Logicbus T203PM100-MU Single-Phase Ac / Dc True Rms Power Meter User Manual

USER MANUAL
T203PM100-MU
T203PM300-MU
T203PM600-MU
SINGLE-PHASE AC / DC TRUE RMS POWER METER

T203PM100-MU Single-Phase Ac / Dc True Rms Power Meter

WITH MODBUS RTU PROTOCOL AND ANALOGUE AND DIGITAL OUTPUTS

RIGINAL INSTRUCTIONS

The content of this documentation refers to products and technologies described in it.
All technical data contained in the document may be changed without notice.
The content of this documentation is subject to periodic review.
To use the product safely and effectively, read the following instructions carefully before use.
The product must be used only for the use for which it was designed and manufactured: any other use is under the full responsibility of the user.
Installation, programming and set-up are allowed only to authorized, physically and intellectually suitable operators.
Set-up must be performed only after correct installation and the user must follow all the operations described in the installation manual carefully.
Seneca is not responsible for failures, breakages and accidents caused by ignorance or failure to apply the stated requirements.
Seneca is not responsible for any unauthorized modifications.
Seneca reserves the right to modify the device, for any commercial or construction requirement, without the obligation to promptly update the reference manuals.
No liability for the contents of this document can be accepted.
Use the concepts, examples and other content at your own risk.
There may be errors and inaccuracies in this document that could damage your system, so proceed with caution, the author(s) will not take responsibility for it.
Technical specifications are subject to change without notice.

CONTACT US|
---|---
Technical support| supporto@seneca.it  
Product information| commerciale@seneca.it 

This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised

Document revisions

INTRODUCTION

ATTENTION!
This user manual extends the information from the installation manual to the configuration of the device. Use the installation manual for more information.
ATTENTION!
In any case, SENECA s.r.l. or its suppliers will not be responsible for the loss of data/revenue or consequential or incidental damages due to negligence or bad/improper management of the device, even if SENECA is well aware of these possible damages. SENECA, its subsidiaries, affiliates, group companies, suppliers and distributors do not guarantee that the functions fully meet the customer’s expectations or that the device, firmware and software should have no errors or operate continuously.
1.1. DESCRIPTION
T203PM is a transducer for measuring AC/DC current and voltage in an isolated way (insulation relating to the communication ports and the analogue and digital output), aimed at measuring energy (bidirectionally) that can be installed on DIN 46277 rail.

Measuring the voltage and current of the network, the instrument allows to measure the RMS values, instantaneous powers and energies of the devices to be monitored.
The 1.3kHz input measurement band guarantees the measurement of voltage and currents with harmonic components up to the twenty-first (at the mains frequency of 60 Hz). The use of this device is compatible with single-phase inverters.
The list of measurements made available by the tool is provided below:

• TRUE RMS AC VOLTAGE and CURRENT MEASUREMENTS (TRUE EFFECTIVE VALUE)
• DC VOLTAGE and BIPOLAR DC CURRENT MEASUREMENTS (the current can take on the +/- signs)
• MEASUREMENTS OF INSTANT POWER and ACTIVE, REACTIVE AND APPARENT ENERGY
• POWER FACTOR
• THD (AT NETWORK FREQUENCIES of 50 or 60 Hz)
• NETWORK FREQUENCY

The measured energies are stored in non-volatile memory cyclically once per second. For further information refer to the paragraph on ENERGY METERS

1.2. COMMUNICATION PORT SPECIFICATIONS

RS485 COMMUNICATION PORTS

Number| 1
Baudrate| From 2400 to 115200 bit/s configurable
Parity, Data bit, Stop bit| Configurable
Protocol| ModBUS RTU Slave
USB COMMUNICATION PORT

Number| 1
Protocol| ModBUS RTU Slave
Use| For configuration with Easy-setup software and firmware update

MEASURES AVAILABLE FROM SERIAL

2.1. CONVENTIONS
The device provides the measurement values of the powers on all 4 quadrants. The conventions for the signs of the measurements used in the product are summarized in the following image:

Where:
quadrant Q1 relates to an inductive load with imported (absorbed) active energy, classic use case.
quadrant Q2 relates to a capacitive load with exported (generated) active energy.
quadrant Q3 relates to an inductive load with exported (generated) active energy.
quadrant Q4 relates to a capacitive load with imported (absorbed) active energy.

