IDea FCS Series Ceiling Speakers User Manual
- July 4, 2024
- iDea
Table of Contents
IDea FCS Series Ceiling Speakers
FAQ
- Q: What are the different variants available in the FCS Series?
- A: The FCS Series offers three different solutions: FCS4T, FCS5T, and FCS6T, each catering to different power and size requirements.
- Q: Can I install the speakers in outdoor locations?
- A: It is recommended to avoid exposing the speakers to rain or moisture to prevent electric shock risks.
Overview
FCS Series offers a compact solution for applications that require placing professional equipment on ceilings with no complications, due to its easy installation. FCS Series features three different solutions: FCS4T, FCS5T and FCS6T, allowing for a wide range of ceiling applications. With low frequencies starting from 145 Hz, and RMS Powers from 40 to 80W, FCS Series offers solutions for every need when it comes to applications for retail and shopping centers, as well as public indoor spaces and lobbies. FCS Series is designed with both installation and performance in mind. Its compact size and light weight, even in the larger version, allow for easy transportation and placing. Materials like iron, and silk or titanium for speaker domes, contribute to a steady performance during long background music cues, as well as good sound quality for PA.
Warnings
The information furnished in this manual does not include all of the details of design and engineering of this particular product not does it cover every possible application or situation concerning its usage,which may occur during the installation,operation or maintenance of product.
IMPORTANT: THE PRODCUT REQUIRES CLASS 2 OUTPUT WIRING
CAUTION: SHOCK HAZARD – DO NOT ENTER
- TO PREVENT ELECTRIC SHOCK,DO NOT REMOVE TOP OR
- BOTTOM COVERS. NO USER SERVICIEABLE PARTS INSIDE.
- REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
- DISCONNECT POWER CORD BEFORE REMOVING REAR PANEL COVER TO ACCESS GAIN SWITCH.
WARNING
- TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE!
MAGNETIC FIELD
CAUTION: Do not locate sensitive high-gain equipment such as preamplifiers or tape decks directly above or below this unit.Because this amplifier has a high power density, it has a strong magnetic field which can induce hum into unshielded devices that are located nearby. This field is strongest just above and below the unit. If an equipment rack is used, we recommend locating the amplifier(s) at the bottom of the rack and preamplifier or other sensitive equipment at the top.
The lightning bolt triangle is used alert the user to the risk of electric
shock
The exclamation point triangle is used to alert the user to important
operationg and /or maintenance instructions.
Technical Data And Drawings
Technical Data | Fcs4t
| Tweeter | 0.5” (13 mm) Silk soft dome |
|---|---|
| Woofer | 4” (100 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 98 Hz – 20 kHz |
| Power Handling RMS | 40 W program, 20 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:80° – V:70° |
| Crossover Frequency | 4 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 20 W, 10 W, 5 W, 2.5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H × Diameter) | 167.5 × 204.2 mm |
| Weight | 2.3 kg |
| Cut out diameter | 175 mm |
| Material | ABS + iron |
Technical Drawings | Fcs4t
Technical Data | Fcs5t
| Tweeter | 0.75” (20 mm) Titanium dome |
|---|---|
| Woofer | 5” (125 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 85 Hz – 20 kHz |
| Power Handling RMS | 60 W program, 30 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:40° – V:30° |
| Crossover Frequency | 2.8 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 30 W, 15 W, 7.5 W, 3.25 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H × Diameter) | 234.5 × 238.5 mm |
| Weight | 3.3 kg |
| Cut out diameter | 206 mm |
| Material | ABS + iron |
Technical Drawings | Fcs5t
Technical Data | Fcs6t
| Tweeter | 1” (25 mm) Titanium dome |
|---|---|
| Woofer | 6.25” (165 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 65 Hz – 20 kHz |
| Power Handling RMS | 80 W program, 40 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 86 dB |
| Coverage | H:55° – V:45° |
| Crossover Frequency | 3.5 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 40 W, 20 W, 10 W, 5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H × Diameter) | 238.8 × 264.8 mm |
| Weight | 3.7 kg |
| Cut out diameter | 226 mm |
| Material | ABS + iron |
Technical Drawings | Fcs6t
Installation
- STEP 1: Using a stud finder (available at low cost at most hardware stores) or other accurate method, locate center point between two joists and mark. Using template provided, trace hole pattern on surface of ceiling.
- STEP 2: Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in ceiling. Following trace pattern.
- STEP 3: Run loudspeaker wire to sound source location.There are serveral methods you can use to accomplish wiring, depending on the construction characteristics of the room or house.You can add a professional touch to your installation by using a speaker terminal plate at the source location. Leave sufficient amount of wire at speaker location (8-10 inches / 20-25 cm) to complete connection.
- STEP 4: Attach loud speaker wires to speaker terminals, observing correct polarity and position speaker frame up into cutout. Be careful not pinch wires in the process.
