iLight EG2-S Ethernet Gateway Installation Guide
- August 23, 2024
- ILIGHT
Table of Contents
EG2-S Ethernet Gateway
Installation Guide
Typiccal Schematic
Mounting & Installation
****EG2-S must be mounted in a suitable enclosure to provide regulatory
protection from electric shock hazard as well as protecting the iCANnet data
network from tampering that could lead to reduced network security.
Ensure selected enclosure provides adequate cooling ventilation.
Fixing to DIN rail
- Fix top clips over DIN rail.
- Pull down bottom clip using screwdriver.
- Close module towards DIN rail.
- Push up bottom clip to fix securely to DIN rail. ****
Removing from DIN rail
- Pull down bottom clip with screwdriver.
- Lift module away from DIN rail. ****
Technical Data
Electrical & Mechanical
Control: Via iLight network connection
Supply: +10 – 24V DC @ 750 mA Max (via external power supply)
Terminal Size: iCANnet cable size: 5 x 1mm?. Power cable size: 2 x Imm’
Protection: Provided by installer
Recommended Cable: iCANnet Network Cable
Ambient temperature: 2°C — 50°C
Relative humidity: 5% – 95% max, non-condensing
IP rating: IP20
Installation: Installation must be carried out by a suitably qualified
electrician
and installed in a suitable DIN rail enclosure.
Dimensions: 106mm (w) x 91mm (h) x 62mm (d)
Weight: 0.22kg
Software
For programming EG2-S, the latest version of Device Editor software is
required.
Please sign in / register at www.ilight.info for the
latest versions.
Setup
Default Password: password
When connecting to an EG2-S (with firmware version 2.03P or later) the user
must change the default password for a connection to an iLight system to be
established.
Using Link manager in Device editor create a connection and set a new
password. The new password must contain 8-64 characters, at least one lower-
case character, at least one upper-case character, at least one numeric
character and at least one special character.
Device LEDs and Buttons
Status LED
Green LED flashes — device OK
Data LED
Red LED flashes when messages sent on network.
Device Identification
Press and release switch.
Sending a message to identify the device on the
network (red Data LED flashes)
iCAN network wiring
Cable connections to the iCAN network are made to a removable 5-way connector
block located on the EG2-S
| Function | iCANnet Cable Colour |
|---|---|
| OV | Black |
| CAN L | Blue |
| Shield | Silver |
| CAN H | White |
| +V | Red |
Maximum segment distance: 500m (1640 ft) Devices per segment: 100
(without bridge or repeater) Consult iLight for information on alternative
cable types.
IMPORTANT NOTE: Connecting a mains potential cable to the iCAN Network
terminals is likley to damage the unit and other devices connected, and
invalidate warranty.
Typical Connection Diagram
Network termination
EG2-S is supplied with termination disabled as standard. If it is connected as
an end device on the iCAN network, the jumper will need to be moved to enable
termination.
To enable termination, move the jumper downwards from the top two pins to the
bottom two pins.
iLight
Usk House, Lakeside
Llantarnam Park,
Cwmbran,
NP44 3HD, UK
t: +44 (0)1923 495495
e: enquiries@iLight.co.uk
www.iLight.co.uk
****EU Authorised Representative
Cooper Lighting Netherlands B.V.
High Tech Campus
HTC 48
Eindhoven
5656 AE
E&OE. iLight reserve the right to make changes to the equipment without prior
notice.
© Signify Holding
Doc No: 9850-000916–01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>