2.2.  INSTANTANEOUS VALUES PROVIDED and MINIMUM -MAXIMUM ABSOLUTE VALUES
The following table provides the list of instant measurements provided by the instrument; all instantaneous measurements have a minimum and maximum memory that can be reset via the ModBUS CLEAR MIN/MAX command (refer to the COMMAND register in the register list)

2.3. ENERGY METERS and INITIAL SETTINGS

The following table lists the 64-bit integer counters whose values are saved in Fe-RAM (memory writable an unlimited number of times):

ACTIVE ENERGY [Wh/10] (TOTAL (+/-))

REACTIVE ENERGY [VARh/10] (TOTAL (+/-))
APPARENT ENERGY [VAh/10] (TOTAL (+/-))

To these 64-bit counters corresponds the value of the energies in 32-bit floating point value as shown in the following table (refer to the table of ModBUS registers at the end of the manual):

The ability to customize the 64-bit energy values is also made available to the user by following the following procedure which uses the sending of ModBUS commands to first unlock the write protection and then to finalize the writing in non-volatile memory:

• In the COMMAND register, send the ENABLE WRITE CUSTOM ENERGIES command
• Now the instrument no longer integrates the energies into memory; it is therefore possible to write the desired initial values in the 64bit integer registers relating to the ACTIVE / REACTIVE / APPARENT energies
• At this point it is possible to complete the writing using the ModBUS WRITE CUSTOM ENERGIES AND REBOOT command.

If, on the other hand, one only wishes to bring the values of these counters to zero, execute the ModBUS CLEAR ENERGIES command
Note:

• During normal operation, energies are saved in non-volatile memory once per second
• When customizing the energies, once the non-volatile write protection has been disabled, the device can return to normal operation using the ModBUS WRITE CUSTOM ENERGIES AND REBOOT or REBOOT commands.

EASUREMENT AND CALCULATION TIMES

3.1. SAMPLING TIMES
The sampling time of the current and voltage channels is 47000 samples per second.
The number of equivalent bits of the detected measurements is 13.5 bits
3.2. RESPONSE TIMES FOR RMS VALUES
We define the settling time as the time required for the RMS value to reach 99.5% of the full scale in response to an input from 0% to 100% of the full scale.

| DC measurements| AC measurements
---|---|---
Settling time| 500 ms max| 1000 ms max
Rise time| <250ms| <250ms
Fall time| <250ms| <250ms

3.3. RESPONSE TIMES OF THE ANALOGUE AND MODBUS OUTPUTS
Analogue Output Response Time: Typical 100ms (10-90%)
Modbus Response Time: Typical 5 ms
MEASUREMENT PRECISION AT 23°C

DEVICE CONFIGURATION

ATTENTION!
TO CONFIGURE THE DEVICE USE THE EASY SETUP 2 SOFTWARE

Measurements provided by the device are subject to the user settings. The meaning of the device configuration registers that act on the electrical measurements performed is listed below (refer to the ModBUS registers at the end of the manual):

4.1. ANALOGUE AND DIGITAL OUTPUT

The analogue and digital outputs can be associated respectively to one of the instantaneous measurements provided between VOLTAGE / CURRENT / ACTIVE P. / REACTIVE P. / APPARENT P./ FREQUENCY / PF / THD. Below you can see the configuration details separately for the analogue and digital output.
4.1.1. Analogue output
The analogue output is able to provide a voltage in the 0 ÷ 10V range; the analogue repetition of a measurement is performed by defining:

• A range of the input measurement (beginning and end of the measurement scale)
• A range of the output voltage to which the measurement will be associated (Start and end of the output scale)
  The image below graphically illustrates the values described above

MODBUS REGISTERS RELATING TO THE ANALOGUE OUTPUT

MODBUS REGISTER| DESCRIPTION
_USR_ALARMTYPEAO DO| Select the type of measurement that can be combined [V, A, W, VAR, VA, Hz, PF, THD]
_USRRO_AOOUTPUTVOLTAGE| Value of the analogue voltage generated at the output
USR_AO_STARTINSCALE| Initial value of the measurement to be repeated [V, A, W, VAR, VA, Hz, PF, THD]
USR_AO_STOPINSCALE| Final value of the measurement to be repeated [V, A, W, VAR, VA, Hz, PF, THD]
_USR_AOSTARTVOLTOUT| Minimum value of the output voltage associated with the start of the measurement scale
_USR_AOSTOPVOLTOUT| Maximum value of the output voltage associated with the end of the measurement scale

4.1.2. Digital output
The digital output is used for signalling alarms that may occur for a given measurement associated with it combined or for generating pulses related to the measured energy(*).
Below is a table with a brief description of the fields necessary to configure the digital output:

