Kinderkraft JOY2 BIRDS COT USER GUIDE

: June 24, 2024
: Kinderkraft

Table of Contents

Kinderkraft JOY2 BIRDS COT USER GUIDE
Dear Client!
IMPORTANT, SAVE FOR FOR FUTURE REFERENCE
WARNING
CHANGING PAD -WARNINGS:
1. Assembling the bed:
2. Installation of equipment*:
Maintenance and cleaning Fabric bed with water
DISPOSAL OF USED EQUIPMENT
Guarantee
Specifications
FAQ (Frequently Asked Questions)
- Q: Can I use rechargeable batteries for the toy bar?
- Q: How do I adjust the crib’s base height?
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Kinderkraft JOY2 BIRDS COT USER GUIDE

Kinderkraft JOY2 BIRDS COT

USER GUIDE

MODEL: JOY² EN 12221:2008+A1:2013 EN
716-1 EN 16890:2017+A1:2021 v. 1.1

Dear Client!

Thank you for purchasing Kinderkraft products.

We create with your child in mind – we always care about safety and quality, ensuring the comfort of the best choice.

IMPORTANT, SAVE FOR FOR FUTURE REFERENCE

SAFETY INSTRUCTIONS AND PRECAUTIONS ATTENTION! SAVE FOR FUTURE REFERENCE

WARNING

Be aware of the risk of open flames and other strong heat sources such as electric or gas heaters etc. located near the product.
Do not use the product if any part is damaged, torn or missing, use only parts approved by the manufacturer.
Do not leave anything in the bed or place it next to other equipment that could support the child’s foot or pose a suffocation or hanging hazard, e.g. cables, strips of curtains or blinds.
Do not use more than one mattress in the bed.
The bed is ready for use only when the locking mechanisms are engaged. Before use, carefully check that these mechanisms are fully engaged.
The lowest position of the bottom of the bed is the safest. When the child begins to sit independently, it is recommended to use only this level.
If you leave a child in bed unattended, always check that the side entrance is zipped.
All mounting elements and fittings must be properly tightened during installation and regularly checked and tightened if necessary.
To prevent the child from being injured in a fall, the bed should no longer be used if the child is able to climbs in and out of bed.
WARNING! Use only the mattress that was delivered with the bed. Do not use another mattress, danger of suffocation.

CHANGING PAD -WARNINGS:

The changing pad is only available in the bed model with equipment.

WARNING : Do not leave a child without control

Block the bed wheels before using the changing pad.
The changing pad is intended for children up to 12 months of age with a maximum body weight of 11 kg.
You can get all additional or spare parts only from the manufacturer or distributor.
PLUSH TOY BAR – Battery safe use: Toy bar only available in bed model with equipment. It is necessary for an adult to assemble the toy bar.

Disposable batteries are not rechargeable. Do not mix different types of batteries or new and used batteries.

Batteries must be inserted with correct polarity. Used batteries should be removed from the product. Do not short-circuit the poles of the power supply. Batteries may only be charged under the supervision of an adult. Batteries should be charged outside the device.

List of bed elements: 1.
Bed frame 2.
Mattress 3.
Suspended floor* 4.
Suspended floor holders x4* 5.
Bag 6.
Changing pad 7.
Mounting slides for changing pad x2* 8.
Panel with baskets and hooks (x2) for mounting *
9. Crib rail with 3 plush toys
*Elements are only available in the equipped model.

1. Assembling the bed:

Unzip the bag and take the crib out of the bag. Unfasten the Velcro on the mattress (2). Remove the crib and other items from the set. To unfold the frame (1), place it with the wheels down (FIG. A), spread the corners enough to grasp the middle side elements, then pull the shorter sides upwards with a strong movement until they lock (FIG. B). Grasp the center elements of the longer sides and pull them firmly until they lock (FIG. C). After that, press the central part of the bottom of the bed, directing it downwards (FIG. D). The frame will unfold completely, and the bed will be blocked (FIG. E).

ATTENTION : Make sure that all four central parts of the sides of the crib are locked! The side locking mechanism will not work when the bottom of the bed is laid flat. Therefore, when locking the pages, the central part of the bottom must be raised. If the suspended floor (3) is not installed, mount it using the zipper (FIG. F) and fasten with the clip (FIG. G). Insert the support tubes (4) into the holes in the suspended floor (FIG. H and I), then the mattress (2) inside the bed (FIG. J).

