Rayrun TT40 Smart and Remote Control RGB+W LED Controller User Manual

Rayrun TT40 Smart and Remote Control RGB+W LED Controller

FUNCTION

Introduction

TT40 LED controller is designed to drive constant voltage RGB+White color LED products in voltage range of DC12-24V. It can be controlled by smart phone with Tuya smart app connection or by the stand alone RF remote controller. User can setup LED brightness, color, scene and dynamic effects with the rich function on smart phone Tuya app or the easy operation remote controller.

Terminal & Size

Power supply input
Connect positive power to the cable marked with ‘+’and negative to the cable marked with ‘-’. The controller can accept DC power from 12V to 24V, the output is PWM driving signal with same voltage level as the power supply, so please make sure the LED rated voltage is same as the power supply.

LED output
Connect to constant voltage type LED load. Connect the LED to black cable, and R, G, B, W cable to the relevant color Please make sure the LED rated voltage is same as the power supply and the maximum load current is below the controller rated current.
CAUTION! The controller will be permanently damaged if output cables short circuited. Please ensure the cables are well insulated to each other.

Work status indicator (optional)
This indicator shows all working status of the controller. It displays different events as following:

• Steady on: Remote and Tuya smart mode.
• Flash twice: Tuya not connected.
• Flash 3 times: Over heat protection.
• Blink: New command received.
• Long single blink: Brightness or speed reach limit.

Wiring diagram

Functions

• Turn ON / OFF
  Press ‘I’ key to turn on unit or press ‘O’ key to turn off. The power on status can be set to last status or default status from app. At last status mode, the controller will memorize the on/off status and will restore to the previous status on next power on.

• Light mode switch
  Press this key to switch between RGB, white and
  RGB+White mode. In RGB mode, white channel will be disabled; In white mode, RGB channel will be disabled; In RGB+White mode, all channels are usable.

• Select static RGB color
  Press key to select color from the preset library colors.

• Shortcut color select
  Shortcut key to static colors. LED will run the relevant color when pressing the specific color key. The shortcut color is included in content.

• White brightness control
  Press   key to increase white LED brightness and press key to decrease.

• RGB brightness control
  Press key to increase RGB LED brightness and press key to decrease.

• RGB dynamic effect
  Control the RGB dynamic effects. Press to select dynamic effects and press key to set the running speed of the dynamic effects.

• Remote indicator
  This indicator blinks when remote controller working. Please check the remote battery if the indicator does not light up or flash slowly. The battery type is CR2032.

Operation

• Using the remote controller
  Please pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.

• Setup Tuya connection
  Please install the Tuya app to setup the connection.
  Before setup, please make sure the controller is at factory default mode and not connected to any gateway or router.

• Pair a new remote controller
  The remote controller and receiver is 1 to 1 paired as factory default. It’s possible to pair maximum 5 remote controllers to one receiver and each remote controller can be paired to any receivers
  To pair a new remote controller, please follow two steps:

  • Plug off the power of the controller and plug in again after more than 5 seconds.
  • Within 10 seconds after controller powered on, press key simultaneously for about 3 seconds.
    After this operation, the LED lights will flash 3 times to acknowledge that remote pairing is accomplished.

• Reset to factory default
  To reset the controller’s Tuya setting and unpair all remote controllers, please operate with following tw steps:

  • Plug off the power of controller and plug in again after more than 5 seconds.
  • Press key simultaneously for about 3 seconds, within 10 seconds after the receiver powered on.
    After this operation, the controller will be reset to factory default, the Tuya configuration and remote pairing will all be reset

Overheat Protection

The controller has overheat protection feature and it can protect itself from damage caused by some abnormal usage such as overloading which generates excess heat. At overheat situation, the controller will shutdown the output for a short while and recover when temperature drops to a safe range. Please check the output current and make sure it’s under rated level at this situation.

Specification

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>