MODBUS REGISTERS RELATING TO THE DIGITAL OUTPUT

MODBUS REGISTER| DESCRIPTION
_USR_ALARMTYPEAO DO| Select the type of measurement that can be combined [V, A, W, VAR, VA, Hz, PF, THD]
_USR_ALARM_DOBEHAVIOUR| Behaviour of the alarm: NONE / MAX / MIN / INSIDE WINDOW/ OUTSIDE WINDOW / PULSES GENERATION: 1000 – 100 – 10 – 1 PULSES/kWh, 100 – 10 -1 PULSES/MWh (*)
USR_DO_ALNORMALLYHIGH| Set output as normally high or low
USR_DO_LOWVAL| Minimum alarm threshold of the measurement [V, A, W, VAR, VA, Hz, PF, THD]
USR_DO_HIGHVAL| Maximum alarm threshold of measurement [V, A, W, VAR, VA, Hz, PF, THD]
USR_DO_HIST| Hysteresis value of the min/max thresholds [V, A, W, VAR, VA, Hz, PF, THD]
USR_DO_TIMER10MS| Time spent in the alarm situation. The alarm is confirmed when this time is exceeded (multiples of 10ms)
USRRO_DO_ALSTATUS| Current alarm signalling: NO ALARM , MIN – MAX threshold PREALARM – INSIDE WINDOW – OUTSIDE WINDOW , MIN – MAX ALARM – INSIDE WINDOW – OUTSIDE WINDOW. (For numerical values refer to the list of ModBUS registers)

(*): The pulse duration is 50ms ± 10ms, the pulse generation is relative to the active energy.

USB CONNECTION and CONFIGURATION RESET

The front USB port allows a simple connection to configure the device via the configuration software.
If it is necessary to restore the instrument’s initial configuration, use the configuration software.

FIRMWARE UPDATE

It is possible to update the firmware through the USB port (for more information refer to the Easy Setup 2 software)

MODBUS COMMUNICATION PROTOCOL

The supported communication protocol is:

• Modbus RTU Slave (from both the RS485 and USB ports)
  For more information on these protocols, see the website: http://www.modbus.org/specs.php.

7.1. SUPPORTED MODBUS FUNCTION CODES
The following ModBUS functions are supported:

• Read Holding Register (function 3)
• Write Single Register (function 6)
• Write Multiple registers (function 16)

ATTENTION!
All 32-bit values are contained in 2 consecutive registers
ATTENTION!
All 64-bit values are contained in 4 consecutive registers
ATTENTION!
Any registers with RW* (in flash memory) can be written up to about 10000 times The PLC/Master ModBUS programmer must not exceed this limit

MODBUS REGISTER TABLE

The following abbreviations are used in the register tables:

MAXIMUM
RW**| Read-Write: REGISTERS THAT CAN BE WRITTEN ONLY AFTER WRITING THE
“ENABLE WRITE CUSTOM ENERGIES = 49616” COMMAND
UNSIGNED 16 BIT| Integer register without sign that can take values from 0 to 65535
SIGNED 16 BIT| Integer register with sign that can take values from -32768 to +32767
UNSIGNED 32 BIT| Integer register without sign that can take values from 0 to 4294967296
SIGNED 32 BIT| Integer register with sign that can take values from -2147483648 to 2147483647
UNSIGNED 64 BIT| Integer register without sign that can take values from 0 to 18,446,744,073,709,551,615
SIGNED 64 BIT| Integer register with sign that can assume values from -2^63 to 2^63-1
FLOAT 32 BIT| 32-bit, single-precision floating-point register (IEEE54)
https://en.wikipedia.org/wiki/IEEE_754
BIT| Boolean register, which can take the values 0 (false) or 1 (true)

8.1. NUMBERING OF “0-BASED” OR “1-BASED” MODBUS ADDRESSES

According to the ModBUS standard the Holding Registers are addressable from 0 to 65535, there are 2 different conventions for numbering the addresses: “0-BASED” and “1-BASED”. For greater clarity, Seneca shows its register tables in both conventions.

