Magene P0203320 Display DY30 eBike TFT User Manual
- June 27, 2024
- Magene
Table of Contents
Magene P0203320 Display DY30 eBike TFT
Specifications
- Category: eBike TFT Display
- Model: P0203320
- Appearance: TFT
- Rated Voltage: 36V/48V
- Working Temp: -20°C to 50°C
- Storage Temp: -25°C to 55°C
- Waterproof Level: IPX7
- Display Type: TFT
- Resolution Ratio: 240*320
- Assist Level (Riding Mode): 4 levels including an AUTO mode
- Walk Assistance: Available
- Light On/Off Function: Available
- Button/Function Tone: Available
- Light Sensor: Available
- Electronic Shifting Interaction: Available
- Radar Interaction: Available
- Landscape Screen / Vertical Screen: Available
- APP Communication: Available
- Upgrading Display Content: Assist Level, Time, Error Code, Light Icon, BLE Icon, Battery Capacity, Riding Mode, Speed, Rider/Motor Power Ratio, Shifting Gear, Range, Trip, Riding Time, Avg Speed, Max Speed, Calory, Avg Power, Energy Consumption, Screen Brightness, Battery Discharge Method
Product Introduction
- Category：eBike TFT Display
- Model： P0203320
- Appearance：
Dimension
Display
Display Size: 79.854.416mm
Display Support
- Display Support Size: 73.3550.664.4mm
- Adapted Handlebar Diameter: 31.8mm (22.2mm with rubber cover)
Pin Connection Definition
Display Introduction
Status including Assist Level, Time, Error Icon, Light Icon, BLE Icon,
Battery:
-
Status
Including Assist Level， Time， Error Icon， Light Icon， BLE Icon， Battery- Assist Level (Riding Mode)： AUTO， ECO， TOUR， and TURBO total 4 normal assist levels (Riding mode)， and another 1 level stands for the walk assistance function
- Time： It shows the current time
- Error Icon ： It shows the current error
- Light Icon： The icon appears and disappears along with light/Backlight on/off operation
- BLE Icon： It always appears on the screen when the display is powered on, it means BLE is working
- Battery Capacity： It shows the percentage of battery
-
Home Page ： Riding mode， Speed， Rider/Motor Power Ratio， Shifting Gear， Range， Trip
- Riding Mode： AUTO， ECO， TOUR， TURBO 4 modes，1 mode stands for walking assistance
- Speed： Current Speed, It switches along with riding data switching operation, SPEED is the default data showing on the display when the display is powered on
- Rider/Motor Power Ratio： The power ratio between the rider and motor
- Shifting Gear： It shows the current shifting gear
- Range： It shows the distance cyclist can still ride
- Trip： Trip distance, the trip distance starts when the display is powered on and ends when the display is powered off
- Data Page： Riding Time， Avg Speed， Max Speed， calory， Rider Motor Power Ratio， Avg
-
Power， Power Consumption
- Riding Time： The trip time starts when the display is powered on and ends when the display is powered off
- Avg Speed： Average Speed in one trip
- Max Speed： Max Speed in one trip
- Calory： Calory consumption in one trip
- Rider Motor Power Ratio： Power ratio between rider and motor in one trip
- Avg Power： Average power in one trip
- Power Consumption： Average power consumption in one trip
-
Setting Page： Screen Brightness， Battery Discharge Method
- Screen Brightness： It can select manually / automatically to switch screen brightness, as well as the percentage of screen brightness under manual switching
- Battery Discharge Method： It can select two batteries to discharge together / Battery 1 Discharge / Battery 2 Discharge
Controlling Button Introduction
Including 3 Buttons: +-M
Operation: Short pressing one button, long pressing one button,
combination buttons long pressing
Including：1 button，“ ”
Operation： One button short pressing， one button long pressing， one
button double-click
Function Introduction
- Display DY30 working with single display DY12
- Power On/Off
* **Power On** ：Long pressing DY30“ ****”2s or DY12“M/ ****”2s when the display is power off
* **Power Off** ：Long pressing DY30“ ****”2s or DY12“M/ ****”2s when the display is power on
2. **Riding Modes Switching Operation**
* When there is an electronic shifting module: Short pressing DY12“M/ ****”to loop switch riding mode
* When there isn’t an electronic shifting module: Short pressing DY12“+/-” to switch riding mode | Riding Mode | DY12 LED Color / DY30 Mode Color | Remark |
|---|---|---|
| OFF | White/White | No Assist |
| AUTO | Yellow/Yellow | Auto Assist |
| ECO | Green/Green | Lowest Assist Mode |
| TOUR | Blue/Blue | Mid Assist Mode |
| TURBO | Red/Red | Highest Assist Mode |
