MT2SD Quick Start Guide
v1.0 2022.07

Aircraft

The aircraft features Obstacle Sensing and Infrared Sensing System, and a fully stabilized 3-axis gimbal with a 1/2.3” CMOS sensor camera that shoots 2.7K video and 12-megapixel photos.

1. Gimbal and Camera
2. Power Button
3. Battery Level LEDs
4. Downward Vision System
5. Infrared Sensing System
6. Motors
7. Propellers
8. Antennas
9. Battery Cover
10. Charging/Upgrading Port (USB-C)
11. micro SD Card Slot
12. Aircraft Status Indicator

Remote Controller

Built into the remote controller is DJI’s long-range transmission technology OCUSYNCTM 2.0, offering a maximum transmission range of 6.21 mi (10 km)* and displaying video from the aircraft to DJI Fly on your mobile device at up to 1080p.

1. Power Button
2. Flight Mode Switch
3. Flight Pause/RTH Button
4. Battery Level LEDs
5. Control Sticks
6. Customizable Button
7. Photo/Video Toggle
8. Remote Controller Cable
9. Mobile Device Holder
10. USB-C Port
11. Control Sticks Storage Slot
12. Gimbal Dial
13. Shoot/Record Button

*The remote controller reaches its maximum transmission distance (FCC) in a wide-open area with no electromagnetic interference at an altitude of approx. 400 ft (120 m).

Download the DJI Fly App and Watching Tutorial Videos

Search “DJI Fly” in the App Store or Google Play or scan the QR code below to download the app on your mobile device.
Watch the tutorial videos on the official DJI website or in DJI Fly by tapping the icon in the top right corner of your screen.

| DJI Fly is compatible with iOS 11.0 (or later) or Android 6.0 (or later).
---|---

Charging the Batteries

Charge to activate the Intelligent Flight Battery before using for the first time.

Checking the Battery Levels and Powering On/Off

Press once to check the battery level.
Press, then press and hold to turn on/off.

Preparing the Aircraft

1. Remove the gimbal cover from the camera.

2. Unfold the front arms and the propellers.

3. Unfold the rear arms and the propellers.

4. Unfolded

| Unfold the front arms and the propellers before the rear ones. All arms and propellers must be unfolded before takeoff.
---|---

Preparing the Remote Controller

1. Attach the control sticks.

2. Pull out the mobile device holder, and then unplug the end with mobile phone mark of the RC cable.

3. Place the mobile device onto the mobile device holder, and plug the RC cable into the mobile device.

|

• Ensure the control sticks are firmly mounted.
• The remote controller cable with the Lightning connector is mounted by default. Use the appropriate cable for your mobile device to connect to the remote controller.

---|---

Preparing for Takeoff

1. Power on the remote controller

2. Power on the aircraft

3. Launch DJI Fly App

Flight

• Remote Controller Operation

Specifications

Aircraft (Model: MT2SD)

(CE/SRRC/MIC)

5.8 GHz:< 26 dBm (FCC),< 23 dBm (SRRC), <14 dBm (CE)

Remote Controller (Model: RC231)

5.8 GHz:< 26 dBm (FCC),< 23 dBm (SRRC),< 14 dBm (CE)

Operating Voltage| 1200mA @ 3.6 V (Android)

700mA @ 3.6 V (iOS)

Intelligent Flight Battery (Model: BWX161-2250-7.7)

For more information, read the User Manual on the official DJI website.

※ This content is subject to change without prior notice.

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI MINI 2 SE
Model Number: MT2SD
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

The aircraft complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.

This remote controller complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MINI 2 SE) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance EU contact address: DJI GmbH, Industries trasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MINI 2 SE) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro- compliance

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

References

• Anatel — Agência Nacional de Telecomunicações
• DJI - Official Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>