ATTENTION!
CAREFULLY READ THE DOCUMENTATION OF THE MODBUS MASTER DEVICE IN ORDER TO UNDERSTAND WHICH OF THE TWO CONVENTIONS THE MANUFACTURER HAS DECIDED TO USE
8.2. NUMBERING OF MODBUS ADDRESSES WITH “0-BASED” CONVENTION
The numbering is:

Therefore the first register is at address 0.
In the following tables, this convention is indicated with “ADDRESS OFFSET”.
8.3. NUMBERING OF MODBUS ADDRESSES WITH “1 BASED” CONVENTION (STANDARD)
The numbering is that established by the Modbus consortium and is of the type:

In the following tables this convention is indicated with “ADDRESS 4x” since a 4 is added to the address so that the first Modbus register is 40001.
A further convention is also possible where the number 4 is omitted in front of the register address:

8.4. BIT CONVENTION WITHIN A MODBUS HOLDING REGISTER
A Modbus Holding Register consists of 16 bits with the following convention:

BIT 15| BIT 14| BIT 13| BIT 12| BIT 11| BIT 10| BIT 9| BIT 8| BIT 7| BIT 6| BIT 5| BIT 4| BIT 3| BIT 2| BIT 1| BIT 0
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---

For instance, if the value of the register in decimal is 12300
the value 12300 in hexadecimal is: 0x300C the hexadecimal 0x300C in binary value is: 11 0000 0000 1100
So, using the above convention, we get:

BIT

15

| BIT

14

| BIT

13

| BIT

12

| BIT

11

| BIT

10

| BIT

9

| BIT

8

| BIT

7

| BIT

6

| BIT

5

| BIT

4

| BIT

3

| BIT

2

| BIT

1

| BIT

0

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
0| 0| 1| 1| 0| 0| 0| 0| 0| 0| 0| 0| 1| 1| 0| 0

8.5. MSB and LSB BYTE CONVENTION WITHIN A MODBUS HOLDING REGISTER

A Modbus Holding Register consists of 16 bits with the following convention:

BIT

15

| BIT

14

| BIT

13

| BIT

12

| BIT

11

| BIT

10

| BIT

9

| BIT

8

| BIT

7

| BIT

6

| BIT

5

| BIT

4

| BIT

3

| BIT

2

| BIT

1

| BIT

0

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---

LSB Byte (Least Significant Byte) defines the 8 bits ranging from Bit 0 to Bit 7 included, we define MSB Byte (Most Significant Byte) the 8 bits ranging from Bit 8 to Bit 15 inclusive:

BIT

15

| BIT

14

| BIT

13

| BIT

12

| BIT

11

| BIT

10

| BIT

9

| BIT

8

| BIT

7

| BIT

6

| BIT

5

| BIT

4

| BIT

3

| BIT

2

| BIT

1

| BIT

0

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
BYTE MSB| BYTE LSB

8.6. REPRESENTATION OF A 32-BIT VALUE IN TWO CONSECUTIVE MODBUS HOLDING REGISTERS

The representation of a 32-bit value in the ModBUS Holding Registers is made using 2 consecutive Holding Registers (a Holding Register is a 16-bit register). To obtain the 32-bit value it is therefore necessary to read two consecutive registers:
For example, if register 40064 contains the 16 most significant bits (MSW) while register 40065 contains the least significant 16 bits (LSW), the 32-bit value is obtained by composing the 2 registers:

BIT

15

| BIT

14

| BIT

13

| BIT

12

| BIT

11

| BIT

10

| BIT

9

| BIT

8

| BIT

7

| BIT

6

| BIT

5

| BIT

4

| BIT

3

| BIT

2

| BIT

1

| BIT

0

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
40064 MOST SIGNIFICANT WORD
BIT

15

| BIT

14

| BIT

13

| BIT

12

| BIT

11

| BIT

10

| BIT

9

| BIT

8

| BIT

7

| BIT

6

| BIT

5

| BIT

4

| BIT

3

| BIT

2

| BIT

1

| BIT

0

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
40065 LEAST SIGNIFICANT WORD

32 = + ( ∗ 65536)
In the reading registers it is possible to swap the most significant word with the least significant word, therefoit is possible to obtain 40064 as LSW and 40065 as MSW.

8.7.  TYPE OF 32-BIT FLOATING POINT DATA (IEEE 754)
The IEEE 754 standard (https://en.wikipedia.org/wiki/IEEE_754) defines the format for representing floating point numbers.
As already mentioned, since it is a 32-bit data type, its representation occupies two 16-bit holding registers.
To obtain a binary / hexadecimal conversion of a floating point value it is possible to refer to an online converter at this address:
http://www.h-schmidt.net/FloatConverter/IEEE754.html

Using the last representation the value 2.54 is represented at 32 bits as: 0x40228F5C
Since we have 16-bit registers available, the value must be divided into MSW and LSW: 0x4022 (16418 decimal) are the 16 most significant bits (MSW) while 0x8F5C (36700 decimal) are the 16 least significant bits (LSW).
8.8. T-203PM-MU: MODBUS 4X HOLDING REGISTERS TABLE (FUNCTION CODE 3)