ATTENTION: To ensure safety, fasten the belts under the floor starting from the side with the opening entrance (open the entrance to fasten the belts under the floor) (FIG. K and L) and ending To facilitate the installation of the opposite side, it is recommended to partially unzip the zipper around the suspended floor (FIG. M), then insert the straps into the holes and fasten them to the Velcro straps under the floor (FIG. N and O). Fasten the zipper around the floor and lock it with a buckle (FIG. P).

2. Installation of equipment*:

Pad for changing

Place the mounting slides (7) into the frame of the changing pad (6) until the locking button engages in the frame (Fig. R and S). NOTE: To facilitate slide assembly, unclip the corners on the velcro changing pad and close all snaps after the frame is assembled. Place the changing pad, pressing it firmly against the bed frame until it slides all the way to the side (FIG. T). The plastic clips on the cover with pockets should be placed on the bed frame (FIG.
IN).

Panel with baskets and mounting hooks
Insert the hooks into the holes on the panel (8), then attach them to the bed frame (FIG. W and X).

Toy rod Place the rod (9) in the swivel head in the direction of the arrow, then turn it 180° counterclockwise (FIG. Y and Z). Then install it on the base of the headband by placing it in the direction of the arrow and turning it counter-clockwise (FIG. AA). Place the mascot holders and then hang the toys on them (FIG. AB and AC).

Place the rod on one of the four sides of the frame mounting mechanism (FIG. AD).

ATTENTION: To avoid the toy bar falling on your child, make sure the toy bar is properly mounted and stable on the frame!

*3. Bed functions:**

Wheel lock: The bed has a wheel lock. To lock, press the brake lever. To unlock, lift the brake lever (FIG. AE).

Floor adjustment: there is a floor. Bed adjustable height
To lower the base, undo the zipper clip and the zipper located inside the bed together with the base inside (FIG. AF and AG). In the next step, unhook the belts from the floor and place the folding base in the bed (FIG. AH and AI).

ATTENTION: To ensure safety, fasten the straps located under the bottom (FIG. AJ). When the ground is at its lowest level, you can use the side entrance (FIG. AK).

*4. Functions of the toy bar:**

The toy bar is powered by batteries: 3 pcs. x AA (LR6) 1.5 V (not included). Battery installation/replacement:

To install or replace the battery, use a screwdriver to unscrew the battery compartment cover. Replace the batteries, paying attention to the polarity, and close the compartment with the cover again.

The bar has several buttons with the following functions:

Light switch button. The first click will turn on the light, the second click will decrease the intensity of the light. Clicking the button again will turn off the light.

The button starts the carousel. Clicking the button again will stop the carousel.

Pressing the button starts a series of soothing melodies with three volume levels. When you press the button for the fourth time, the melody will turn off.

The button activates the vibration function with three levels of intensity. After the fourth press, the function is turned off.

Maintenance and cleaning Fabric bed with water

Never clean with abrasive ammonia-based cleaners, bleach or alcohol. The bed must be well dried before use or storage.

Changing pad – clean with mild soap and water. Never clean with abrasive ammonia-based cleaners, bleach or alcohol. Allow to dry.

Toy bar – wipe with a damp cloth and mild soap. Do not submerge in water.

Toys – hand wash at a maximum temperature of 40°C, do not bleach, do not tumble dry, do not iron or dry clean.

Frame – clean the metal frame with a soft, clean, damp cloth and mild soap.

DISPOSAL OF USED EQUIPMENT

The symbol of a crossed out waste bin placed on the equipment, packaging or documents attached to it means that the product must not be disposed of with other waste.

It is the user’s responsibility to return the used equipment to a designated collection point for proper processing. Information about the available collection system for used electrical equipment can be found at the information point of the store and at the city/municipal office.

Every household is a user of electrical and electronic equipment, and therefore a potential producer of waste that is dangerous for people and the environment due to the presence of dangerous substances, mixtures and components in the equipment. On the other hand, used equipment is valuable material from which we can get raw materials such as copper, tin, glass, iron and others.

Proper handling of used equipment prevents negative consequences for the natural environment and human health!