Posey 2814, 2819 Double Security Mitts Instruction Manual
- July 15, 2024
- Posey
Table of Contents
- Posey 2814, 2819 Double Security Mitts
- DESCRIPTION OF PRODUCT :
- INTENDED USE:
- PRECAUTIONS:
- POSEY DOUBLE SECURITY MITTS:
- ADDITIONAL SAFETY AND LAUNDERING INSTRUCTIONS ON OTHER SIDE.
- LAUNDERING INSTRUCTIONS (if applicable):
- HOW TO TIE THE POSEY QUICK-RELEASE TIE
- Specifications:
- FAQ:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Posey 2814, 2819 Double Security Mitts
INSTRUCTION MANUAL
DESCRIPTION OF PRODUCT :
Padded mitt without finger separators with connecting strap.
INTENDED USE:
- To protect patients assessed to be at risk of disrupting life-saving treatments (e.g., chronic tube pulling) or in danger of injury to themselves or to others by limiting hand movement.
- Limits limb movement if used with connecting strap
- Follow your hospital’s restraint policies and procedures that are compliant with USA CMS guidelines and state laws, or other governing agencies outside the USA.
CONTRAINDICATIONS: None
APPLICATION INSTRUCTIONS: (Repeat steps 1- 4 for each mitt):
NOTE: Product is designed for use with connecting strap (item 2809) (visit tidiproducts.com).
1. Insert the patient’s hand into the mitt, palm down.
2. Wrap the wrist strap around the smallest part of the patient’s wrist, over
the top of the wrist, through the plastic ring, and secure it onto itself.
3. Bring the second hook strap over the top of the loop strap to form a
“double security” closure.
4. Slide ONE finger (flat) between the mitt and the inside of the patient’s
wrist to ensure proper fit. The strap must be snug, but not compromise
circulation.
NOTE: Follow steps 5-6 for use of optional mitt connecting strap (hospital bed use only) to help prevent the patient from removing the device or inflicting self-injury:
5. Wrap the strap around the patient’s wrist or pass it through the loops on
the mitt.
6. Use Posey quick-release tie (see drawings on reverse) to secure the end of
the strap along the frame that moves with the patient out of patient’s reach
(do not attach to side rail or head/footboard). Tie strap at a point midway
between the patient’s wrist and elbow, out of the patient’s reach.
PRECAUTIONS:
• A clinical assessment and decision are required when used with monitoring
lines or if patient has a wound or dislocated/fractured limb.
• Ensure that mitts are properly secured. If applied too tightly, circulation
will be restricted; if applied too loosely, the patient may be able to slip
his or her limb from the device.
CAUTION: RX Requirements.
Certain types of hand mitts can be considered a restraint. Pinning or otherwise attaching those same mitts to bedding or using a wrist restraint in conjunction with the hand mitts would meet the definition of restraint and the RX requirements would apply. Refer to USA CMS Interpretive Guidelines 482.13(e).
POSEY DOUBLE SECURITY MITTS:
2814: Mesh Mitt, Single Padded with Anchor Strap
2819: Cloth Mitt, Double Padded with Anchor Strap
2809: Connecting Strap
WARNING: Additional or different body or limb restraints may be needed (visit tidiproducts.com):
-
Some patients may require additional interventions in conjunction with this device in order to prevent injury to self or others.
– To reduce the risk of the patient getting access to the line/wound/tube site. -
It is a clinical decision to decide when a restraint is no longer deemed safe.
BED SAFETY: Refer to the Food and Drug Administration (FDA) , or other governing agencies outside the USA, for the most recent Hospital Bed Safety Guidelines and the bed manufacturer’s instructions for use.
Report any serious incident related to device use to TIDI Products and the Member State Competent Authority. | Translations of this document in French, Spanish, Dutch, German, Italian, and Portuguese are located at www.tidiproducts.com/IFU.
ADDITIONAL SAFETY AND LAUNDERING INSTRUCTIONS ON OTHER SIDE.
For RX PRODUCTS ONLY. Federal law (USA) restricts RX devices to sale by or on order of a physician. For use in a licensed healthcare facility only.
STAFF TRAINING: TIDI offers in-service training aids at no charge. Contact TIDI online at www.tidiproducts.com or call toll-free at 1.800.521.1314.
BEFORE APPLYING ANY RESTRAINT: Follow your hospital’s restraint policies and procedures that are compliant with USA CMS guidelines and state laws or other governing agencies outside the USA.