ADDRESS (4x)| OFFSET| REGISTER| | DESCRIPTION| W/R| TYPE
---|---|---|---|---|---|---
40001| 0| RESERVED| | | | UNSIGNED 16 BIT
40002| 1| ROM_FWREV| | Device firmware revision| | UNSIGNED 16 BIT
40003| 2| USR_SLAVEID| | Device slave ID| RW*| UNSIGNED 16 BIT
40004| 3| RESERVED| | | RO| UNSIGNED 16 BIT
__****40005| ** **__ 4| __****** COMMAND| | Register for command execution: REBOOT=49568
WRITE TO FLASH=49600 CLEAR ENERGIES=45505 CLEAR MIN/MAX=49612 ENABLE WRITE CUSTOM ENERGIES=49616 WRITE CUSTOM ENERGIES AND REBOOT=49617| ******__ RO| __

__**__** UNSIGNED 16 BIT

40072| 71| USR_MULTV| MSW| Multiplier for voltage [> 0]| RW| __ FLOAT 32 BIT
40073| 72| LSW
40074| 73| USR_MULTI| MSW| Multiplier for current [> 0]| RW| __ FLOAT 32 BIT
40075| 74| LSW
40076| 75| __ USR_TVRATIO| MSW| __ Voltage transformation ratio [> 0]| __

RW*

| __ FLOAT 32 BIT
40077| 76| LSW
40078| 77| __ USR_AMPCUTOFF| MSW| __ current cutoff, 0 = disabled [A]| __ RW*| __ FLOAT 32 BIT
40079| 78| LSW
40080| 79| __

USR_VOLTCUTOFF

| MSW| __ voltage cutoff, 0 = disabled [V]| __ RW*| __ FLOAT 32 BIT
40081| 80| LSW
__****40082| ** 81| ******__ USR_STOPBIT_PARITY_BAUDRATE| | Bit [12] NR StopBit 0 = 1 stop bit 1 = 2 stop bit Bit [8-9] Parity 0=UART_PARITY_NONE 1=UART_PARITY_EVEN

2=UART_PARITY_ODD  __ Bit [0-7] LSB Baudrate: 0=2400 1=4800 2=9600 3=19200 4=38400 5=57600 6=115200

| __*** RW| ** UNSIGNED 16 BIT
40083*| 82| USR_MEASURE| | Selects the type of measure (0=AC or 1=DC)| RW| __

UNSIGNED 16 BIT

---|---|---|---|---|---|---
__

__

__**40084**

| __

__

__ 83

| __

__**__**

USR_ALARMTYPE_AO DO

| | Measure associated with the analog output AO

(8 Bit MSB) and digital DO (8 Bit LSB).  __

The selectable measures are: 0=NONE 1=VOLTAGE 2=CURRENT 3=ACTIVE P. 4=REACTIVE P. 5=APPARENT

P. 6=FREQUENCY 7=PF 8=THD

| __

__

__

__ RW*

| __

__

__

__

__ NSIGNED 16 BIT

__**40085| **** 84| ******__ USR_ALARM_DO_BEHAVIOUR| | Type of DO ALARMS: 0=NONE 1=MAX 2=MIN 3=INSIDE WINDOW 4=OUTSIDE WINDOW Pulses (PLS): 5=1000 PLS/kWh  6=100 PLS/kWh 7=10 PLS/kWh 8= 1 PLS/kWh 9=100 PLS/MWh 10=10 PLS/MWh 11=1 PLS/MWh| __*** RW| ** **__ UNSIGNED 16 BIT
40086| 85| __ USR_AO_STARTINSCALE| MSW| Analog output: initial value of the input [V, A, W, VAR, VA, Hz, PF, THD]| __ RW*| __ FLOAT 32 BIT
40087| 86| LSW
40088| 87| __ USR_AO_STOPINSCALE| MSW| Analog output: final value of the input [V, A, W, VAR, VA, Hz, PF, THD]| __

RW*

| __ FLOAT 32 BIT
40089| 88| LSW
40090| 89| USR_AO_STARTVOLTOUT| MSW| Analog output: minimum voltage [V]| RW| __ FLOAT 32 BIT
40091| 90| LSW
40092| 91| USR_AO_STOPVOLTOUT| MSW| Analog output: maximum voltage [V]| RW| __ FLOAT 32 BIT
40093| 92| LSW
40094| 93| USRRO_AO_OUTPUTVOLTAGE| MSW| Analog output: voltage generated at the output [V]| RO| FLOAT 32 BIT
40095| 94| LSW
40096| 95| USR_DO_ALNORMALLYHIGH| | Digital output: alarm state, 1 = normally high 0 = normally low| RW*| UNSIGNED 16 BIT
40097| 96| __

