Parrot Uncle BB881-6 110V 6 Light Chandelier Instruction Manual

Parrot Uncle BB881-6 110V 6 Light Chandelier

Product Information

The Parrotuncle B88817-6 110V is a 6-light chandelier designed for installation and use in residential environments. It comes with a crystal diagram consisting of 13pcs and 6pcs crystals, adding anelegant touch to any room. The chandelier  requires a 40-watt max.
candelabra-base incandescent bulb or CFL/LED equivalent (not included) for operation.

Product Usage Instructions

WARNING: Before starting any installation or maintenance procedures, ensure that the power is shut off at the fuse or circuit breaker to prevent electrical shock.

Assembly Instructions

1. Insert a 40-watt max. candelabra-base incandescent bulb or CFL/LED equivalent (not included) into the socket (E) of the chandelier.
2. Refer to the crystal diagram provided and carefully attach the 13pcs and 6pcs crystals to their designated spots on the chandelier.

Care and Maintenance

• Always make sure the electric current is turned off before cleaning the chandelier.
• Use a soft, moist cloth with mild non-abrasive soap to clean the fixture. Avoid using glass cleaner as it may damage the metal finish.
• To clean the glass shades, wash them in a towel-lined sink with warm water and mild soap. Do not wash them in an automatic dishwasher.

Troubleshooting

1. Fixture may be wired incorrectly.
2. Worn or broken bulb.

|

1. Check the wiring of the fixture.
2. Replace the bulb with a new one.

Package contents

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• IMPORTANT: NEVER attempt any work without shutting off the electricity.
• Place the main power switch in the “OFF” position and unscrew the fuse(s), or switch “OFF” the circuit breaker switch(es), that control the power to the fixture or room you are working in.
• Place the wall switch in the “OFF” position. If the fixture to be replaced has a switch or pull chain, place it in the “OFF” position.
• Do not use bulbs with wattage greater than specified on this fixture.
• California Prop. 65: This lighting fixture contains chemicals known to the state of California to cause cancer, birth defects, and/or other reproductive harm. Wash hands after use.

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidateETL listing and/or C.S.A. certification of this  fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses.

ASSEMBLY INSTRUCTIONS

1. Hardware lamp body (G) Middle column (L).
   Note: The main line passes throught the middle column, which is tightened on the lower lamp body.

2. Screw fixture loop (J) onto coupling (F).
   Note: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.

3. Position threaded nipple (C) in mounting bracket (B) so when mounted:

   • The threaded nipple (C) wil protrude a minimum of 1/4 Inch beyond the ralsed center portion of the mounting bracket (B).
   • The threaded nipple (C) height is positioned so 1/2 the exterior threads of the screw collar loop (I) will extend past the canopy (A) when it is mounted.
   • Note: Canopy is only needed to determine the position of the threaded nippleand fixture loop. It will be Installed later.

4. Once the proper position of the threaded nipple (C) a d mounting bracket (B) has been determined, secure with hex nuts (D) as follows:

   • Screw one hex nut (D) onto the threaded nipple (C) and tighten against the raised portion of the mounting bracket (B).
   • Screw another hex nut (D) onto the threaded nipple (C) and tighten against the flat portion of the mounting bracket (B).
   • Screw the remaining hex nut (D) onto threaded nipple (C) and tighten against the screw collar loop (I).

5. Connect mounting bracket (B) to the outlet box with short machine screws (BB).
   Hardware Used

6. Thread chain (K) though screw collar ring (H) and canopy (A). Using the open chain links on chain (K), attach one end to screw collar loop (I) and the other end to upper fixture loop (J). Weave the fixture electrical and ground wres through every other chain link and pass through threaded nipple (C) into outlet box Lower the screw collar ring (H) and canopy (A) over the chain (K).

7. Wire connection guide:
   Ground wire:

   • For installation in the United States: Wrap ground wire from outlet box around ground screw reassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).

   • For installation In Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with the wire connector (AA).

   • Supply wires: Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
     Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
     NOTE:
     Fixture wires will either be:

   • Black and White.

   • Parallel Cord SPT-1 lamp wire with one round smooth wire and one ‘D’ shaped ribbed wire. Hard ware Used

8. Pass canopy (A) over the screw collar loop (1) Attach screw collar ring (H) to screw collar loop (I) to secure canopy (A).

9. Insert 40-watt max. candelabra-base incandescent bulb or CFL/LED equivalent (none included) into socket (E).

10. Crystal diagram

CARE AND MAINTENANCE

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

TROUBLESHOOTING

WARRANTY

Parrot Uncle warrants that its products will be free from defects in material and workmanship for one (1) year from the date of purchase by the Original Purchaser.
To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly defective parts or products to the authorized Parrot Uncle warehouse that the product was purchased from with PROOF OF PURCHASE, Original Purchaser’s name and return address and a description of the claimed product defect.
If any of the warranted products are found by Parrot Uncle, in its sole discretion, to be defective, such products will, at Parrot Uncle’s sole option and cost, be replaced, repaired or refunded less an amount directly attributable to Original Purchaser’s prior use of the product. Parrot Uncle will return the repaired or replaced product prepaid freight. This warranty does not cover labor or other costs or expenses to remove or install any defective, repaired or replaced product.
The parties here to expressly agree that Original Purchaser’s sole and exclusive remedy against Parrot Uncle shall be for the repair, replacement or refund of defective products as provided here in. This warranty extends only to product ownership by the Original Purchaser; is not transferable whether to heirs, subsequent owners, or otherwise; and is void if the Original Purchaser ceases to own the product.
This warranty does not apply to any products that have been subjected to misuse, mishandling, misapplication, connected to voltage at more than 5% above standard North American voltage, unusual use (including but not limited to use in an environment where the annual average ambient operating temperature is below 27 or above 95 degrees Fahrenheit), neglect (including but not limited to improper maintenance), accident, acts of god such as high winds, improper installation or care,failure to follow the Product’s written instructions for normal use and care, improper packaging of products returned to Parrot Uncle, modification (including but not limited to use of unauthorized parts or attachments), or adjustment or repair. Significant product exposure to chemicals, harsh cleaners, salt water or salt air will void any and all warranties on exterior finishes. This warranty only applies when all components, including transformers, have been provided by Parrot Uncle. Substituting another manufacturer’s product and/or components will render the warranty completely void.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE OR INFRINGEMENT. ORIGINAL PURCHASER SHALL IN NO EVENT BE ENTITLED TO, AND PARROT UNCLE SHALL NOT BE LIABLE FOR, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. INCLUDING, BUT NOT LIMITED TO LOSS OFPROFIT, PROMOTIONAL AND/OR MANUFACTURING EXPENSES, OVERHEAD, INJURY TO REPUTATION AND/OR LOSS OF CUSTOMERS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>