- STEP 5: Carefully tighten the four mounting screws. This will cause the mounting wings to rotate our behind the mounting surface and secure the speaker in place.
- STEP 6: After the speaker panel is secured tightly, test sound. When you are satisfied the speaker is operational, then affix grill. As grill is designed for a snug fit you’ll need to position one edge into slot first and press or squeeze around perimeter of grill, while pushing leading edges into grill slot.
NECESSARY TOOLS
- Hammer
- Cross-headed screwdriver
- Paint brush
- Keywhole saw
- Tape measure
- Pencil
Service
This unit has very sophisticated circuitry and should only be serviced by a fully trained technician. This is why each unit bears the following label:
CAUTION
- To prevent electric shock,do not remove covers. No user serviceable parts inside. Refer servicing to qualified technician.
Worldwide service
- Service may be obtained from your local authorized service center.To obtain service, simply present your sales receipt as proof of purchase along with the defective unit to an authorized service center.They will handle the necessary paperwork and repair.Remember to transport your unit in the original factory packaging.
- When sending a product to authorized service center for service, be sure to fill out the service information form and include it inside your unit’s shipping pack. Do not send the service information form separately.
- To ensure the safe transportation of your unit to the authorized service center, ship it in an original factory-packing container.
- Do not ship the unit in any kind of rack. Ignoring this warning may result in extensive damage to the unit and the equipment rack.Accessories are not needed. Do not send the instruction manual, cables and any other hardware.
WEEE Mark
If you want to dispose of this product, do not mix with general household waste.There are separate collection systems for used electronic products in accordance with legislation under the WEEE Directive (Directive 2002/96/EC) effective only within the European Union.
Safety Guidelines
Warnings On Safety Guidelines
- Read this document thoroughly, follow all safety warnings and keep it for future reference.
- The exclamation mark inside a triangle indicates that whatever repairing and component replacement operations must be done by qualified and authorized personnel.
- No user-serviceable parts inside.
- Only use accessories tested and approved by IDEA and supplied by the manufacturer or an authorized dealer.
- Installations, rigging and suspension operations must be done by qualified personnel.
- Only use accessories specified by IDEA, complying with maximum loads specifications and following local safety regulations.
- Read the specifications and connection instructions before proceeding to connect the system and use only cabling supplied or recommended by IDEA. Connection of the system should be done by qualified personnel.
- Professional sound reinforcement systems can deliver high SPL levels that may result in hearing damage. Do not stand close to the system while in use.
- Loudspeakers produce magnetic field even while they are not in use or even when disconnected. Do not place or expose loudspeakers to any device that is sensitive to magnetic fields such as television monitors or data storage magnetic material.
- Disconnect the equipment during lightning storms and when it is not to be used for a long time.
- Do not expose this device to rain or moisture.
- Do not place any objects containing liquids, such as bottles or glasses, on the top of the unit. Do not splash liquids on the unit.
- Clean with a wet cloth. Do not use solvent-based cleaners.
- Regularly check the loudspeaker housings and accessories for visible signs of wear and tear, and replace them when necessary.
- Refer all servicing to qualified service personnel.
- This symbol on the product indicates that this product should not be treated as household waste. Follow local regulation for recycling of electronic devices.
- IDEA declines any responsibility from misuse that may result in malfunction or damage of the equipment.
Warranty
- All IDEA products are guaranteed against any manufacturing defect for a period of 5 years from date of purchase for acoustical parts and 2 years from date of purchase for electronic devices.
- The guarantee excludes damage from incorrect use of the product.
- Any guarantee repair, replacement and servicing must be exclusively done by the factory or any of authorized service centres.
- Do not open or intend to repair the product; otherwise servicing and replacement will not be applicable for guarantee repair.
- Return the damaged unit, at shipper’s risk and freight prepaid, to the nearest service centre with a copy of the purchase invoice in order to claim guaranteed service or replacement.
Declaration Of Conformity
I MAS D Electroacústica S.L. , Pol. A Trabe 19-20 15350 CEDEIRA (Galicia – Spain), declares that FCS4T, FCS5T and FCS6T comply with the following EU Directives:
- RoHS (2002/95/CE) Restriction of Hazardous Substances
- LVD (2006/95/CE) Low Voltage Directive
- EMC (2004/108/CE) Electro-Magnetic Compatibility
- WEEE (2002/96/CE) Waste of Electric and Electronic Equipment
- EN 60065: 2002 Audio, video and similar electronic apparatus. Safety requirements.
- EN 55103-1: 1996 Electromagnetic compatibility: Emission
- EN 55103-2: 1996 Electromagnetic compatibility: Immunity
Contact
I MÁS D ELECTROACÚSTICA S.L.
- Pol. A Trabe 19-20, 15350 – Cedeira, A Coruña (Spain)
- Tel. +34 881 545 135
- www.ideaproaudio.com
- info@ideaproaudio.com
Specifications and product appearance may be subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>