DynaLabs DYN-P-5000 Triaxial Piezoresistive Accelerometer Instruction Manual

Model DYN-P-5000
100g/200g/500g/2000g/6000g
Product Manual

All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors.

Product Support

If at any time you have questions or problems with the DYN-P-5000 sensors, please contact a Dynalabs engineer at:
Phone: +90 312 266 33 34 (9 a.m. to 5 p.m., UTC +3)
E-mail: info@dynalabs.com.tr

Warranty

Our products are warranted against defective materials and workmanship for one year. Defects arising from user errors are not covered by the warranty.
Copyright
All copyrights of this manual belonging to Dynalabs products are reserved. It cannot be reproduced without written consent.
Disclaimer
Dynalabs Ltd. provides this publication “as is” without warranty of any kind, express or implied, including but not limited to, the implied warranties of merchantability or fitness for a particular purpose. This document is subject to change without notice, and should not be construed as a commitment or representation by Dynalabs Ltd.
This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. will periodically update the material for inclusion in new editions. Changes and improvements to the product described in this manual may be made at any time.

Introduction

The piezoresistive accelerometers are based on micro-electro-mechanical systems (MEMS) technology. Piezoresistive accelerometers are used for high impact applications in automotive industry such as crash testing. 5000 Series Dynalabs triaxial accelerometers feature a wide range up to 5,000 Hz and excellent shock resistance up to 10,000 g. 5000 series accelerometers are lightweight. They have reliable aluminum housing with IP68 protection class. These sensors have integrated cable with configurable length and connection options.
DYN-P-5000 sensors offer the following options;

• Custom Cable Length (5m standard cable)
• Custom Housing Material
• Custom Connector
• Base plate

General Information

2.1) Unpacking and Inspection
Dynalabs products provide adequate protection for undamaged products to be transported. Document the damages that occur indirectly during the transport and contact the customer representative.
2.2) System Component s
The DYN-P-5000 has the following components:

• MEMS Sensor
• Calibration Certificate
• Product Manual

2.3) Specifications
Table 1: Specifications datasheet

Full scale accecelerati on| (g)| 5010
±100| 5020
±200| 5050
±500| 5200
±2000| 5600
±6000
---|---|---|---|---|---|---
Sensitivity| (mV/g)| 0.6| 0.6| 0.3| 0.15| 0.15
Frequency range (±5%)| (Hz)| 1,200| 1,400| 2,000| 4,500| 5,000
Non-linearity (full scale)| ( %)| 1| 1| 1| 1| 2
Shock survivability| (g)| 5,000| 5,000| 5,000| 5,000| 10,000
Transverse Sensitivity| | <3| <3| <3| <3| <3
Damping Ratio| | 0.9| 0.6| 0.6| 0.3| 0.3
Zero Acceleration
Output| (mV)| ±25| ±25| ±25| ±25| ±25

Environmental
Table 2 Environmental specifications datasheet

Physical
Table 3 Physical specifications datasheet

2.4) Outline Drawing
The dimensional properties of DYN-P-5000 sensors are given below.

Operation and Installation

3.1) General
The general sensor connector configuration is given below;
Cable Code/Pin Configuration:

WARNING
Never connect the power supply and/or the power ground to yellow, purple, blue, green, white, and/or orange cables.
Never connect the power supply to the power ground. Always use a clean power source and check the voltage range.

Sensor Static Calibration Verification

Using gravity, voltage values are measured in the + and – directions, providing a value of 1 g. The measurement should be made as follows;
When the acceleration value of 5000 series sensors is entered into the data acquisition system, the sensor shows +1 g with the effect of gravity, which is in the direction of the axis to be calibrated.
When the sensor is positioned in the opposite direction to the axis to be calibrated, the arrow shows -1g as shown below under the effect of gravity.
Using gravity, the voltage values that provide 1 g in the + and – directions are measured and compared with the catalog value. The calibration value should be close to the catalog value with a 10% tolerance. Sensor catalog sensitivity values are given in Table 1.

Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer.
The product(s) are developed, produced and tested according to following EC- directives:

• 2014/35/EU – Low Voltage Directive (LVD)
• 2006/42/EU – Machinery Safety Directive
• 2015/863/EU – RoHS Directive

Applied standards:

• EN 61010-1:2010
• EN ISO 12100:2010
• MIL-STD-810-H-2019 (Test Methods: 501.7 – High Temperature, 502.7 – Low Temperature, 514.8 – Vibration, 516.8 – Shock)

DYNALABS MÜHENDİSLİK SANAYİ TİCARET LİMİTED ŞİRKETİ declares that above mentioned products meet all the requirements of the above mentioned
standards and regulations.

Murat Aykan, Technical Manager
Ankara, 15.07.2021

Documents / Resources

| DynaLabs DYN-P-5000 Triaxial Piezoresistive Accelerometer [pdf] Instruction Manual
DYN-P-5000 Triaxial Piezoresistive Accelerometer, DYN-P-5000, DYN-P-5000 Accelerometer, Triaxial Piezoresistive Accelerometer, Piezoresistive Accelerometer, Triaxial Accelerometer, Accelerometer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>