yezz HYDROW01 Hydrogel Machine User Manual

User Manual
(Model: HYDROW01)

PRODUCT OVERVIEW

1.  Left Case
2. Display screen
3. Power interface
4. Cutting Carriage
5. Left side lock board
6. Cutting blade holder
7. Material detecting sensor
8. Pinch Rollers
9. Right side lock board
10.  Power Switch
11. Right Case

COMPONENTS

Machine

| Blade (3pcs)
---|---
| Blade holder(1 pcs)
| Pen (1 pcs)
| Power Cable (1 pcs)
| Power connector (1 pcs)

SET UP

1.  Power Place the machine on a table, then connect the power cable and press the power switch to turn ON the machine.
2. Knife installation Release the screw on the cutting carriage and remove the knife holder. Insert the blade through the bottom of the knife holder and place it back on the cutting carriage. Turn the screw to the right again to fix it in the correct position. Over time, the blade will lose its edge. You can add more cutting force to continue using the same blade, or you can replace it with a new one to ensure accurate cuts.
3. WIFI Connection Click on the Wi-Fi icon on the machine screen, select the network to connect to and enter the password. Upon successful connection, the screen will show you the IP address of the network you connected to.

HOW TO CUT YOUR FIRST SCREEN PROTECTOR? (WIFI)

1. Connecting to your WIFI network
   Please make sure you are connected to a WIFI network

2.  Login in the app
   Open the app and enter the username and password assigned.

3. Feeding the material

4. Place a hydrogel film in the machine, aligned to the left side. The machine will automatically take the paper and will be ready to cut.

5. Choosing the product
   Select the product for the protector in the machine’s screen, choosing a brand, model, and the size of the protector to print (it will depend on whether it is front protector, back protector, etc.) and then press “Cur

HOW TO CUT YOUR FIRST SCREEN PROTECTOR? (BLUETOOTH)

1. Download the APP
   Download the phone cut app on your smartphone.

2. Login in the app
   Open the app and enter the username and password assigned.

3. Bluetooth connection
   Enter”Settings” and select Bluetooth (BLE) to connect the machine with the application. .

4. Feeding the material
   Place a hydrogel film in the machine, aligned to the left side. The machine will automatically take the paper and will be ready to cut.

5. Choosing the product
   Select the product for the protector, choose the brand, model, and the size of the protector to print (it will depend on whether it is front protector, back protector, etc.), and then press”Cut”.

MACHINE SETTING

|
---|---

SPEED AND FORCE SETTINGS

Knife holder /| Gear 2-4| Gear 4-5| Gear 6-7| Gear? -8| Gear 9-10
---|---|---|---|---|---
Force| 150-200| 200-300| 300-350| 300-400| 420-500
| 100| 80| 60| 50| 40
Material| 2 layer
back skin /| 2 layer
back skin /| 4 layer soft
film /
lamina| 4 layer soft
film /
lamina| 4 layer soft
film /
lamina
Thickness
| protector treserode 2capas (0.1mm)| protector treserode 2capas (0.18mm| | |

TECHNICAL SPECIFICATION

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>