AVTech BEEZOOM1940 4 In 1 LED Moving Head User Manual

: June 21, 2024
: AVTECH

Table of Contents

AVTech BEEZOOM1940 4 In 1 LED Moving Head
Unpacking
Product dimension
Safety Instructions
Operation Instructions
Mounting and Installation
DMX-512 control connections
DMX Channels
Display instruction
Key Features
Maintenance and Cleaning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AVTech BEEZOOM1940 4 In 1 LED Moving Head

Unpacking

Thank you for choosing our fixture. For your own safety, please read this manual before installing the device. This manual covers important information on installation and applications. Please install and operate the fixture with the following instructions. Meanwhile, please keep this manual well for future needs.
This fixture is made of a new type of high-temperature strength of engineering plastics and cast aluminium casing with a nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with the international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. It is applicable for large-scale live performances, theatre, studios, nightclubs and discos.

4-IN -1 LEDs(RGBW) which feature high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. Please check whether the following items are included inside the box:

Moving Head———One
Hanging Bracket—–Two
Safety Cable———one
Signal Cable—-One
Power Cable—-One
User Manual—-One

Product dimension

AVTech-BEEZOOM1940 -4 In 1-LED-Moving-Head-FIG-1

Safety Instructions

CAUTION!

Be careful with your operations. With a dangerous voltage, you can suffer a dangerous electric shock when touching wires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature.
This device falls under protection class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by a qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this is the case, the replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with the wall for smooth airflow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard

Operation Instructions

The fixture is for beam wash and effect use.
Don’t turn on the fixture if it’s been through severe temperature differences like after transportation because it might damage the light due to the environmental changes. So make sure to operate the fixture until it is at normal temperature.
This light should be kept away from strong shaking during any transportation or movement.
Don’t pull up the light by only the head, or it might cause damage to the mechanical parts.
Don’t expose the fixture to overheating, moisture or an environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
Make sure the installation place is in good safe condition before installing the fixture.
Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
Make sure the lenses are in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
Make sure the fixture is operated by qualified personnel who know the fixture before using it.
Keep the original packages if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.
It is not i n warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp brok e, etc.

Mounting and Installation

Cautions : For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas where the fixture might be reached by unauthorized personnel. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. Never stand directly below the device when mounting, removing, or servicing the fixture from a
periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.
Clamp Mounting : The product provides a unique mounting bracket assembly that integrates the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to the truss be sure to secure an appropriately rated clamp to the included omega bracket using an M10 screw fitted through the centre hole of the “omega bracket”. As an added safety measure be sure to attach at least one properly rated safety cable to the fixture using on of the safety cable rigging points integrated in the base assembly

AVTech-BEEZOOM1940 -4 In 1-LED-Moving-Head-FIG-4

Regardless of the rigging option you choose for our fixture, always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging po int for the safety cable and never secure a safety cable to a carrying handle.

DMX-512 control connections

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving h eads be connected together through serial linking. The cable needed should be a two-core, screened cable with XLR input and output connectors. Please refer to the diagram below. DMX-512 connection with DMX terminator

AVTech-BEEZOOM1940 -4 In 1-LED-Moving-Head-FIG-5

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the chain. Please see the illustrations below.

DMX Channels

22channels mode

CH	Function	DMX	Details
1	Pan	0-255	Pan movement control
2	Pan fine	0-255	Pan fine control
3	Tilt	0-255	Tilt movement control
4	Tilt fine	0-255	Pan fine control
5	Pan/Tilt speed	0-255	Speed from fast to slow
6	ZOOM	0-255	Zoom

__

7

| __

LENS rotation

9

| __

Strobe

| 0-3| No function, Light off
4-200| Strobe with the same step from slow to fast
201-255| Random strobe from slow to fast
10| R| 0-255| 1-100% Red linear dimmer from dark to bright
11| G| 0-255| 1-100% Green linear dimmer from dark to bright
12| B| 0-255| 1-100% Blue linear dimmer from dark to bright
13| W| 0-255| 1-100% White linear dimmer from dark to bright
14| Colour temperature| 0-255| Linear color temperature control
15| Marco| 0-255| Marco color change
__

