Projectors HJ-XKD09 Galaxy Light Projector for Bedroom User Manual
- June 6, 2024
- Projectors
Table of Contents
Projectors HJ-XKD09 Galaxy Light Projector for Bedroom User Manual
Unpacking inspection:
Thank you for purchasing our product. Please read this manual before using the
product. This manual contains necessary safety recommendations and user
instructions. Please follow the instructions in this manual to avoid damage
arising from misoperation. Please check the received product for damage!
Warning:
This product is applicable to the USB DC 5V/2A power supply. In case of
noncompliance, please use a regulator; otherwise, the service life of this
product may be affected.
Accessories
-
Polar star light X1
-
Remote control X1
-
Data cable X1
-
Manual X1
Buttons
- ON/OFF button
- The LED and laser are ON by default after this product is turned on. Press this button to disable the laser.Press it again to enable the laser and disable the LED, and press it once more to enable the laser and LED at the same time.
- Press it to select the previous option, and press and hold it to decrease the volume.
- Press it to select the next option, and press and hold it to increase the volume.
Buttons of remote control
1| |
Power ON/OFF
---|---|---
2| |
Polar light ON/OFF
3| | Laser ON/OFF
4| |
Volume +/-
5| | Previous/Next
6| |
Music Pause
7| | LED red light|
Press it once to enable a color and again to disable the color. At most three
colors can be
enabled at the same time. When the fourth color is enabled, the color that is
enabled first will be disabled, while other colors remain unchanged.
8| |
LED green light
9| | LED blue light
10| |
LED white light
11| | Brightness +/-
(darkest, darkest, bright, fully bright)
12| |
Polar light speed +/- (motor speed)
13| | Timing – 1/2 hour
(flashing light and prompt sound)
14| |
Three modes have been preset. Press it once to enable a mode.
15| | Voice-activated mode (available in Bluetooth mode)
16| |
Switching of Bluetooth mode and built-in music mode
Use the remote control correctly and make sure it points at the infrared sensor.
Laser parameter
Single-point laser power: less than 1MW
LED light source: 1*4W| Power consumption: 7-10W
Power input: 100-240V AC 50-60HZ USB DC5V / 2000mA
Working temperature: 4°F – 113°F (-20°C – 45°C)
Projection area: 215-861 square feet (20-80 m2)
(Laser is harmful to eyes. Do not look at it directly.)
Statement:
- This product has been tested comprehensively and strictly before delivery.
- Users should follow the warnings and instructions. Incorrect use will cause product damage, which is excluded from the company’s warranty.
- Strictly follow the operating instruction.
- Do not dismantle the host and accessories.
- This product has a function of automatic shutdown after 4-hour operation.
- It can work continuously for 4 hours and automatically shut down.
- When the product is continuously powered on, the previous settings will be kept in the memory and maintained after restart.
- If the power supply is disconnected, default settings will be restored (except for timing; this product will shut down after 4-houroperation by default after each startup).
Bluetooth connection
Press “Bluetooth” on the light body or remote control. There will be a prompt
“Bluetooth mode”. Enable the mobile Bluetooth.
Find HJ-09 , and select and connect it. After successful connection, there
will be a prompt “connect”.
Note:
This product is suitable for indoor use and subject to Class IP20 protection.
It should be used in dry places and not in humid, overheated or dusty placed.
Use an adapter that meets the requirements of this product. The maximum and
minimum ambient temperatures for normal and stable operation of the light are
40 and -20 , respectively.
Use a power adapter that is greater than 5V and 2A. Otherwise, if the
current is too low, the light will not work normally.
Prevent this product from falling. Otherwise, the laser module may be
damaged, resulting in laser failure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>