| WALK | None/Purple | Walk Assist |
3. **Data Page Switching** Short pressing DY30“ ”to loop switch riding data
- Light On/Off Operation
Long pressing DY12“+”2s to power on light, long pressing DY12“+”2s again to power off light
Walk Assistance Operation
Pressing DY12“-”2s and hold it to start walk assistance mode， then release“-”
to stop walk assistance mode
Shifting Gear Switching
When there is electronic shifting module: Short pressing DY12“+/-”to switch
shifting gear, short pressing “+”to switch to small freewheel; Short
pressing“-”to switch to big freewheel
Function Of Setting Page
Double-clicking DY30“ ****”， it entries setting page， including screen
brightness setting， battery discharge method， short pressing DY12 “-” to loop
switch from up and down， short pressing DY12 “ + ” to entry subpage， short
pressing DY12 “ M/ ” / DY30 “ ” to return previous page， pressing DY12“M/ ”/
DY30“ ”to exit setting page
Error Code Definition
When there is a fault in the eBike system，4 LEDs of DY12 power on and flash
Error Code|
Fault
|
Solution
---|---|---
102
|
Under Voltage
|
Checking the battery and charge it
103
|
Phase current over current
| If this fault always appear, just check eBike controller or motor, it may be broken
105
|
Lack phase of motor
| 1 Checking the cable and connector between eBike controller and motor， the cable maybe broken or connector become less crowded
eBike motor or controller is broken，it needs change eBike motor
or controller
106
|
Short circuit of motor
| 1 Checking the cable and connector between eBike controller and motor， the cable maybe broken or connector become less crowded
eBike motor or controller is
broken，it needs change eBike motor or controller
107
|
Lock rotor of motor
| Over load or exceeding the uphill ability when the cyclist riding，it can recover when removing load or riding within the requirements of
uphill ability
108
|
Hall anomaly
| 1 Checking the cable and connector between eBike controller and motor， the cable maybe broken or connector become less crowded，
Hall sensor is broken，it needs
change motor
109
|
Controller over heat
| Over load or exceeding the uphill ability when the cyclist riding，it can recover when removing load or riding within the requirements of uphill ability
110
|
Throttle anomaly
| 1 Checking the cable and connector between eBike controller and throttle，the cable maybe broken or connector become less crowded， Throttle is broken，it needs change
throttle
111
|
Communication fault（Digit torque sensor）
| 1 Checking the cable and connector between eBike controller and torque sensor，the cable maybe broken or connector become less crowded
eBike controller or torque sensor is broken，it needs change eBike
controller or torque sensor
---|---|---
115
|
Temp sensor fault of controller
| Sensor is broken，it needs change controller
001
|
Communication fault（Display）
| 1 Checking the cable and connector between eBike controller and display，the cable maybe broken or connector become less crowded
eBike controller or display is broken，it needs change eBike
controller or display
002
|
Storage fault（Display）
| Display is broken，it needs change display
Mounting Instruction
- Firm display support on the handlebar, tightening the screws
- Rotating the display on the support and finishing mounting
- Display DY30 can be switched to landscape screen， unscrewing 4 screws on the buckle of the back of the display and rotating the buckle 90 °， then tightening the screws， rotating the display on the support and finishing display screen switching（Note： Landscape setting should be done on the APP）
FCC Statements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Warning:
The device has been evaluated to meet general RF exposure requirements, The
device can be used in portable exposure conditions without restriction.
Federal Communication Commission (FCC) Radiation Exposure Statement Power is
so low that no RF exposure calculation is needed.
Frequently Asked Questions (FAQ)
Q: How do I adjust the screen brightness?
A: You can manually or automatically switch the screen brightness. For manual
adjustment, you can select the desired percentage of screen brightness.
Q: What is the Battery Discharge Method setting for?
A: The Battery Discharge Method setting allows you to choose between
discharging both batteries together or selecting individual battery discharge
(Battery 1 or Battery 2).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>