SALTO IQ 3.0 BLUEnet Wireless Gateway Installation Guide

SALTO IQ 3.0 BLUEnet Wireless Gateway

Product Specifications

• Device Type: Gateway
• Connectivity: Ethernet, WIFI, Bluetooth, RS-485
• Weight: 225g
• Dimensions: 122.5mm x 42mm

Product Usage Instructions

Installation Guide
The IQ3 device serves as a Gateway for communication between Nebula and SALTO BLUEnet devices, enabling SVN features.

Installation Options
Ceiling/Wall Installation: Follow the provided diagram for hidden cable installation.
Desktop Installation: Refer to the diagram for desktop mounting instructions.

Connection Options
Ethernet + WIFI Model: Plug in the device to establish connectivity.
ETHERNET + POE Model: Connect the device using Ethernet and Power over Ethernet.
ETHERNET Model: Simply plug in the Ethernet cable for connection.

Communication Wiring
Follow the provided wiring diagram to connect the device to SALTO Node for communication.

External Power Supply
The device requires an external power supply except for PoE models.

Frequently Asked Questions (FAQ)

1. Q: What are the main connectivity options of the IQ3 device?
   A: The IQ3 device offers connectivity through Ethernet, WIFI, Bluetooth, and RS-485 interfaces.

2. Q: Does the IQ3 device support Power over Ethernet (PoE)?
   A: Yes, some models of the IQ3 device support Power over Ethernet (PoE) for power supply.

The IQ3 is a Gateway device that ensures the communication between Nebula and the SALTO BLUEnet devices providing the SVN (SALTO Virtual Network) features.
It is equipped with an Ethernet, WIFI (), Bluetooth and RS-485 interface.
() Depending on the model.

Installation

CEILING/WALL INSTALLATION WITH HIDDEN CABLE

CEILING/WALL INSTALLATION WITH EXPOSED CABLE

DESKTOP INSTALLATION

SEE  WIRING DIAGRAM

Wiring

ETHERNET MODEL

ETHERNET + POE MODE

ETHERNET + WIFI MODEL

( * )Not included

ETHERNET MODEL

ETHERNET + POE MODEL

If there is no PoE infrastructure, use auxiliary power supply.

ETHERNET + WIFI MODEL

If you do not connect to a WIFI network, connect the Ethernet cable.

COMMUNICATION WIRING DIAGRAM IN IQ3/SALTO Node

RS485 CONNECTION TO TERMINAL.

RS485 bus termination resistor is needed (ON position) when the node is located at the end of the bus.

1. Power (except PoE).
2. Ethernet.
3. RS485 (Jack cable).
4. RS485.

Electrical Features

EXTERNAL POWER SUPPLY CHARACTERISTICS

| Min| Max| Typ
Input Voltage| 12-5%V| 12+5%V| 12V
Max Input Power| 15w| |
**Current Consumption***| | 200mA| 60mA

• Excluding RS485 Nodes.
  Power supply must be calculated taking into account SALTO Nodes current consumption.

CABLE REQUIREMENTS

Ethernet ** UTP CAT5e
Node Connection| By means of Terminal Blocks: Generic twisted pair
By means of RJ45: UTPCAT5e
OPERATING CONDITIONS**

| Min| Max
Temperature| 0ºC| 60ºC
Humidity| 0| 95% (Non condensing)
SALTO BLUEnet CHARACTERISTICS

Frequency Range| 2400 MHz to 2483.5 MHz
Standard| Bluetooth 5.2 Compliant
TX power| 8dBm
Indoor Range| 10 – 15m *
WIFI CHARACTERISTICS

Frequency Range| 2400 MHz to 2483.5 MHz
Standard| IEEE 802.11b/g/n compliant
TX power| 16dBm
Range| 25 – 30m *

• Depending upon installed environment. To ensure correct operation, do not install the device near a metallic surface.

MAX. NUMBER OF DEVICES TO BE CONNECTED

SALTO Nodes                                6
Access points                              112
PoE

PoE Norms: IEEE 802.3af / IEEE 802.3at
PoE Class                            0

• The environment has a direct impact on the BLUEnet range radiation (metal, concrete walls…)
  The receiver device must be located facing the product antenna. Please check your product’s BLUEnet antenna position. Recommended connectivity distance: 10m – 15m

Configuration

1. The device is configured using the Nebula App.
2. Ethernet test: without any type of set up, the IQ3 is a DHCP ready device. If your network supports it, it is possible to check the Ethernet connectivity by pinging the address SALTO-IQ3-XXXXXX(XXXXXX corresponds to the final 6 digits of MAC).

Installation example

Maximum number of SALTO Nodes: 6
Maximum number of access points: 112

Signals

Operational test

1. Check that the red light turns on.
2. If you have connected to Ethernet, check that the lights on the RJ45 turn on.

All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any item in this catalog, its design, construction, and/or materials.
© 2023 SALTO Systems S.L.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>