RETRO MANTIS Wireless Gamepad Instruction Manual

MANTIS Wireless Gamepad
Quick Start
Instruction Manual

MANTIS Wireless Gamepad

HOW TO PAIR
PS4: Press Home button for 2 seconds (lights flash BLUE to indicate pairing mode)
First time pairing on PS4? Please use USB-C to connect to system before pairing.
ANDROID : Press “O”+”HOME” button for 2 seconds (lights flash GREEN to indicate pairing mode)
XBOX (PC Bluetooth): Press “Square” + “Home” button for 2 seconds (lights flash RED to indicate pairing mode)
NOTE : Only PS4 mode supports motion sensor, speaker & touchpad capabilities ing butt Enter programming mode by pressing the top right small button + P button on back simultaneously, LED light turns purple and will start to flash,
motors will rumble one time, meaning the device has entered program mode, Press any button you would like to set to be P1 or P2. You can set up to 42 combinations per button at one time, More than 42 times the mode will exist.
Press P again to finish program process and motors will rumble one time to exit program mode. Lights will turn back to normal when you exit program mode.

xinput to dinput mode
On PC, Mantis defaults to Xinput. To change, use back swapping button.
LED indicator
Low power: White light will flash slowly.
No power / need to charge: Gamepad will shut off automatically.
During charging: White light will keep flashing when charging and willl stay lit when charged fully.
gamepad reset
Press the top left button to reset-your gamepad.
reconnect
When gamepad is in OFF status, press the PS Home buttoh for5 seconds.
Gamepad will reconnect to last device.
power off
Hold down “Home” button for 5 seconds to power off,
itis better to add statment how to clear P1/P2 programme button first step is the same to enter programming mode; the second step Is to press P Instead of the button you would like to set to clear P programmable button it is better to add (power off) between “reset” and “Your” as we will do silpri g one “power off’ icon and “P” button.
do you think it is also better to add sensor calibration statment?

Wired mode
On PS4, gamepad recognizes as PS4 mode.
On PC, gamepad defaults to Xinput mode (red lights). Change switch on back of controller to switch to Dinput (green lights). When swapping modes, the motors will rumble one time.
joystick calibrati
(Not needed normally, only if there is an issue with sticks, use to recalibrate)
Gamepad in OFF status, Press X*SHARE+HOME buttons for 3 seconds until RED RGB light turns on to indicate calibration mode.
Rotate left and right stick joystick 3 times each with uniform speed and press three times left and right triggers.
Press OPTIONS to exit joystick calibration mode, then gamepad will turn off

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>