POWERTECH MB3764 12V 850A Jump Starter and Powerbank with 10W Wireless QI Charger Instruction Manual

POWERTECH MB3764 12V 850A Jump Starter and Powerbank with 10W Wireless QI

Charger

WARNINGS & SAFETY INFORMATION

WARNING: The manufacturer is not responsible for any potential injury from misuse

• After starting your vehicle, remove the Jump Starter as soon as possible
• DO NOT connect the 2 alligator clips.
• DO NOT disassemble the Jump Starter
• Do not use the product in the bathroom or other damp places or places near the water.
• Do not remodel or dismantle the device.
• Keep the product away from the children.
• Do not reverse the connections of output or input.
• Do not throw the product into fire.
• Please don’t use a charger whose charging voltage is more than the product to charge.
• The temperature should be kept between 0°C to 40°C when the device is being charged.
• Do not hit or throw the product.
• If there is a problem with charging, please contact your dealer.
• Keep the product away from the flammable objects (Bed or carpet)
• If the liquid of the device is splashed into the eyes, do not wipe the eyes but wash them with clean water immediately.
• If the product is heating and discoloring, please stop using it, as it may lead to liquid, smoke, and burn.
• After long-term storage or not in use, please ensure that devices will be charged and discharged in every three months.

BEFORE FIRST USE

Prior to using your product, please read all the safety and operating instructions thoroughly. Please ensure you follow the steps below before using the product. We recommend you keep the original packaging for storing the product when not in use. Please pay close attention to the section entitled Warnings & Safety Information. Find a safe and convenient place to keep this instruction manual for future reference. Unpack the product but keep all packaging materials until you have made sure your new product is undamaged and in good working order. Ensure you have all accessories listed in this manual.

BOX CONTENTS

• 1 x Jump Starter and Power Bank
• 1 x Battery Clamp

PRODUCT DIAGRAM

OPERATION DETAILS

1. Plug the cable connector into the car jump starter
   • Red Light On
   • The voltage of the jump starter cannot support to start
   • Check the voltage of the Jump Starter
   • Red and Green Light Flash
   • Please check the voltage of the jump starter belonging to 12V/16V
   • Go to Step (2)
2. Connect the jump starter to the car battery
   • Red Light on and Buzzer
   • Short Circuit
   • Disconnect the jump starter and car battery, and go back to step 1.
   • Red Light on and Buzzer
   • Reverse Polarity
   • Disconnect the jump starter and car battery, and go back to step 1.
   • Red and Green lights flash within 1-35 and then the Green Light on
   • Working Status
   • Turn on the Key
3. Green Light On
   • Red Light Flashes
   • Cannot start within 30S
   • If you need to repeat use, disconnect and reconnect the connector

CLAMP PERFORMANCE

voltage of the Jump Starter port when you are ready to used it, High Voltage like > 16.7V may not start. Tips: The Red lights of the battery clamp will keep flashing.
Low Voltage Protection| Red Light Flashing| <12.8V(±3%)(4S)| Please check the voltage of the Jump Starter port when you are ready to use, High Voltage. Tips: The Red lights of the battery clamp will keep flashing.
Startup| | 30S±2%|
Start Current| | 600A±10%| 0.1-0.3S 1000A

0.55 800A 25 600A

Reverse Charging Protection| Red and Green Light Flashing| Support| If there is any reverse current, The clamps will turn off the output Automatically. Tips: The Red and Green lights of the battery clamp will keep flashing.
Short-Circuit Protection| Red Light Flashing| Support| When the Two Clamps are connected, The battery clamp will be in a Short Circuit Protection Mode. Tips: The red lights of the battery clamp will keep flashing, the buzzer will sound, no output and sparks.
Reverse Polarity Protection| Red Light Flashing| Support| When the Clamps are reverse-connected to the car battery, The battery clamp will be in a Reverse Polarity Protection Mode.

Tips: The Red lights of the battery clamp will keep flashing, the buzzer will sound, no output and sparks.

High Temperature Protection| Red Light Flashing| Support| Clamps will be cut off automatically when the operation temperature is too high. Tips: Protection temperature: 80ºC ±5ºC
Working Status| Green Light On| Support| The Jump Starter is ready to start the car
Standby| | Support| The Red and Green lights of the battery clamp will be flashing when ready to use.