USR_DO_LOWVAL

| MSW| Digital output: lower alarm threshold [V, A, W, VAR, VA, Hz, PF, THD]| __

RW*

| __

FLOAT 32 BIT

40098| 97| LSW
40099| 98| USR_DO_HIGHVAL| MSW| Digital output: upper alarm threshold [V, A, W, VAR, VA, Hz, PF, THD]| __

RW*

| __ FLOAT 32 BIT
40100| 99| | LSW
40101| 100| __ USR_DO_HIST| MSW| Digital output: alarm hysteresis value [V, A, W, VAR, VA, Hz, PF,

THD]

| __ RW| __ FLOAT 32 BIT
40102| 101| LSW
40103| 102| USR_DO_TIMER10MS| | Digital output: time filter applied to the alarm (multiples of 10ms)| RW| UNSIGNED 16 BIT
ALL RIGHTS RESERVED. NO PART OF THISPUBLICATION MAY BE REPRODUCED WITHOUT    www.seneca.it PRIOR PERMISSION.| __ MI00571-1-EN| __ Page 21|
__

__**__**40104

| __

__**__** 103

| __ USRRO_DO_ALSTATUS| | Digital output: alarm status. 0=NONE
1=MAX_PREALARM
2=MIN_PREALARM
4=INTWIN_PRE_ALARM
8=EXTWIN_PRE_ALARM
256=MAX_ALARM
512=MIN_ALARM
1024=INTWIN_ALARM
2048=EXTWIN_ALARM| __

__

__

RO

| __

__**__**

__

UNSIGNED 16 BIT

---|---|---|---|---|---|---
40105| 104| MISRMS_F_V| MSW| RMS voltage measurement [V]| RO| __ FLOAT 32 BIT
40106| 105| LSW
40107| 106| MISRMS_F_I| MSW| RMS current measurement [A]| RO| __ FLOAT 32 BIT
40108| 107| LSW
40109| 108| MISPOW_F_ACTIVE| MSW| Active power measurement [W]| RO| __ FLOAT 32 BIT
40110| 109| LSW
40111| 110| __ MISPOW_F_REACTIVE| MSW| Reactive power measurement [VAR]| __

RO

| __ FLOAT 32 BIT
40112| 111| LSW
40113| 112| MISPOW_F_APPARENT| MSW| Apparent power measurement [VA]| RO| __ FLOAT 32 BIT
40114| 113| LSW
40115| 114| MISEN_F_ACTIVE| MSW| Active energy measurement [Wh]| RO| __ FLOAT 32 BIT
40116| 115| LSW
40117| 116| __ MISEN_F_REACTIVE| MSW| Reactive energy measurement [VARh]| __

RO

| __ FLOAT 32 BIT
40118| 117| LSW
40119| 118| MISEN_F_APPARENT| MSW| Apparent energy measurement [VAh]| RO| __ FLOAT 32 BIT
40120| 119| LSW
40121| 120| MISFREQ_F| MSW| Frequency measurement [Hz]| RO| __ FLOAT 32 BIT
40122| 121| LSW
40123| 122| __ MISPF_F| MSW| PF measurement PF (±0..1)| __

RO

| __ FLOAT 32 BIT
40124| 123| LSW
40125| 124| __ MISTHD_F| MSW| __ THD measurement (0..100%)| __

RO

| __ FLOAT 32 BIT
40126| 125| LSW
40127| 126| RESERVED| | | | UNSIGNED 32 BIT
40128| 127
40129| 128| RESERVED| | | | UNSIGNED 16 BIT
40130| 129| RESERVED| | | | FLOAT 32 BIT
40131| 130
40132| 131| RESERVED| | | | FLOAT 32 BIT
40133| 132
40134| 133| RESERVED| | | | FLOAT 32 BIT
40135| 134
40136| 135| RESERVED| | | | FLOAT 32 BIT
40137| 136| | | | |
---|---|---|---|---|---|---
40138| 137| RESERVED| | | | __ FLOAT 32 BIT
40139| 138
40140| 139| MIN_MISRMS_F_V| MSW| Minimum RMS voltage measurement [V]| RO| __

FLOAT 32 BIT

40141| 140| LSW
40142| 141| MAX_MISRMS_F_V| MSW| Maximum RMS voltage measurement [V]| RO| __

FLOAT 32 BIT

40143| 142| LSW
40144| 143| MIN_MISRMS_F_I| MSW| Minimum RMS current measurement [A]| RO| __

