MINISO EWL21151A RGB Wireless Charging Stand for Gaming User Manual
- June 6, 2024
- MINISO
Table of Contents
USER MANUAL
RGB WIRELESS CHARGING STAND FOR GAMING, 10W
MODEL: EWL-21151-A
PLEASE READ THIS MANUAL CAREFULLY BEFORE USING THE
PRODUCT AND KEEP IT PROPERLY.
CAUTIONS
- Do not use the product in a damp place (such as the bathroom), for contact with water may lead to product damage or malfunction.
- If water or other liquids get into the product, stop using the product.
- Do not knock, smash or drop the product. Repeated hits on it may lead to internal damage.
- The maximum temperature of the usage environment is 40 C . Keep away from high temperature and moisture. Do not expose it to direct sunlight. If you are not going to use the product for a long time, unplug it. Do not disassemble, modify or repair the product by yourself.
- Do not power it with a voltage exceeding the rated voltage.
- Do not use or touch the product with wet hand.
- Keep the product out of reach of children.
- Do not use the product on a surface of flammable objects such as carpet or quilt.
- If you fail to power the product, change the charger head and try again.
- If abnormal heat or deformation occurs during charging, stop charging immediately.
- Make sure that the Type-C cord has been inserted into the charger head fully before powering the product.
- Do not place metal items on it (such as keys, coins, batteries, or jewelry). Otherwise, it may get hot or fail to charge your device.
- Remote wireless charging cannot be achieved for now.
- Do not treat the product as unclassified municipal waste. Use separate collection facilities. Contact your local government for information about the collection system. If electrical appliances are disposed of in landfills or dumps, harmful substances can leak into groundwater, enter the food chain and harm your health.
PRODUCT OVERVIEW AND ITS ACCESSORIES
- Wireless charging stand
- Illumination strip
- Type-C charging port
Package includes
- Wireless charging stand x1
- Charging cable x1
- User Manual x1
PRODUCT PARAMETERS
| Size: 110110130mm | Input: DC 9V; DC 5V |
|---|---|
| Cord length: 0.8m | Output : 9V/1.1A; 7.5V/1A; 5V/1A |
INSTRUCTIONS
-
Before the first use, check whether the product is intact and whether the accessories are complete.
-
Connect the product to a compatible charger with the Type-C cord, place on the stand the phone or any other electronic device which has wireless magnetic charging function (in vertical or horizontal position), align it with the charging coil, then the charging can be achieved.
Note: If the phone case is too thick, it may affect the charging. It is recommended to charge your device after removing the phone case. If your device has not been aligned with the charging coil, the charging cannot be achieved, which requires you to place the device properly. -
Unplug the product after charging the phone or any other electronic device fully.
ECO-FRIENDLY WASTE DISPOSAL
You can help protect the environment! Correct Disposal of Product This mark indicates the product should not be disposed of in the same way as other household wastes in EU regions. The product should be recycled to ensure sustainable reuse of resources and to prevent potential harm for the environment and human health caused by non-control of waste management. To recycle the used appliance, apply the recycling system or contact the franchiser to recycle the product according to the environmental protection requirements.
FCC Warning:
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Caution: Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
IC Warning:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
MADE IN CHINA
www.miniso.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>