OHAUS i-C31M35R Shipping Scale Instruction Manual

**OHAUS i-C31M35R Shipping Scale Instruction Manual

**

REVISION HISTORY

INTRODUCTION

This manual contains installation, operation, and maintenance instructions for Courier 3000. This instruction manual helps you to install and use this scale easily. Therefore, you must read it carefully before installation and operation.

Safety Precautions

Definition of Signal Warnings and Symbols
Safety notes are marked with signal words and warning symbols. These show safety issues and warnings. Ignoring the safety notes may lead to personal injury, damage to the instrument, malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in severe injuries or death if not avoided.
CAUTION For a hazardous situation with low risk, resulting in damage to the device or the property or in loss of data, or minor or medium injuries if not avoided.
ATTENTION For important information about the product. May lead to equipment damage if not avoided.
NOTE For useful information about the product.

Warning Symbols

General hazard
Explosion hazard
Electrical shock hazard

Safety Precautions

CAUTION: Read all safety warnings before installing, making connections, or servicing this equipment. Failure to comply with these warnings could result in personal injury and/or property damage. Retain all instructions for future reference.

• Before connecting power, verify that the equipment’s input voltage range and plug type are compatible with the local AC mains power supply.
• Do not position the equipment such that it is difficult to reach the power connection.
• Make sure that the power cord does not pose a potential obstacle or tripping hazard.
• Operate the equipment only under ambient conditions specified in these instructions.
• The equipment is for indoor use only.
• Do not operate the equipment in wet, hazardous, or unstable environments.
• Do not allow liquids to enter the equipment.
• Do not load the equipment above its rated capacity.
• Do not drop loads on the platform.
• Do not place the equipment upside down on the platform.
• Use only approved accessories and peripherals.
• Disconnect the equipment from the power supply when cleaning.
• Service should only be performed by authorized personnel.

WARNING: Never work in an environment subject to explosion hazards! The housing of the instrument is not gas tight. (Explosion hazard due to spark formation, corrosion caused by the ingress of gases)

WARNING: Electrical shock hazards exist within the housing. The housing should only be opened by authorized and qualified personnel. Remove all power connections to the unit before opening.

Intended Use

This instrument is intended for use in pharmacies, schools, businesses and light industry. It must only be used for measuring the parameters described in these operating instructions. Any other type of use and operation beyond the limits of technical specifications, without written consent from OHAUS, is considered as not intended. This instrument complies with current industry standards and the recognized safety regulations; however, it can constitute a hazard in use. If the instrument is not used according to these operating instructions, the intended protection provided by the instrument may be impaired.

Overview of Parts and Controls

Figure 1-1 Courier 3000

Control Functions

Figure 1-2 Courier 3000 Control Panel

Button| |
---|---|---

Primary Function (Short Press)

| On/Zero If the scale is off, short press to turn on the scale.
When the weight on the platform is less than or equal to 2% of the Capacity value, a short press will zero the instrument display.
When the weight on the platform is greater than 2% of the Capacity value, a short press will set the tare weight.
During the calibration, short press this button to capture the zero and the linearity calibration points.
In Display Hold mode, short press this button to clear the reading shown on the instrument display.| Units/Hold Enter/exit the hold mode.
Secondary Function (Long Press)
| Off If the scale is on, long press to turn off the scale.| Cal Changes the weighing unit.
Long press two buttons to enter the calibration mode.

Figure 1-3 Display

INSTALLATION

Packing List

Unpacking the Scale

Steps

1. Take out documents, AC adapter and put them to the side.
2. Remove the foam blocks.
3. Take the Courier 3000 scale out of the box and put it on a stable surface

Setup

Power Supply Connection AC Adapter Power

1. Connect the AC Adapter to the terminal.
2. Plug the AC Adapter into the electrical outlet.

Dry Battery Power

3 disposable AA size dry batteries (not included) can supply power to the scale.

1. Remove the terminal.
2. Install the batteries in the battery compartment.

Direct Wall Mounting

The terminal may be mounted directly to a wall or table using two screws (not included). You can select the appropriate size screws that fit into the holes at the bottom of the terminal housing. See Figure A. When mounting to a wall without a solid backing, you can use the appropriate anchoring hardware.

Figure A. Direct Wall Mount Arrangement

Leveling the Equipment

Place the scale on a firm and stable flat surface and avoid excessive airflow, vibration, heat sources, or rapid

OPERATION

Turning On/Off the Scale

To turn on the scale, you can short press the On/Zero button. The scale displays the software version and enters the weighing mode.

