the light module on the lighting fixture is 20–26 feet (6–8 meters). The ideal installation spacing is >16 feet(5 meters). When installing two or more lighting fixtures on one pole, select desired operating mode before installation.

• Interference can cause delay or malfunction when using the remote control to change operating modes after installation.
  Precautions when working with solar panels

• When the solar panel is exposed to sunlight, a voltage appears at the output terminals of the solar panel turning it into a source of electricity. To avoid a shock hazard, make sure the solar panel is covered with an opaque (dark) later such as paper or cloth during the installation. Do not make contact with the terminals when the panel is exposed to sunlight or any other light source.

Battery Notes

1. The LiFePO4 -battery-powered Sunlike lights are visibly brighter than other outdoor solar lights, and their performance overall is more reliable.
2. To charge the battery fully may take up 6 to 12 hours.
3. The rechargeable battery can work continuously for 10 hours at full power.
4. The controller makes the light output of a selected percentage on the remote relative to battery capacity rather than max LED output.
5. Battery will stop charging when the ambient temperature is below – 22°F or above 140°F.

(IAP) Intelligent Adaptive Program Battery Control Technology
In order to extend the off-grid autonomy of the HYBRID under shady trees, heavy rain, and thick clouds, our controllers now integrate an adaptive smart control feature to actively track battery capacity and adjust light output accordingly. Before integrating this feature, select-ing a light output percentage on the remote would yield an accurate percentage of max LED brightness. Now with (IAP), the controller actively monitors the battery and regulates the electrical current to the LEDs. The controller makes light output of the selected percentage on the remote relative to battery capacity rather than max LED output. This smart-control feature can increase our off- grid performance by up to 40%.

Battery Status is indicated by the red/green indicator on the lighting fixture as follows:

• Red indicator (Charging)

  • Slow red light flashing = Charging
  • Red light continuously on = fully charged
  • Quick red flashing = charge fault

• Green indicator (Discharging)

  • Green light continuously on = more than 40% of the battery capacity remaining
  • Slow green light flashing = battery capacity below 10%
  • Quick green light flashing = battery below 0% mode—Protect
    battery does not over discharging

• Blue indicator (On-grid Power)

  • Blue light continuously on = Switch to on-grid power

Storage
To avoid over discharge of the battery during storage, please recharge the lighting fixture every 3 months. Use the dedicated charger to charge, reset the switch when done.

MPPT Controller

• Maximum Power Point Tracking (MPPT) is a technique for tracking and regulating the output energy from the solar panel to the battery.
• Measures the solar panel output voltage and current in real-time and continuously tracks the maximum power.
• Regulates the output voltage so that the system can always charge the battery with the maximum power.
• Significantly improves the solar system energy utilization rate, with a conversion efficiency up to 97%.
• Increases the solar system’s charging efficiency by at least 20%compared to Pulse Width Modulation (PWM)

 Installation and Wiring Compliance

1. Installation and wiring must comply with the State and National Electrical Codes.
2. The HYBRID 45W/65W model is intended for outdoor use only and should not be installed in an unventilated area, and shall be installed in an environment within the operational temperatures defined for the product.
3. Before installation, if applicable, please ensure the light pole and its foundation are solid enough to withstand the lighting fixture(s).
4. Before installation, please ensure that the battery is fully charged. Install during sunny days if possible.Before installation, please press the ON/OFF key in the remote control and check whether it shows a red light on the indicator. Please cover the panel and check if the light module turns on normally within 1 minute.

After Installation
The lighting fixture will automatically turn on at night and turn off during daylight.
Important
Always orient the solar panel facing the equator (e.g. facing south if in northern hemisphere).
Always have a tilt angle of at least 15° to avoid dust accumulation (0°=horizontal plane).

Mounting Accessories

 Installation

Slip Fitter

WARNING:
To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a qualified electrician only, following all applicable electrical codes.

To Avoid Electric Shock

• Be certain electrical power is OFF before and during installation and maintenance.
• The luminaire must be connected to a wiring system with an equipment-grounding conductor.

To Avoid Explosion:

• Make sure the supply voltage is the same as the rated luminaire voltage.
• Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.
• Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
• Keep the lens tightly closed when in operation.