FLOAT 32 BIT

40145| 144| LSW
40146| 145| MAX_MISRMS_F_I| MSW| Maximum RMS current measurement [A]| RO| __

FLOAT 32 BIT

40147| 146| LSW
40148| 147| MIN_MISPOW_F_ACTIVE| MSW| Minimum active power measurement [W]| RO| FLOAT 32 BIT
40149| 148| LSW
40150| 149| MAX_MISPOW_F_ACTIVE| MSW| Maximum active power measurement [W]| RO| __

FLOAT 32 BIT

40151| 150| LSW
40152| 151| MIN_MISPOW_F_REACTIVE| MSW| Minimum reactive power measurement [VAR]| RO| __

FLOAT 32 BIT

40153| 152| LSW
40154| 153| __

MAX_MISPOW_F_REACTIVE

| MSW| Maximum reactive power measurement [VAR]| __

RO

| __

FLOAT 32 BIT

40155| 154| LSW
40156| 155| __

MIN_MISPOW_F_APPARENT

| MSW| Minimum apparent power measurement [VA]| __

RO

| __

FLOAT 32 BIT

40157| 156| LSW
40158| 157| MAX_MISPOW_F_APPARENT| MSW| Minimum apparent power measurement [VA]| RO| __

FLOAT 32 BIT

40159| 158| LSW
40160| 159| __

MIN_MISFREQ_F

| MSW| Minimum frequency measurement [Hz]| __

RO

| __

FLOAT 32 BIT

40161| 160| LSW
40162| 161| __

MAX_MISFREQ_F

| MSW| Maximum frequency measurement [Hz]| __

RO

| __

FLOAT 32 BIT

40163| 162| LSW
40164| 163| MIN_MISPF_F| MSW| Minimum PF measurement (±0..1)| RO| __

FLOAT 32 BIT

40165| 164| LSW
40166| 165| MAX_MISPF_F| MSW| Maximum PF measurement (±0..1)| RO| __

FLOAT 32 BIT

40167| 166| | LSW| | |
40168| 167| MIN_MISTHD_F| MSW| Minimum THD measurement (0..100%)| RO| __

FLOAT 32 BIT

40169| 168| | LSW
40170| 169| MAX_MISTHD_F| MSW| Maximum THD measurement (0..100%)| RO| FLOAT 32 BIT
40171| 170| | LSW
40172| 171| __

RESERVED

| MSW| | | __

UNSIGNED 32 BIT

40173| 172| LSW
40174| 173| MISRMS_INT_V| | RMS voltage measurement [V / 10]: (Example: 2300 -> 230.0 V)| RO| __ SIGNED 16 BIT
---|---|---|---|---|---|---
__**40175| 174| MISRMS_INT_I| | RMS current measurement [A/10]: (Example: 1000 -> 100.0 A)| RO| SIGNED 16 BIT
40176| 175| __**

MISPOW_INT_ACTIVE

| MSW| Active power measurement [W/10]: (Example 1000 -> 100.0

W)

| __

RO

| __

SIGNED 32 BIT

40177| 176| LSW
40178| 177| __ MISPOW_INT_REACTIVE| MSW| Reactive power measurement [VAR/10]: (Example 1000 -> 100.0 VAR)| __ RO| __ SIGNED 32 BIT
40179| 178| LSW
40180| 179| __ MISPOW_INT_APPARENT| MSW| Apparent power measurement [VA/10]: (Example 1000 -> 100.0 VA)| __ RO| __ SIGNED 32 BIT
40181| 180| LSW
40182| 181| __ EN_INT_ACTIVE| MMSW| __ Active energy measurement [Wh/10]: (Example 1000 -> 100.0

Wh)

| __**__**

RW**

| __

__ UNSIGNED 64 BIT

40183| 182| MSW
40184| 183| LSW
40185| 184| LLSW
40186| 185| __

__ EN_INT_REACTIVE

| MMSW| __

Reactive energy measurement [VARh/10]: (Example 1000 ->

100.0 VARh)

| __

__ RW**

| __ UNSIGNED 64 BIT
40187| 186| MSW
40188| 187| LSW
40189| 188| LLSW
40190| 189| __ EN_INT_APPARENT| MMSW| Apparent energy measurement [VAh/10]: (Example 1000 -> 100.0 VAh)| __