To turn the scale off, you can long press the Off button until OFF is displayed.

Setting the Display to Zero

The value of the display can be set to zero in the following cases:

1. When the scale is turned on, it will perform an initial zero.
2. When the weight on the platform is less than or equal to 2% of the Capacity value, short press the ON/ZERO Off button to zero the instrument display.
3. When the weight on the platform is greater than 2% of the Capacity value, short press the ON/ZERO Off button to set the tare weight, then the instrument display will show a reading of 0.

If you want to set the value of the display by pressing the ON/ZERO Off button, please make sure that the scale is stable.

Changing the Units of Measure

To change the weighing unit, you can long press the Units/Hold button until the desired weighing unit appears on the display.

Calibration

Linear calibration
The scale performs linearity calibration with 3 calibration points. The zero calibration point is established with no load on the platform. The mid calibration point and the full calibration point are established with loads on the platform.

Calibration Procedures:

1. After powering on, long press the UNITS/Hold button and On/Zero button simultaneously until CAL appears on the instrument display.

2. Release the UNITS/Hold button and On/Zero button at the same time.

3. Short press the On/Zero button and -C- will appear on the instrument display. The scale will perform a zero calibration at this time (Do not place any weight on the platform).
   When the zero calibration is completed, the display will show “C XXX kg” or “C XXX lb”, depending on the current unit. For different models, the readings displayed are as follows:
   C31M35R: 10 kg (20 lb)
   C31M75R: 25 kg (50 lb)
   C31M75L: 25 kg (50 lb)
   C31M200R: 100 kg (200 lb)
   C31M200L: 100 kg (200 lb)

4. Place the load on the platform.

5. Short press the On/Zero button and -C- will appear on the instrument display. The scale will perform a midpoint calibration at this time.
   When the midpoint calibration is completed, the display will show “C XXX kg” or “C XXX lb”, depending on the current unit. For different models, the readings displayed are as follows:
   C31M35R: 30 kg (60 lb)
   C31M75R: 75 kg (150 lb)
   C31M75L: 75 kg (150 lb)
   C31M200R: 200 kg (400 lb)
   C31M200L: 200 kg (400 lb)

6. Place the load on the platform.

7. Short press the On/Zero button and -C- will appear on the instrument display. The scale will perform a top range calibration at this time.

NOTE:

• When the calibration is completed, the display will return to weighing.
• If the display shows CAL E and then exits the calibration mode, this indicates that calibration has failed.

Application Modes

Weighing
This mode is the default factory setting, and it is used to determine the weight of the loads in the selected unit of measure.

Starting to Weigh

1. Put a weight on the scale. Once the value is stable, you can see “” on the display.
   If a container is used, placed the empty container on the platform. The display will show the container’s weight in the selected weight unit. Once the platform is stable, the stable weight symbol “” will appear on the display.

2. To capture the weight of the container (the Tare weight), press the On/Zero key. Once the platform is stable the weight will be captured, the display will return to zero and the stable weight symbol “*” will appear on the display.

3. Fill the container as required. The net weight of the contents of the container will be shown on the display. Once the platform is stable, the stable weight symbol “*” will appear on the display.

Display Hold
In Display Hold mode, the instrument will hold the displayed reading for the weight on the platform if that weight is greater than 5 divisions.

1. Short press the Units/Hold button.
2. Place the load on the platform. When the weight is greater than 5d and stable, the display will show the Hold symbol “o” and the weight display will remain even after the load is removed or changes. This is useful for large boxes.
3. To clear the Hold weight on the display and exit Display Hold mode, short press the On/Zero key once. The display will then show the current weight on the platform.

NOTE: After zeroing, the display will restart to capture the first reading with a stable weight value greater than 5 d.

MAINTENANCE

Cleaning

For Courier 3000, the housing may be cleaned with a cloth dampened with a mild detergent if necessary.
CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE CLEANING.

WARNING: Electric Shock Hazard. Disconnect the equipment from the power supply before cleaning. Make sure that no liquid enters the interior of the instrument.

Attention: Do not use solvents, harsh chemicals, ammonia or abrasive cleaning agents.

The housing may be cleaned with a cloth dampened with a mild detergent if necessary

Troubleshooting

1. Power cord not plugged in or properly connected.
2. Power outlet not supplying power.
3. Batteries out of power.
4. Other failure.

|

1. Check power cord connections. Make sure power cord is plugged in properly into the power outlet.
2. Check power source.
3. Change batteries.
4. Service required.