16

| __

Static effect

| 0-9| No function
10-84| Each 5 DMX value is a kind of static effect(15 kinds)
85-255| 16th kind of effect
__

17

| __

Dynamic effect

19

| __

LED ring strobe

26 channels mode

CH	Function	DMX	Details
1	Pan	0-255	Pan movement control
2	Pan fine	0-255	Pan fine control
3	Tilt	0-255	Tilt movement control
4	Tilt fine	0-255	Pan fine control
5	Pan/Tilt speed	0-255	Speed from fast to slow
6	ZOOM	0-255	Zoom

__

7

| __

LENS rotation

9

| __

Strobe

| 0-3| No function, Light off
4-200| Strobe with the same step from slow to fast
201-255| Random strobe from slow to fast
10| R| 0-255| 1-100% Red linear dimmer from dark to bright
11| G| 0-255| 1-100% Green linear dimmer from dark to bright
12| B| 0-255| 1-100% Blue linear dimmer from dark to bright
13| W| 0-255| 1-100% White linear dimmer from dark to bright
14| Colour temperature| 0-255| Linear color temperature control
15| Marco Color| 0-255| Marco color change
__

16

| __

Static effect

| 0-9| No function
10-84| Each 5 DMX value is a kind of static effect(15 kinds)
85-255| 16th kind of effect
__

17

| __

Dynamic effect

23

| __

LED ring strobe

36 Channels mode

CH	Function	DMX	Details
1	Red	0-255	Red dimmer
2	Red Fine	0-255	Red fine control
3	Green	0-255	Green dimmer
4	Green Fine	0-255	Green fine control
5	Blue	0-255	Blue dimmer
6	Blue Fine	0-255	Blue fine control
7	White	0-255	White dimmer
8	White Fine	0-255	White fine control
9	CTO	0-255	Colour temperature linear control
10	Macro color	0-255	Marco color effect

__

11

| __

__

strobe

78Channels mode

CH	Function	DMX	Details
1	Red	0-255	Red dimmer
2	Red Fine	0-255	Red fine control
3	Green	0-255	Green dimmer
4	Green Fine	0-255	Green fine control
5	Blue	0-255	Blue dimmer
6	Blue Fine	0-255	Blue fine control
7	White	0-255	White dimmer
8	White Fine	0-255	White fine control
9	CTO	0-255	Color temperature linear control
10	Macro Color	0-255	Marco color

__

11

| __

__

strobe

21

| __

Zoom Rotation

Display instruction

AVTech-BEEZOOM1940 -4 In 1-LED-Moving-Head-
FIG-7

Key Features

Voltage: AC100V～240V 50-60HZ
Rated Power: 760W
LED Source: 19x40W high power RGBW 4 in 1 LEDs
Zoom: 7°-50°
Strobe: 0-25Hz
Control Mode: DMX512, Sound-activated, Master/slave
DMX Channels: 22/26/36/78 four channel mode
Dimmer: 0-100% linear dimmer
Pan: 540°+16 bit fine
Tilt: 220°+16 bit fine
Display: LCD colourful display
I P: IP20
Fixture dimension: 405234440mm
N.W:15.2 Kg
G.W: 18.7 Kg
Package dimension: 623951 CM (1pc/ctn)

Special Points.

Each LED can be controlled individually. With a unique honeycomb design ned lens.
The front lens can rotate without limitation in forward and reverse directions to create amazing effects.
Can be used as a beam, wash or effect light use (Kaleido effects).
With an extra LED ring for an eye-candy effect, and an LED ring with a macro effect.

Maintenance and Cleaning

The following points have to be considered during the inspection

All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded.
There must not be any deformations on the housing, colour lenses, fixations and installation spots (ceiling, suspension, trussing).
Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
The electric power supply cables must not show any damage, material fatigue or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.

CAUTION!
Disconnect from mains before starting maintenance operation.

In order to keep the lights in good condition and extend their lifetime, we suggest regular cleaning to the lights.

Clean the inside and outside lens each week to avoid the weakness of the lights due to the accumulation of dust.
Clean the fan each week.
A detailed electric check by an approved electrical engineer every three month,

make sure that the circuit contacts are in good condition, preventing the poor contact of a circuit from overheating. We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.Should you need any spare parts, please order genuine parts from your local dealer.