DynaLabs DYN-C-1000-SE 1-Axis Accelerometer User Manual
- June 3, 2024
- Dynalabs
Table of Contents
DynaLabs DYN-C-1000-SE 1-Axis Accelerometer User Manual
All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors.
Product Support
If at any time you have questions or problems with the DYN-C-1000-SE sensors,
please contact a Dynalabs engineer at:
Phone: +90 312 266 33 34 (9 a.m. to 5 p.m., UTC +3)
E-mail: info@dynalabs.com.tr
Warranty
Our products are warranted against defective materials and workmanship for one
year. Defects arising from user errors are not covered by the warranty.
Copyright
All copyrights of this manual belonging to Dybala’s products are reserved. It
cannot be reproduced without written consent.
Disclaimer
Dynalabs Ltd. provides this publication “as is” without warranty of any kind,
express or implied, including but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. This document is subject
to change without notice, and should not be construed as a commitment or
representation by Dynalabs Ltd.
This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. will periodically update the material for inclusion in new editions. Changes and improvements to the product described in this manual may be made at any time.
1) Introduction
Capacitive accelerometers are based on proven micro-electro-mechanical systems (MEMS) technology. These capacitive accelerometers are reliable and long-term stable. These sensors are Single Ended type DC response sensors. The advantage of these sensors is their outstanding temperature stability, low noise- high resolution features, and their low cost. These sensors have a reliable aluminum housing with an IP68 protection class.
Dynalabs 1000SE series uniaxial accelerometers provide an outstanding noise performance from 25 to 300g/Hz. These accelerometers provide a wide frequency range (±3dB) from 1,500 Hz to 3,000 Hz.
DYN-C-1000-SE sensors offer the following options;
- Custom Cable Length
- Custom Housing Material
- Custom Connector
- Base plate
2) General Information
2.1) Unpacking and Inspection
Dynalabs products provide adequate protection for undamaged products to be transported. Document the damages that occur indirectly during the transport and contact the customer representative.
2.2) System Components
The DYN-C-1000-SE has the following components:
-MEMS Sensor
– Calibration Certificate
– Product Manual
2.3) Specifications
Table 1: Specifications datasheet
Environmental
Physical
2.4) Outline Drawing
The dimensional properties of DYN-C-1000-SE sensors are given below;
3) Operation and Installation
3.1) General
The general sensor connector configuration is given below;
Cable Code/Pin Configuration:
- Red : V + Power supply voltage +6 to +20VDC.
- Black : Ground Power GND
- White : Signal Out
- Blue : nc Not Connect
WARNING
Never connect the power supply and the power ground to white.
Never connect the power supply to the power ground.
4) Sensor Static Calibration Verification
Using gravity, voltage values are measured in the + and – directions, providing a value of 1 g. The measurement should be made as follows;
When the sensitivity value of 1000SE series sensors are entered to the data acquisition system, the sensor shows +1 g with the effect of gravity in the direction of the arrow sign.
When the sensor is in the opposite direction of the arrow, it shows -1 g with the effect of gravity.
Using gravity, the voltage values that provide 1 g in the + and directions are measured and compared with the catalog value. The calibration value should be close to the catalog value with a 10% tolerance. Sensor catalog sensitivity values are given in Table 1.
5) Declaration of Conformity
This declaration of conformity is issued under the sole responsibility of the manufacturer. The product(s) are developed, produced, and tested according to the following ECdirectives:
- 2014/35/EU Low Voltage Directive (LVD)
- 2006/42/EU Machinery Safety Directive
- 2015/863/EU RoHS Directive
Applied standards:
- EN 61010-1:2010
- EN ISO 12100:2010
- MIL-STD-810-H-2019 (Test Methods: 501.7 – High Temperature, 502.7 – Low Temperature, 514.8 – Vibration, 516.8 Shock)
DYNALABS MÜHENDSLK SANAY TCARET LMTED RKET declares that above mentioned products meet all the requirements of the above mentioned standards and regulations.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>