OPERATION INSTRUCTIONS

Charging Your Jump Starter
You can charge your Jump Starter one of two ways:

1. Using the supplied mains plug pack.
2. Insert one end of the cigarette lighter charger into the 12V auxiliary power outlet in your vehicle and insert the other end of the cigarette lighter charger into the device.

NOTE: Charging takes up to 5 hours using either charging option.

Starting your vehicle

Please ensure that your Jump Starter is no less than 50% charged. If it is below 50%, you may not be able to jumpstart your vehicle.

1. Connect the jumper lead to your Jump Starter.
2. Connect the +(red clip)to the + on your car battery.
3. Connect the -(black clip)to the – on your car battery.
4. Turn your key to start your vehicle.
5. Once your vehicle is started, disconnect the alligator clip as soon as possible.

NOTE: After starting your vehicle, remove the Jump starter as soon as possible.
WARNING: Do not connect the 2 alligator clip.
WARNING: Do not disassemble the Jump Starter

Turning on your Jump Starter
Press the power button. Your jump starter is now ready to use.

Charging devices via USB

1. You can either use the provided USB Break lead or your USB cable suitable for your digital device.
2. Connect either cable to the Jump Starter.
3. If using the provided USB breakout lead, Select the correct connection for your device.

How to use the LED torch

1. Double press the power button, and the LED light will turn on.
2. Pressing the button again will activate the strobe function.
3. Pressing the button again will activate the SOS function.
4. Pressing the button again will turn off the light.

Charging indicator

1. Press the power button to see the charge status of the Jump Starter LCD screen.
2. When charging, the LCD screen will show the specific number range from 0 to 100%.
3. The input function will stop once the jump starter is fully charged.

Wireless charging
Your Jump Starter is charging ready. You can charge a smart device wirelessly from your Jump Starter. Please make sure your device can be supported to be charged wirelessly before using this feature. If your device doesn’t support it, it will not be able to charge wirelessly from the jump starter.

1. Press the power button.
2. Place your device in the wireless charging area on the jump starter.
3. Your device will now charge wirelessly.

Running a 12V device
Your Jump Starter is capable of running a 12V device.

TROUBLESHOOTING

The power capacity of the device is shown in 100%, but it was not fullycharged in the charging process.| The battery shown 100% on the LCD Screen of the Jump Starter means stop charging, and this situation means it is semi-state of

charge, which is conducive to long-term storage when the device is not in use for a long time.

| Pull out the charge plug, then reinsert.
Nothing happens when pressing the switch button.| Low voltage protection of the device is started and the device can not be turned on.| Insert the charger plug into the 9V2A input port to activate.

FREQUENTLY ASKED QUESTIONS

How do I turn off the Jump Starter?
Press the button for 5s, the jump starter will turn off.

How long does a full charge take?
A full charge will take between 3-5 hours using either the mains or DC charging options.

How many times can I jump-start my vehicle?
This depends on the different displacements and vehicle engines. The Jump Starter can start a vehicle up to 30 times.

If not being used, how long can the Jump Starter be stored?
It is recommended to charge the Jump Starter every 3-6 months. Once the unit drops below 50% we recommend you charge it to ensure you can jump-start your vehicle.

The Jump Starter won’t start my car, Why not?

• Please ensure the unit is charged above 50%.
• Ensure the clamps are secure and not connected incorrectly.
• Ensure the battery terminals are clear and free from corrosion. if corroded, clean them and reconnect the Jump Starter as per the instructions in this manual.

WARRANTY INFORMATION

Our product is guaranteed to be free from manufacturing defects for 12 Months. If your product becomes defective during this period, Electus Distribution will repair, replace, or refund where a product is faulty; or not fit for the intended purpose. This warranty will not cover modified products; misuse or abuse of the product contrary to user instructions or packaging label; change of mind and normal wear and tear. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure. To claim warranty, please contact the place of purchase. You will need to show a receipt or other proof of purchase. Additional information may be required to process your claim. Any expenses relating to the return of your product to the store will normally have to be paid by you. The benefits to the customer given by this warranty are in addition to other rights and remedies of the Australian Consumer Law to the goods or services to which this warranty relates.

This warranty is provided by: Electus Distribution Address 46 Eastern Creek Drive, Eastern Creek NSW 2766 Ph. 1300 738 555

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>