__ RW**

| __

__ UNSIGNED 64 BIT

40191| 190| MSW
40192| 191| LSW
40193| 192| LLSW
40194| 193| MIS_INT_FREQ| | Frequency measurement [Hz/10]: (Example 500 -> 50.0 Hz)| RO| UNSIGNED 16 BIT
40195| 194| MIS_INT_PF| | PF measurement [±0..1000]: (Example 755 -> 0.755)| RO| __ SIGNED 16 BIT
40196| 195| MIS_INT_THD| | THD measurement [0..100% / 10]: (Example 800 -> 80%)| RO| SIGNED 16 BIT
__**40197| 196| MIN_MISRMS_INT_V| | Minimum RMS voltage measurement [V/10]: (Example 2300 -> 230.0 V)| RO| SIGNED 16 BIT
**40198| ** 197| MAX_MISRMS_INT_V| | Maximum RMS voltage measurement [V/10]: (Example 2300 -> 230.0 V)| RO| SIGNED 16 BIT
**40199| ** 198| __ MIN_MISRMS_INT_I| | Minimum RMS current measurement [A/10]: (Example 1000 -> 100.0 A)| RO| SIGNED 16 BIT
**40200| __ 199| __ MAX_MISRMS_INT_I| | Maximum RMS current measurement [A/10]: (Example 1000 -> 100.0 A)| __

RO

| __ SIGNED 16 BIT
40201| 200| MIN_MISPOW_INT_ACTIVE| MSW| Minimum active power| RO| SIGNED 32 BIT
ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT www.seneca.itPRIOR PERMISSION.| __ MI00571-1-EN| __ Page 24|
40202| 201| | LSW| measurement [W/10]: (Example 1000 -> 100.0 W)| |
---|---|---|---|---|---|---
40203| 202| __ MAX_MISPOW_INT_ACTIVE| MSW| Maximum active power measurement [W/10]: (Example 1000 -> 100.0 W)| __ RO| __ SIGNED 32 BIT
40204| 203| LSW
40205| 204| __ MIN_MISPOW_INT_REACTIVE| MSW| Minimum reactive power measurement [VAR/10]: (Example 1000 -> 100.0 VAR)| __ RO| __ SIGNED 32 BIT
40206| 205| LSW
40207| 206| __ MAX_MISPOW_INT_REACTIVE| MSW| Maximum reactive power measurement [VAR/10]: (Example 1000 -> 100.0 VAR)| __ RO| __ SIGNED 32 BIT
40208| 207| LSW
40209| 208| __ MIN_MISPOW_INT_APPARENT| MSW| Minimum apparent power measurement [VA/10]: (Example 1000 -> 100.0 VA)| __ RO| __ SIGNED 32 BIT
40210| 209| LSW
40211| 210| __

MAX_MISPOW_INT_APPARENT

| MSW| Maximum apparent power measurement [VA/10]: (Example 1000 -> 100.0 VA)| __

RO

| __

SIGNED 32 BIT

40212| 211| LSW
__**40213| 212| MIN_MIS_INT_FREQ| | Minimum frequency measurement [Hz/10]: (Example 500 -> 50.0 Hz)| RO| SIGNED 16 BIT
**40214| ** 213| MAX_MIS_INT_FREQ| | Maximum frequency measurement [Hz/10]: (Example 500 -> 50.0 Hz)| RO| SIGNED 16 BIT
**40215| ** 214| __ MIN_MIS_INT_PF| | Minimum PF measurement [±0..1000]: (Example 755 -> 0.755)| RO| SIGNED 16 BIT
**40216| __ 215| __ MAX_MIS_INT_PF| | Maximum PF measurement [±0..1000]: (Example 755 -> 0.755)| __ RO| __ SIGNED 16 BIT
__**40217| 216| MIN_MIS_INT_THD| | Minimum THD/10 measurement (0..100%): (Example 800 -> 80.0%)| RO| SIGNED 16 BIT
**40218| ** 217| __ MAX_MIS_INT_THD| | Maximum THD/10 measurement (0..100%): (Example 800 -> 80.0%)| RO| ** SIGNED 16 BIT

By adding offset 1000 to the register it is possible to obtain the 32-bit swapped values, for example the floating point current measurement register:

40107| 106| MISRMS_F_I| MSW| Current measurement RMS [A]| RO| FLOAT 32 BIT
---|---|---|---|---|---|---
40108| 107| LSW

The same register can also be found at 41107-41108 swapped:

41107| 1106| MISRMS_F_I| LSW| Current measurement RMS [A]| RO| FLOAT 32 BIT
---|---|---|---|---|---|---
41108| 1107| MSW

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT PRIOR PERMISSION.

www.seneca.it
MI00571-1-EN

Ventas@logicbus.com
+52(33)-3823-4349

References

• IEEE-754 Floating Point Converter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>