Panel Angle

The solar charge in a battery pack won’t last forever. The off–grid system relies on stored solar energy for autonomy. Angling your solar panels properly can boost the power intake of your solar lighting system. You want to angle your solar panels at a tilt based on the area’s latitude.

Tip
You can increase the tilt 15° in the winter or decrease 15° in the summer. In this way you can get the maximum sunlight to recharge the battrey

Detection Zone

Remote Control Guide

The range of the remote control to the indicator is 16ft (Day time) to 33ft (Night time). Because the sunlight will impact the signal of the remote control, we suggest our users to setup the mode before they install the light.

1. On/Off
   When off is selected, the light will stop working. The solar panel will not charge the battery and the battery will not supply electricity to the light.

2. Connect/Test
   Remote control device can be connected with any lighting fixture, one at a time. To connect, press the button once. It also functions as a test button. To test, press the “Test” button once, the red light will indicate the fixture is charging, green light indicates that the fixture is operating. Testing lasts for 10 seconds, and then it goes back to the mode previously in use.

Remote Control Guide

40%~100% Motion Sensor Mode
Constant 40% brightness (turns on at dusk, turns off at dawn); 100% brightness turns on for 2 minutes when motion is detected.

20%~80% Motion Sensor Mode (Default)
Constant 20% brightness (turns on at dusk, turns off at dawn); 80% brightness turns on for 2 minutes when motionis detected.

Night Owl Mode
Changes as natural light decreases/increases (turns on at dusk); 70%brightness for 0.5 hour, 100% brightness for 3.5 hours, 70% bright-ness for 1 hour, 50% brightness for 1 hour, 20% brightness for 5 hours (turns off at Dawn).

Early Bird Mode
Changes as natural light decreases/increases with increased brightness near dawn for early risers (turns on at dusk); 70% brightness for 0.5 hour, 100% brightness for 3.5 hours, 70% brightness for 1 hour, 50%brightness for 1 hour, 20% brightness for 4 hours, 100% brightness for 1 hour (turns off at Dawn).

(IAP) Intelligent Adaptive Program Battery Control Technology
In order to extend the off-grid autonomy of the HYBRID under shady trees, heavy rain, and thick clouds, our controllers now integrate an adaptive smart control feature to actively track battery capacity and adjust light output accordingly. Before integrating this feature, select-ing a light output percentage on the remote would yield an accurate percentage of max LED brightness. Now with (IAP), the controller actively monitors the battery and regulates the electrical current to the LEDs. The controller makes light output of the selected percentage on the remote relative to battery capacity rather than max LED output. This smart-control feature can increase our off- grid performance by up to 40%.

Important
Dusk and dawn time can vary for different locations and seasons. The sensors in our products will monitor the light levels where it is installed. The time period shown in the chart above is just an example to help you understand the different lighting modes.

100% Constant Mode
100% brightness from dusk to dawn.

70% Constant Mode
70% brightness from dusk to dawn.

40% Constant Mode
40% brightness from dusk to dawn.

Timer Mode Disabled
Press this button to turn off Timer Mode; settings revert back to before Timer Mode was last activated.

Timer Mode 4 Hours
This is an additional mode which can work with any other modes. For example: press this button at any time after you turn on 70%Constant Mode. If the light turns on at 7pm at dusk, it will turn off at 11pm. It will repeat the same schedule hereafter until it is canceled by pressing Timer Mode Disabled.

Time Mode 8 Hours
This is an additional mode which can work with any other modes. For example: press this button at any time after you turn on 70%Con- stant Mode. If the light turns on at 7pm at dusk, it will turn off at 3am. It will repeat the same schedule hereafter until it is canceled by pressing Timer Mode Disabled.

HYBRID products are covered by a 5 year limited warranty. SOLTECH urban light warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 5 years from date of purchase. To obtain warranty service please contact your local distributor or sales rep for further instruction.

SOLTECH LLC reserves the right to update all product data sheets at any time. Consult SOLTECH marketing specialists for publication updates at hello@soltechlighting.com
Copyright©2018–2024 SOLTECH LLC,
All Rights Reserved.
I soltechlighting.com I hello@soltechlighting.com I 510-891-1056 I 1460 Park Avenue, Emeryville, CA 94608 I

SOLTECH Designs and Manufactures Advanced,
Solar-Powered LED Technology.

References

• Commercial Solar LED Lights | SOLTECH Smart Solar Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>