Cannot zero the scale, or will not zero when turned on.|

1. Weights on the platform exceeds allowable limits.
2. Weight is not stable.
3. Load cell is damaged.

|

1. Remove weights from the platform.
2. Wait for platform to become stable, check area around the scale and weight on scale for excessive vibration.
3. Service required.

Error 8.1| Weight reading exceeds the maximum capacity value.|

1. Remove weight from the platform.
2. Recalibrate the scale (See 3.4).

Error 8.2| Weight reading below the minimum capacity value.|

1. Add weight to the platform.
2. Recalibrate the scale.

Error 8.3| Weight reading exceeds Overload limit.| Reduce load on the platform.
Error 8.4| Weight reading below Underload limit.|

1. Add weight to the platform.
2. Recalibrate the scale.

Battery symbol flashing| Low battery| Remove dry cell.
Lo bAt OFF| Low battery| Remove dry cell.
C L  E| Calibration failure| Use correct calibration weight.

Service Information

If the troubleshooting section does not resolve your problem, you can contact an authorized OHAUS Service
Agent. For Service assistance in the United States, call toll-free 1-800-526-0659 between 8:00 AM and 5:00 PM Eastern Standard Time. An OHAUS Product Service Specialist will be available to assist you. Outside the USA, please visit our website www.ohaus.com to locate the OHAUS office nearest you.

TECHNICAL DATA

Specifications

Table 5-1 Models Specification

Model| i-C31M35R| i-C31M75R| i-C31M200R| i-C31M75L| i-C31M200L
---|---|---|---|---|---
Capacity × Readability| 35 kg x 0.02 kg70 lb x 0.05 lb| 75 kg x 0.05 kg150 lb x 0.1 lb| 200 kg x 0.1 kg400 lb x 0.2 lb| 75 kg x 0.05 kg150 lb x 0.1 lb| 200 kg x 0.1 kg400 lb x 0.2 lb
Maximum Displayed Resolution| 1:1,750| 1:1,500| 1:2,000| 1:1,500| 1:2,000
Weighing Units| kg, lb
Application Mode| Weighing, Display Hold
Operating Temperature Range| 14°F to 104°F / -10°C to 40°C
Keyboard| 2 mechanical function keys
Display| 28 mm / 1.1 in digit height LCD display with white backlight
Stabilization Time| 1 second
Power| Dry cell battery: 3 x AA (LR6) Batteries orAC Power adapter: 100-240VAC ~ 0.5A 50/60Hz; power output: 5.0 VDC 1.0 A
Battery Life| 100 hours continuous use with backlight off
Safe Overload Capacity| 150% of capacity
Construction| ABS Plastic Indicator HousingPainted steel base with rubber feet – L models with smooth platform and adjustable feet, R models with raised, embossed tread
Cable Length| 2m
Platform Dimensions (L x W x H)| 329 x 319 x 43.5 mm / 13.0 x 12.6 x1.7 in| 520 x 400 x 52.9 mm / 20.5 x 15.7 x 2.1 in
Net Weight| 2.7 kg / 6.0 lb| 8 kg / 17.6 lb
Shipping Weight| 3.4 kg / 7.5 lb| 9 kg / 19.8 lb
Shipping Dimensions| 395 x 385 x 155 mm / 15.6 x 15.2 x 6.1 in| 600 x 485 x 100 mm / 23.6 x 19.1 x 3.9 in

Drawings and Dimensions

Terminal Dimensions (All Models)

Ohaus Corporation
8 Campus Drive
Suite 105
Parsippany, NJ 07054 USA
Tel: +1 973 377 9000
Fax: +1 973 944 7177
With offices worldwide / Con oficinas en todo el mundo / Avec des bureaux partoutdans le monde / MitBürosweltweit / Con uffici in tuttoilmondo
www.ohaus.com

P/N 30809950 A © 2022 Ohaus Corporation, all rights reserved / todos los derechos reservados / tous droits réservés / alle Rechte vorbehalten / tutti i diritti riservati 1.888.610.7664 www.calcert.com sales@calcert.com

References

• Calcert
• Lab Balance | Industrial Scales | Lab Equipment | Lab Instruments | OHAUS
• CE Declarations | OHAUS
• UK Declarations | OHAUS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>