ADDITIONAL WARNINGS:
1. ALWAYS monitor patient per facility policy. Improper application or use of any restraint may result in serious injury or death. Be aware that constant monitoring may be required for:
- Aggressive or agitated patients; and
- Patients in a supine position; ensure that being in this position would not cause any complications for those who are at risk of vomiting while being restrained.
2. NEVER alter or repair this product. ALWAYS Inspect before each use: Check
for broken stitches or parts; torn, cut or frayed material; or locks, buckles,
or hook-and-loop fasteners that do not hold securely. DO NOT use soiled or
damaged products. Doing so may result in serious injury or death. Dispose of
damaged products per facility policy for BIOHAZARDOUS material.
3. ALWAYS secure straps to a part of the frame that moves with the patient
(not foot/head board or siderails), out of the patients reach, using
quickrelease ties (see drawing below) or buckles. These allow easy release in
the event of an accident or fire.
Test to make sure straps cannot tighten, loosen, or slip and create excess
slack. If this occurs, the patient may slide off the chair or bed, increasing
the risk of serious injury or suffocation. Restraint release is an important
part of facility fire and disaster drills. Straps can be cut with scissors in
an emergency.
4. NEVER secure restraint strap to side rail or head/foot board.
5. NEVER use Posey products on toilets, or on any chair or furniture that
does not allow proper application as directed in the Application Instructions.
DO NOT use at home.
6. NEVER expose this product to open flame, fire, smoking materials, or high
heat sources. Some products may melt or ignite and burn. The facility
smoking/no smoking policy should be strictly enforced.
7. NEVER use a Posey product as a seat belt in a moving vehicle. Posey
products are not designed to withstand the force of a crash or sudden stop.
8. Test Zippers or hook-and-loop fasteners before each use. DISCARD device if
it does not fasten securely.
LAUNDERING INSTRUCTIONS (if applicable):
- Fasten all buckles and locks to reduce risk of damage during wash and dry cycles. DO NOT put buckles or locks through extractors. For maximum life, launder in a laundry bag.
- Stainless Steel Locks: Posey recommends that locks be treated with a dryfilm lubricant (silicone) after each cleaning. For best results, spray a small amount into the lock. Work the action of the lock with a key several times to ensure that all the surfaces are well lubricated.
- Before laundering, zip up and turn the product inside out to protect zipper.
- Hook-and-loop fasteners may collect lint after repeated use or laundering, reducing grip strength. Fasten the “hook” to the “loop” before laundering to help prevent lint buildup. As needed, use a stiff-bristle brush to remove lint from the “hook” side.
These products, other than foam products, can be machine washed under CDC guidelines for material soiled with blood or bodily fluid.
- For non-contaminated material, use lower temperature wash and dry cycles to extend product life.
For foam products:
- Make sure products are completely dry before use.
STORAGE AND HANDLING:
- This device is designed for use in normal indoor environments.
- This device may be stored in ambient warehouse temperatures at normal humidity levels. Avoid excess moisture or high humidity that may damage product materials.
HOW TO TIE THE POSEY QUICK-RELEASE TIE
1. Wrap strap once around the frame that moves with the patient (do not
attach to side rail or head/footboard), leaving at least an 8” (20 cm) tail.
Fold the loose end in half to create a loop and cross it over the other end.
2. Insert the folded strap where the straps cross over each other, as if
tying a shoelace. Pull on the loop to tighten.
3. Fold the loose end in half to create a second loop.
4. Insert the second loop into the first loop.
5. Pull on the loop to tighten. Test to make sure strap is secure and will
not slide in any direction.
6. Repeat on other side. Practice quick-release ties to ensure the knot
releases with one pull on the loose end of the strap.
Specifications:
- Product Name: Posey Double Security Mitts
- Models Available: 2814 Mesh Mitt, 2819 Cloth Mitt, 2809 Connecting Strap
- Design: Padded mitt without finger separators with connecting strap
- Usage: Designed for patient safety and prevention of self-injury
© 2023 TIDI Products, LLC. Todos os direitos reservados.
Posey é uma marca comercial registada da TIDI Products, LLC.
UK Pessoa responsável
Emergo Consulting (UK) Limited
c/o Cr360 – UL International
Compass House, Vision Park Histon
Cambridge CB249BZ
Reino Unido
FAQ:
Q: Are there any contraindications for using these mitts?
A: No, there are no contraindications mentioned for the product.
Q: Where can I find additional safety and laundering instructions?
A: Additional safety and laundering instructions are provided on the other side of the product documentation. You can also visit tidiproducts.com for more information.
References
- Medical Products for Staff & Patient Safety | TIDI Products
- Medical Products for Staff & Patient Safety | TIDI Products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>